vmemmap: warn about page_structs with remote distance

[linux-2.6-omap-h63xx.git] / Documentation / scsi / ncr53c8xx.txt

diff --git a/Documentation/scsi/ncr53c8xx.txt b/Documentation/scsi/ncr53c8xx.txt
index 58ad8db333d9f6b5aeb2f011b0f9f0ee64bf70c0..230e30846ef2c1537619a2b8e0118a3cbc098acd 100644 (file)
--- a/Documentation/scsi/ncr53c8xx.txt
+++ b/Documentation/scsi/ncr53c8xx.txt
@@ -115,7 +115,7 @@ SCSI standard documentations are available at SYMBIOS ftp server:
 
           ftp://ftp.symbios.com/
 
-Usefull SCSI tools written by Eric Youngdale are available at tsx-11:
+Useful SCSI tools written by Eric Youngdale are available at tsx-11:
 
           ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsiinfo-X.Y.tar.gz
           ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsidev-X.Y.tar.gz
@@ -562,11 +562,6 @@ if only one has a flaw for some SCSI feature, you can disable the
 support by the driver of this feature at linux start-up and enable
 this feature after boot-up only for devices that support it safely.
 
-CONFIG_SCSI_NCR53C8XX_PROFILE_SUPPORT  (default answer: n)
-    This option must be set for profiling information to be gathered 
-    and printed out through the proc file system. This features may 
-    impact performances.
-
 CONFIG_SCSI_NCR53C8XX_IOMAPPED       (default answer: n)
     Answer "y" if you suspect your mother board to not allow memory mapped I/O.
     May slow down performance a little.  This option is required by
@@ -790,8 +785,8 @@ port address 0x1400.
         irqm:0     always open drain
         irqm:1     same as initial settings (assumed BIOS settings)
         irqm:2     always totem pole
-        irqm:0x10  driver will not use SA_SHIRQ flag when requesting irq
-        irqm:0x20  driver will not use SA_INTERRUPT flag when requesting irq
+        irqm:0x10  driver will not use IRQF_SHARED flag when requesting irq
+        irqm:0x20  driver will not use IRQF_DISABLED flag when requesting irq
 
     (Bits 0x10 and 0x20 can be combined with hardware irq mode option)
 
@@ -1241,15 +1236,15 @@ when the SCSI DATA IN phase is reentered after a phase mismatch.
 When an IRQ is shared by devices that are handled by different drivers, it 
 may happen that one driver complains about the request of the IRQ having 
 failed. Inder Linux-2.0, this may be due to one driver having requested the 
-IRQ using the SA_INTERRUPT flag but some other having requested the same IRQ 
+IRQ using the IRQF_DISABLED flag but some other having requested the same IRQ
 without this flag. Under both Linux-2.0 and linux-2.2, this may be caused by 
-one driver not having requested the IRQ with the SA_SHIRQ flag.
+one driver not having requested the IRQ with the IRQF_SHARED flag.
 
 By default, the ncr53c8xx and sym53c8xx drivers request IRQs with both the 
-SA_INTERRUPT and the SA_SHIRQ flag under Linux-2.0 and with only the SA_SHIRQ 
+IRQF_DISABLED and the IRQF_SHARED flag under Linux-2.0 and with only the IRQF_SHARED
 flag under Linux-2.2.
 
-Under Linux-2.0, you can disable use of SA_INTERRUPT flag from the boot 
+Under Linux-2.0, you can disable use of IRQF_DISABLED flag from the boot
 command line by using the following option:
 
      ncr53c8xx=irqm:0x20   (for the generic ncr53c8xx driver)
@@ -1257,7 +1252,7 @@ command line by using the following option:
 
 If this does not fix the problem, then you may want to check how all other 
 drivers are requesting the IRQ and report the problem. Note that if at least 
-a single driver does not request the IRQ with the SA_SHIRQ flag (share IRQ), 
+a single driver does not request the IRQ with the IRQF_SHARED flag (share IRQ),
 then the request of the IRQ obviously will not succeed for all the drivers.
 
 15. SCSI problem troubleshooting
@@ -1265,7 +1260,7 @@ then the request of the IRQ obviously will not succeed for all the drivers.
 15.1 Problem tracking
 
 Most SCSI problems are due to a non conformant SCSI bus or to buggy
-devices.  If infortunately you have SCSI problems, you can check the
+devices.  If unfortunately you have SCSI problems, you can check the
 following things:
 
 - SCSI bus cables