*
* NSLU2 board-setup
*
- * based ixdp425-setup.c:
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ *
+ * based on ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nslu2-power.c:
+ * Copyright (C) 2005 Tower Technologies
*
* Author: Mark Rakes <mrakes at mac.com>
* Author: Rod Whitby <rod@whitby.id.au>
+ * Author: Alessandro Zummo <a.zummo@towertech.it>
* Maintainers: http://www.nslu2-linux.org/
*
- * Fixed missing init_time in MACHINE_START kas11 10/22/04
- * Changed to conform to new style __init ixdp425 kas11 10/22/04
*/
-#include <linux/kernel.h>
+#include <linux/if_ether.h>
+#include <linux/irq.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/leds.h>
+#include <linux/reboot.h>
+#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
static struct flash_platform_data nslu2_flash_data = {
.map_name = "cfi_probe",
.scl_pin = NSLU2_SCL_PIN,
};
-#ifdef CONFIG_LEDS_IXP4XX
-static struct resource nslu2_led_resources[] = {
+static struct i2c_board_info __initdata nslu2_i2c_board_info [] = {
+ {
+ I2C_BOARD_INFO("x1205", 0x6f),
+ },
+};
+
+static struct gpio_led nslu2_led_pins[] = {
{
- .name = "ready", /* green led */
- .start = NSLU2_LED_GRN_GPIO,
- .end = NSLU2_LED_GRN_GPIO,
- .flags = IXP4XX_GPIO_HIGH,
+ .name = "nslu2:green:ready",
+ .gpio = NSLU2_LED_GRN_GPIO,
},
{
- .name = "status", /* red led */
- .start = NSLU2_LED_RED_GPIO,
- .end = NSLU2_LED_RED_GPIO,
- .flags = IXP4XX_GPIO_HIGH,
+ .name = "nslu2:red:status",
+ .gpio = NSLU2_LED_RED_GPIO,
},
{
- .name = "disk-1",
- .start = NSLU2_LED_DISK1_GPIO,
- .end = NSLU2_LED_DISK1_GPIO,
- .flags = IXP4XX_GPIO_LOW,
+ .name = "nslu2:green:disk-1",
+ .gpio = NSLU2_LED_DISK1_GPIO,
+ .active_low = true,
},
{
- .name = "disk-2",
- .start = NSLU2_LED_DISK2_GPIO,
- .end = NSLU2_LED_DISK2_GPIO,
- .flags = IXP4XX_GPIO_LOW,
+ .name = "nslu2:green:disk-2",
+ .gpio = NSLU2_LED_DISK2_GPIO,
+ .active_low = true,
},
};
+static struct gpio_led_platform_data nslu2_led_data = {
+ .num_leds = ARRAY_SIZE(nslu2_led_pins),
+ .leds = nslu2_led_pins,
+};
+
static struct platform_device nslu2_leds = {
- .name = "IXP4XX-GPIO-LED",
+ .name = "leds-gpio",
.id = -1,
- .num_resources = ARRAY_SIZE(nslu2_led_resources),
- .resource = nslu2_led_resources,
+ .dev.platform_data = &nslu2_led_data,
};
-#endif
static struct platform_device nslu2_i2c_gpio = {
.name = "i2c-gpio",
.resource = nslu2_uart_resources,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info nslu2_plat_eth[] = {
+ {
+ .phy = 1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device nslu2_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = nslu2_plat_eth,
+ }
+};
+
static struct platform_device *nslu2_devices[] __initdata = {
&nslu2_i2c_gpio,
&nslu2_flash,
&nslu2_beeper,
-#ifdef CONFIG_LEDS_IXP4XX
&nslu2_leds,
-#endif
+ &nslu2_eth[0],
};
static void nslu2_power_off(void)
gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
}
+static irqreturn_t nslu2_power_handler(int irq, void *dev_id)
+{
+ /* Signal init to do the ctrlaltdel action, this will bypass init if
+ * it hasn't started and do a kernel_restart.
+ */
+ ctrl_alt_del();
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t nslu2_reset_handler(int irq, void *dev_id)
+{
+ /* This is the paper-clip reset, it shuts the machine down directly.
+ */
+ machine_power_off();
+
+ return IRQ_HANDLED;
+}
+
static void __init nslu2_timer_init(void)
{
/* The xtal on this machine is non-standard. */
static void __init nslu2_init(void)
{
+ DECLARE_MAC_BUF(mac_buf);
+ uint8_t __iomem *f;
+ int i;
+
ixp4xx_sys_init();
nslu2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
nslu2_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
- pm_power_off = nslu2_power_off;
+ i2c_register_board_info(0, nslu2_i2c_board_info,
+ ARRAY_SIZE(nslu2_i2c_board_info));
/*
* This is only useful on a modified machine, but it is valuable
(void)platform_device_register(&nslu2_uart);
platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
+
+ pm_power_off = nslu2_power_off;
+
+ if (request_irq(gpio_to_irq(NSLU2_RB_GPIO), &nslu2_reset_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "NSLU2 reset button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+ gpio_to_irq(NSLU2_RB_GPIO));
+ }
+
+ if (request_irq(gpio_to_irq(NSLU2_PB_GPIO), &nslu2_power_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_HIGH,
+ "NSLU2 power button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Power Button IRQ %d not available\n",
+ gpio_to_irq(NSLU2_PB_GPIO));
+ }
+
+ /*
+ * Map in a portion of the flash and read the MAC address.
+ * Since it is stored in BE in the flash itself, we need to
+ * byteswap it if we're in LE mode.
+ */
+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x40000);
+ if (f) {
+ for (i = 0; i < 6; i++)
+#ifdef __ARMEB__
+ nslu2_plat_eth[0].hwaddr[i] = readb(f + 0x3FFB0 + i);
+#else
+ nslu2_plat_eth[0].hwaddr[i] = readb(f + 0x3FFB0 + (i^3));
+#endif
+ iounmap(f);
+ }
+ printk(KERN_INFO "NSLU2: Using MAC address %s for port 0\n",
+ print_mac(mac_buf, nslu2_plat_eth[0].hwaddr));
+
}
MACHINE_START(NSLU2, "Linksys NSLU2")
projects / linux-2.6-omap-h63xx.git / blobdiff