#include <asm/mach/flash.h>
#include <asm/mach/map.h>
+#include <asm/arch/gpio-switch.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
+#include <asm/arch/nand.h>
#include <asm/arch/irda.h>
#include <asm/arch/usb.h>
#include <asm/arch/keypad.h>
#include <asm/arch/mcbsp.h>
#include <asm/arch/omap-alsa.h>
-extern int omap_gpio_init(void);
-
static int h2_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
.resource = &h2_nor_resource,
};
-#if 0 /* REVISIT: Enable when nand_platform_data is applied */
-
static struct mtd_partition h2_nand_partitions[] = {
#if 0
/* REVISIT: enable these partitions if you make NAND BOOT
};
/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
-static struct nand_platform_data h2_nand_data = {
+static struct omap_nand_platform_data h2_nand_data = {
.options = NAND_SAMSUNG_LP_OPTIONS,
.parts = h2_nand_partitions,
.nr_parts = ARRAY_SIZE(h2_nand_partitions),
.num_resources = 1,
.resource = &h2_nand_resource,
};
-#endif
static struct resource h2_smc91x_resources[] = {
[0] = {
.srgr2 = GSYNC | CLKSP | FSGM | FPER(31),
.pcr0 = CLKXM | CLKRM | FSXP | FSRP | CLKXP | CLKRP,
- //.pcr0 = CLKXP | CLKRP, /* mcbsp: slave */
+ /*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */
};
static struct omap_alsa_codec_config alsa_config = {
.name = "H2 TSC2101",
.mcbsp_regs_alsa = &mcbsp_regs,
- .codec_configure_dev = NULL, // tsc2101_configure,
- .codec_set_samplerate = NULL, // tsc2101_set_samplerate,
- .codec_clock_setup = NULL, // tsc2101_clock_setup,
- .codec_clock_on = NULL, // tsc2101_clock_on,
- .codec_clock_off = NULL, // tsc2101_clock_off,
- .get_default_samplerate = NULL, // tsc2101_get_default_samplerate,
+ .codec_configure_dev = NULL, /* tsc2101_configure, */
+ .codec_set_samplerate = NULL, /* tsc2101_set_samplerate, */
+ .codec_clock_setup = NULL, /* tsc2101_clock_setup, */
+ .codec_clock_on = NULL, /* tsc2101_clock_on, */
+ .codec_clock_off = NULL, /* tsc2101_clock_off, */
+ .get_default_samplerate = NULL, /* tsc2101_get_default_samplerate, */
};
static struct platform_device h2_mcbsp1_device = {
static struct platform_device *h2_devices[] __initdata = {
&h2_nor_device,
- //&h2_nand_device,
+ &h2_nand_device,
&h2_smc91x_device,
&h2_irda_device,
&h2_kp_device,
&h2_mcbsp1_device,
};
-#ifdef CONFIG_I2C_BOARDINFO
-static struct i2c_board_info __initdata h2_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("tps65010", 0x48),
- .type = "tps65010",
- .irq = OMAP_GPIO_IRQ(58),
- },
- /* TODO when driver support is ready:
- * - isp1301 OTG transceiver
- * - optional ov9640 camera sensor at 0x30
- * - pcf9754 for aGPS control
- * - ... etc
- */
-};
-#endif
-
static void __init h2_init_smc91x(void)
{
if ((omap_request_gpio(0)) < 0) {
}
}
+static struct i2c_board_info __initdata h2_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("tps65010", 0x48),
+ .irq = OMAP_GPIO_IRQ(58),
+ }, {
+ I2C_BOARD_INFO("isp1301_omap", 0x2d),
+ .irq = OMAP_GPIO_IRQ(2),
+ },
+};
+
static void __init h2_init_irq(void)
{
omap1_init_common_hw();
.otg = 2,
#ifdef CONFIG_USB_GADGET_OMAP
- .hmc_mode = 19, // 0:host(off) 1:dev|otg 2:disabled
- // .hmc_mode = 21, // 0:host(off) 1:dev(loopback) 2:host(loopback)
+ .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
+ /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
- .hmc_mode = 20, // 1:dev|otg(off) 1:host 2:disabled
+ .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
#endif
.pins[1] = 3,
};
static struct omap_mmc_config h2_mmc_config __initdata = {
- .mmc [0] = {
- .enabled = 1,
+ .mmc[0] = {
+ .enabled = 1,
.wire4 = 1,
- .wp_pin = OMAP_MPUIO(3),
- .power_pin = -1, /* tps65010 gpio3 */
- .switch_pin = OMAP_MPUIO(1),
},
};
+extern struct omap_mmc_platform_data h2_mmc_data;
+
static struct omap_uart_config h2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
};
static struct omap_board_config_kernel h2_config[] __initdata = {
- { OMAP_TAG_USB, &h2_usb_config },
- { OMAP_TAG_MMC, &h2_mmc_config },
+ { OMAP_TAG_USB, &h2_usb_config },
+ { OMAP_TAG_MMC, &h2_mmc_config },
{ OMAP_TAG_UART, &h2_uart_config },
{ OMAP_TAG_LCD, &h2_lcd_config },
};
#define H2_NAND_RB_GPIO_PIN 62
-static int h2_nand_dev_ready(struct nand_platform_data *data)
+static int h2_nand_dev_ready(struct omap_nand_platform_data *data)
{
return omap_get_gpio_datain(H2_NAND_RB_GPIO_PIN);
}
h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
h2_nor_resource.end += SZ_32M - 1;
-#if 0 /* REVISIT: Enable when nand_platform_data is applied */
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
h2_nand_resource.end += SZ_4K - 1;
if (!(omap_request_gpio(H2_NAND_RB_GPIO_PIN)))
h2_nand_data.dev_ready = h2_nand_dev_ready;
-#endif
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* MMC: card detect and WP */
- // omap_cfg_reg(U19_ARMIO1); /* CD */
+ /* omap_cfg_reg(U19_ARMIO1); */ /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
/* Irda */
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
-
- /* irq for tps65010 chip */
- omap_cfg_reg(W4_GPIO58);
- if (gpio_request(58, "tps65010") == 0)
- gpio_direction_input(58);
-
-#ifdef CONFIG_I2C_BOARDINFO
- i2c_register_board_info(1, h2_i2c_board_info,
- ARRAY_SIZE(h2_i2c_board_info));
-#endif
+ omap_register_i2c_bus(1, 100, h2_i2c_board_info,
+ ARRAY_SIZE(h2_i2c_board_info));
+ h2_mmc_init();
}
static void __init h2_map_io(void)
omap1_map_common_io();
}
-#ifdef CONFIG_TPS65010
-static int __init h2_tps_init(void)
-{
- if (!machine_is_omap_h2())
- return 0;
-
- /* gpio3 for SD, gpio4 for VDD_DSP */
- /* FIXME send power to DSP iff it's configured */
-
- /* Enable LOW_PWR */
- tps65010_set_low_pwr(ON);
- return 0;
-}
-fs_initcall(h2_tps_init);
-#endif
-
MACHINE_START(OMAP_H2, "TI-H2")
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
.phys_io = 0xfff00000,
projects / linux-2.6-omap-h63xx.git / blobdiff