#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/bootmem.h>
-#include <linux/smp_lock.h>
#include <linux/interrupt.h>
#include <linux/mc146818rtc.h>
#include <linux/kernel_stat.h>
#include <linux/clockchips.h>
#include <linux/acpi_pmtmr.h>
#include <linux/module.h>
+#include <linux/dmi.h>
#include <asm/atomic.h>
#include <asm/smp.h>
/* Local APIC timer verification ok */
static int local_apic_timer_verify_ok;
+/* Disable local APIC timer from the kernel commandline or via dmi quirk */
+static int local_apic_timer_disabled;
+/* Local APIC timer works in C2 */
+int local_apic_timer_c2_ok;
+EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok);
/*
* Debug level, exported for io_apic.c
return lapic_get_version() >= 0x14;
}
+void apic_wait_icr_idle(void)
+{
+ while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
+ cpu_relax();
+}
+
+unsigned long safe_apic_wait_icr_idle(void)
+{
+ unsigned long send_status;
+ int timeout;
+
+ timeout = 0;
+ do {
+ send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY;
+ if (!send_status)
+ break;
+ udelay(100);
+ } while (timeout++ < 1000);
+
+ return send_status;
+}
+
/**
* enable_NMI_through_LVT0 - enable NMI through local vector table 0
*/
v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
apic_write_around(APIC_LVTT, v);
break;
+ case CLOCK_EVT_MODE_RESUME:
+ /* Nothing to do here */
+ break;
}
local_irq_restore(flags);
#define LAPIC_CAL_LOOPS (HZ/10)
-static __initdata volatile int lapic_cal_loops = -1;
+static __initdata int lapic_cal_loops = -1;
static __initdata long lapic_cal_t1, lapic_cal_t2;
static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
void (*real_handler)(struct clock_event_device *dev);
unsigned long deltaj;
long delta, deltapm;
+ int pm_referenced = 0;
+
+ if (boot_cpu_has(X86_FEATURE_LAPIC_TIMER_BROKEN))
+ local_apic_timer_disabled = 1;
+
+ /*
+ * The local apic timer can be disabled via the kernel
+ * commandline or from the test above. Register the lapic
+ * timer as a dummy clock event source on SMP systems, so the
+ * broadcast mechanism is used. On UP systems simply ignore it.
+ */
+ if (local_apic_timer_disabled) {
+ /* No broadcast on UP ! */
+ if (num_possible_cpus() > 1)
+ setup_APIC_timer();
+ return;
+ }
apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
"calibrating APIC timer ...\n");
/* Let the interrupts run */
local_irq_enable();
- while(lapic_cal_loops <= LAPIC_CAL_LOOPS);
+ while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
+ cpu_relax();
local_irq_disable();
"%lu (%ld)\n", (unsigned long) res, delta);
delta = (long) res;
}
+ pm_referenced = 1;
}
/* Calculate the scaled math multiplication factor */
calibration_result / (1000000 / HZ),
calibration_result % (1000000 / HZ));
-
- apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
-
- /*
- * Setup the apic timer manually
- */
local_apic_timer_verify_ok = 1;
- levt->event_handler = lapic_cal_handler;
- lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
- lapic_cal_loops = -1;
- /* Let the interrupts run */
- local_irq_enable();
+ /* We trust the pm timer based calibration */
+ if (!pm_referenced) {
+ apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
- while(lapic_cal_loops <= LAPIC_CAL_LOOPS);
+ /*
+ * Setup the apic timer manually
+ */
+ levt->event_handler = lapic_cal_handler;
+ lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
+ lapic_cal_loops = -1;
- local_irq_disable();
+ /* Let the interrupts run */
+ local_irq_enable();
- /* Stop the lapic timer */
- lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
+ while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
+ cpu_relax();
- local_irq_enable();
+ local_irq_disable();
- /* Jiffies delta */
- deltaj = lapic_cal_j2 - lapic_cal_j1;
- apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
+ /* Stop the lapic timer */
+ lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
- /* Check, if the PM timer is available */
- deltapm = lapic_cal_pm2 - lapic_cal_pm1;
- apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
+ local_irq_enable();
- local_apic_timer_verify_ok = 0;
+ /* Jiffies delta */
+ deltaj = lapic_cal_j2 - lapic_cal_j1;
+ apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
- if (deltapm) {
- if (deltapm > (pm_100ms - pm_thresh) &&
- deltapm < (pm_100ms + pm_thresh)) {
- apic_printk(APIC_VERBOSE, "... PM timer result ok\n");
- /* Check, if the jiffies result is consistent */
- if (deltaj < LAPIC_CAL_LOOPS-2 ||
- deltaj > LAPIC_CAL_LOOPS+2) {
- /*
- * Not sure, what we can do about this one.
- * When high resultion timers are active
- * and the lapic timer does not stop in C3
- * we are fine. Otherwise more trouble might
- * be waiting. -- tglx
- */
- printk(KERN_WARNING "Global event device %s "
- "has wrong frequency "
- "(%lu ticks instead of %d)\n",
- global_clock_event->name, deltaj,
- LAPIC_CAL_LOOPS);
- }
- local_apic_timer_verify_ok = 1;
- }
- } else {
/* Check, if the jiffies result is consistent */
- if (deltaj >= LAPIC_CAL_LOOPS-2 &&
- deltaj <= LAPIC_CAL_LOOPS+2) {
+ if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2)
apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
- local_apic_timer_verify_ok = 1;
- }
- }
+ else
+ local_apic_timer_verify_ok = 0;
+ } else
+ local_irq_enable();
if (!local_apic_timer_verify_ok) {
printk(KERN_WARNING
*/
if (nmi_watchdog != NMI_IO_APIC)
lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
+ else
+ printk(KERN_WARNING "APIC timer registered as dummy,"
+ " due to nmi_watchdog=1!\n");
}
/* Setup the lapic or request the broadcast */
}
early_param("nolapic", parse_nolapic);
+static int __init parse_disable_lapic_timer(char *arg)
+{
+ local_apic_timer_disabled = 1;
+ return 0;
+}
+early_param("nolapic_timer", parse_disable_lapic_timer);
+
+static int __init parse_lapic_timer_c2_ok(char *arg)
+{
+ local_apic_timer_c2_ok = 1;
+ return 0;
+}
+early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
+
static int __init apic_set_verbosity(char *str)
{
if (strcmp("debug", str) == 0)