#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
-#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 3 = USART0 .. USART3
- * 4 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
#endif
};
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ics1523", 0x26),
+ },
+ {
+ I2C_BOARD_INFO("dac3550", 0x4d),
+ }
+};
+
#define EK_FLASH_BASE AT91_CHIPSELECT_0
-#define EK_FLASH_SIZE 0x200000
+#define EK_FLASH_SIZE SZ_2M
static struct physmap_flash_data ek_flash_data = {
- .width = 2,
+ .width = 2,
};
static struct resource ek_flash_resource = {
.num_resources = 1,
};
+static struct gpio_led ek_leds[] = {
+ { /* "user led 1", DS2 */
+ .name = "green",
+ .gpio = AT91_PIN_PB0,
+ .active_low = 1,
+ .default_trigger = "mmc0",
+ },
+ { /* "user led 2", DS4 */
+ .name = "yellow",
+ .gpio = AT91_PIN_PB1,
+ .active_low = 1,
+ .default_trigger = "heartbeat",
+ },
+ { /* "user led 3", DS6 */
+ .name = "red",
+ .gpio = AT91_PIN_PB2,
+ .active_low = 1,
+ }
+};
static void __init ek_board_init(void)
{
#endif
/* NOR Flash */
platform_device_register(&ek_flash);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* VGA */
// ek_add_device_video();
}