#include <linux/interrupt.h>
#include <linux/rio.h>
#include <linux/rio_drv.h>
+#include <linux/of_platform.h>
+#include <linux/delay.h>
#include <asm/io.h>
#define IRQ_RIO_TX(m) (((struct rio_priv *)(m->priv))->txirq)
#define IRQ_RIO_RX(m) (((struct rio_priv *)(m->priv))->rxirq)
-#define RIO_REGS_BASE (CCSRBAR + 0xc0000)
#define RIO_ATMU_REGS_OFFSET 0x10c00
-#define RIO_MSG_REGS_OFFSET 0x11000
+#define RIO_P_MSG_REGS_OFFSET 0x11000
+#define RIO_S_MSG_REGS_OFFSET 0x13000
+#define RIO_ESCSR 0x158
+#define RIO_CCSR 0x15c
+#define RIO_ISR_AACR 0x10120
+#define RIO_ISR_AACR_AA 0x1 /* Accept All ID */
#define RIO_MAINT_WIN_SIZE 0x400000
#define RIO_DBELL_WIN_SIZE 0x1000
#define DOORBELL_DSR_TE 0x00000080
#define DOORBELL_DSR_QFI 0x00000010
#define DOORBELL_DSR_DIQI 0x00000001
-#define DOORBELL_TID_OFFSET 0x03
-#define DOORBELL_SID_OFFSET 0x05
+#define DOORBELL_TID_OFFSET 0x02
+#define DOORBELL_SID_OFFSET 0x04
#define DOORBELL_INFO_OFFSET 0x06
#define DOORBELL_MESSAGE_SIZE 0x08
-#define DBELL_SID(x) (*(u8 *)(x + DOORBELL_SID_OFFSET))
-#define DBELL_TID(x) (*(u8 *)(x + DOORBELL_TID_OFFSET))
+#define DBELL_SID(x) (*(u16 *)(x + DOORBELL_SID_OFFSET))
+#define DBELL_TID(x) (*(u16 *)(x + DOORBELL_TID_OFFSET))
#define DBELL_INF(x) (*(u16 *)(x + DOORBELL_INFO_OFFSET))
struct rio_atmu_regs {
u32 rowtar;
- u32 pad1;
+ u32 rowtear;
u32 rowbar;
u32 pad2;
u32 rowar;
u32 ifqdpar;
u32 pad6;
u32 ifqepar;
- u32 pad7[250];
+ u32 pad7[226];
+ u32 odmr;
+ u32 odsr;
+ u32 res0[4];
+ u32 oddpr;
+ u32 oddatr;
+ u32 res1[3];
+ u32 odretcr;
+ u32 res2[12];
u32 dmr;
u32 dsr;
u32 pad8;
/**
* fsl_rio_doorbell_send - Send a MPC85xx doorbell message
+ * @mport: RapidIO master port info
* @index: ID of RapidIO interface
* @destid: Destination ID of target device
* @data: 16-bit info field of RapidIO doorbell message
struct rio_priv *priv = mport->priv;
pr_debug("fsl_doorbell_send: index %d destid %4.4x data %4.4x\n",
index, destid, data);
- out_be32(&priv->dbell_atmu_regs->rowtar, destid << 22);
- out_be16(priv->dbell_win, data);
+ switch (mport->phy_type) {
+ case RIO_PHY_PARALLEL:
+ out_be32(&priv->dbell_atmu_regs->rowtar, destid << 22);
+ out_be16(priv->dbell_win, data);
+ break;
+ case RIO_PHY_SERIAL:
+ /* In the serial version silicons, such as MPC8548, MPC8641,
+ * below operations is must be.
+ */
+ out_be32(&priv->msg_regs->odmr, 0x00000000);
+ out_be32(&priv->msg_regs->odretcr, 0x00000004);
+ out_be32(&priv->msg_regs->oddpr, destid << 16);
+ out_be32(&priv->msg_regs->oddatr, data);
+ out_be32(&priv->msg_regs->odmr, 0x00000001);
+ break;
+ }
return 0;
}
/**
* fsl_local_config_read - Generate a MPC85xx local config space read
+ * @mport: RapidIO master port info
* @index: ID of RapdiIO interface
* @offset: Offset into configuration space
* @len: Length (in bytes) of the maintenance transaction
/**
* fsl_local_config_write - Generate a MPC85xx local config space write
+ * @mport: RapidIO master port info
* @index: ID of RapdiIO interface
* @offset: Offset into configuration space
* @len: Length (in bytes) of the maintenance transaction
/**
* fsl_rio_config_read - Generate a MPC85xx read maintenance transaction
+ * @mport: RapidIO master port info
* @index: ID of RapdiIO interface
* @destid: Destination ID of transaction
* @hopcount: Number of hops to target device
/**
* fsl_rio_config_write - Generate a MPC85xx write maintenance transaction
+ * @mport: RapidIO master port info
* @index: ID of RapdiIO interface
* @destid: Destination ID of transaction
* @hopcount: Number of hops to target device
memset(priv->msg_tx_ring.virt_buffer[priv->msg_tx_ring.tx_slot]
+ len, 0, RIO_MAX_MSG_SIZE - len);
- /* Set mbox field for message */
- desc->dport = mbox & 0x3;
+ switch (mport->phy_type) {
+ case RIO_PHY_PARALLEL:
+ /* Set mbox field for message */
+ desc->dport = mbox & 0x3;
+
+ /* Enable EOMI interrupt, set priority, and set destid */
+ desc->dattr = 0x28000000 | (rdev->destid << 2);
+ break;
+ case RIO_PHY_SERIAL:
+ /* Set mbox field for message, and set destid */
+ desc->dport = (rdev->destid << 16) | (mbox & 0x3);
- /* Enable EOMI interrupt, set priority, and set destid */
- desc->dattr = 0x28000000 | (rdev->destid << 2);
+ /* Enable EOMI interrupt and priority */
+ desc->dattr = 0x28000000;
+ break;
+ }
/* Set transfer size aligned to next power of 2 (in double words) */
desc->dwcnt = is_power_of_2(len) ? len : 1 << get_bitmask_order(len);
__setup("riohdid=", fsl_rio_get_cmdline);
+static inline void fsl_rio_info(struct device *dev, u32 ccsr)
+{
+ const char *str;
+ if (ccsr & 1) {
+ /* Serial phy */
+ switch (ccsr >> 30) {
+ case 0:
+ str = "1";
+ break;
+ case 1:
+ str = "4";
+ break;
+ default:
+ str = "Unknown";
+ break;;
+ }
+ dev_info(dev, "Hardware port width: %s\n", str);
+
+ switch ((ccsr >> 27) & 7) {
+ case 0:
+ str = "Single-lane 0";
+ break;
+ case 1:
+ str = "Single-lane 2";
+ break;
+ case 2:
+ str = "Four-lane";
+ break;
+ default:
+ str = "Unknown";
+ break;
+ }
+ dev_info(dev, "Training connection status: %s\n", str);
+ } else {
+ /* Parallel phy */
+ if (!(ccsr & 0x80000000))
+ dev_info(dev, "Output port operating in 8-bit mode\n");
+ if (!(ccsr & 0x08000000))
+ dev_info(dev, "Input port operating in 8-bit mode\n");
+ }
+}
+
/**
- * fsl_rio_setup - Setup MPC85xx RapidIO interface
- * @law_start: Starting physical address of RapidIO LAW
- * @law_size: Size of RapidIO LAW
+ * fsl_rio_setup - Setup Freescale PowerPC RapidIO interface
+ * @dev: of_device pointer
*
* Initializes MPC85xx RapidIO hardware interface, configures
* master port with system-specific info, and registers the
* master port with the RapidIO subsystem.
*/
-void fsl_rio_setup(int law_start, int law_size)
+int fsl_rio_setup(struct of_device *dev)
{
struct rio_ops *ops;
struct rio_mport *port;
- struct rio_priv *priv = NULL;
- int rc;
+ struct rio_priv *priv;
+ int rc = 0;
+ const u32 *dt_range, *cell;
+ struct resource regs;
+ int rlen;
+ u32 ccsr;
+ u64 law_start, law_size;
+ int paw, aw, sw;
+
+ if (!dev->node) {
+ dev_err(&dev->dev, "Device OF-Node is NULL");
+ return -EFAULT;
+ }
+
+ rc = of_address_to_resource(dev->node, 0, ®s);
+ if (rc) {
+ dev_err(&dev->dev, "Can't get %s property 'reg'\n",
+ dev->node->full_name);
+ return -EFAULT;
+ }
+ dev_info(&dev->dev, "Of-device full name %s\n", dev->node->full_name);
+ dev_info(&dev->dev, "Regs start 0x%08x size 0x%08x\n", regs.start,
+ regs.end - regs.start + 1);
+
+ dt_range = of_get_property(dev->node, "ranges", &rlen);
+ if (!dt_range) {
+ dev_err(&dev->dev, "Can't get %s property 'ranges'\n",
+ dev->node->full_name);
+ return -EFAULT;
+ }
+
+ /* Get node address wide */
+ cell = of_get_property(dev->node, "#address-cells", NULL);
+ if (cell)
+ aw = *cell;
+ else
+ aw = of_n_addr_cells(dev->node);
+ /* Get node size wide */
+ cell = of_get_property(dev->node, "#size-cells", NULL);
+ if (cell)
+ sw = *cell;
+ else
+ sw = of_n_size_cells(dev->node);
+ /* Get parent address wide wide */
+ paw = of_n_addr_cells(dev->node);
+
+ law_start = of_read_number(dt_range + aw, paw);
+ law_size = of_read_number(dt_range + aw + paw, sw);
+
+ dev_info(&dev->dev, "LAW start 0x%016llx, size 0x%016llx.\n",
+ law_start, law_size);
ops = kmalloc(sizeof(struct rio_ops), GFP_KERNEL);
ops->lcread = fsl_local_config_read;
port->iores.end = law_start + law_size;
port->iores.flags = IORESOURCE_MEM;
+ priv->bellirq = irq_of_parse_and_map(dev->node, 2);
+ priv->txirq = irq_of_parse_and_map(dev->node, 3);
+ priv->rxirq = irq_of_parse_and_map(dev->node, 4);
+ dev_info(&dev->dev, "bellirq: %d, txirq: %d, rxirq %d\n", priv->bellirq,
+ priv->txirq, priv->rxirq);
+
rio_init_dbell_res(&port->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff);
rio_init_mbox_res(&port->riores[RIO_INB_MBOX_RESOURCE], 0, 0);
rio_init_mbox_res(&port->riores[RIO_OUTB_MBOX_RESOURCE], 0, 0);
port->priv = priv;
rio_register_mport(port);
- priv->regs_win = ioremap(RIO_REGS_BASE, 0x20000);
+ priv->regs_win = ioremap(regs.start, regs.end - regs.start + 1);
+
+ /* Probe the master port phy type */
+ ccsr = in_be32(priv->regs_win + RIO_CCSR);
+ port->phy_type = (ccsr & 1) ? RIO_PHY_SERIAL : RIO_PHY_PARALLEL;
+ dev_info(&dev->dev, "RapidIO PHY type: %s\n",
+ (port->phy_type == RIO_PHY_PARALLEL) ? "parallel" :
+ ((port->phy_type == RIO_PHY_SERIAL) ? "serial" :
+ "unknown"));
+ /* Checking the port training status */
+ if (in_be32((priv->regs_win + RIO_ESCSR)) & 1) {
+ dev_err(&dev->dev, "Port is not ready. "
+ "Try to restart connection...\n");
+ switch (port->phy_type) {
+ case RIO_PHY_SERIAL:
+ /* Disable ports */
+ out_be32(priv->regs_win + RIO_CCSR, 0);
+ /* Set 1x lane */
+ setbits32(priv->regs_win + RIO_CCSR, 0x02000000);
+ /* Enable ports */
+ setbits32(priv->regs_win + RIO_CCSR, 0x00600000);
+ break;
+ case RIO_PHY_PARALLEL:
+ /* Disable ports */
+ out_be32(priv->regs_win + RIO_CCSR, 0x22000000);
+ /* Enable ports */
+ out_be32(priv->regs_win + RIO_CCSR, 0x44000000);
+ break;
+ }
+ msleep(100);
+ if (in_be32((priv->regs_win + RIO_ESCSR)) & 1) {
+ dev_err(&dev->dev, "Port restart failed.\n");
+ rc = -ENOLINK;
+ goto err;
+ }
+ dev_info(&dev->dev, "Port restart success!\n");
+ }
+ fsl_rio_info(&dev->dev, ccsr);
+
+ port->sys_size = (in_be32((priv->regs_win + RIO_PEF_CAR))
+ & RIO_PEF_CTLS) >> 4;
+ dev_info(&dev->dev, "RapidIO Common Transport System size: %d\n",
+ port->sys_size ? 65536 : 256);
+
priv->atmu_regs = (struct rio_atmu_regs *)(priv->regs_win
+ RIO_ATMU_REGS_OFFSET);
priv->maint_atmu_regs = priv->atmu_regs + 1;
priv->dbell_atmu_regs = priv->atmu_regs + 2;
- priv->msg_regs = (struct rio_msg_regs *)(priv->regs_win
- + RIO_MSG_REGS_OFFSET);
+ priv->msg_regs = (struct rio_msg_regs *)(priv->regs_win +
+ ((port->phy_type == RIO_PHY_SERIAL) ?
+ RIO_S_MSG_REGS_OFFSET : RIO_P_MSG_REGS_OFFSET));
+
+ /* Set to receive any dist ID for serial RapidIO controller. */
+ if (port->phy_type == RIO_PHY_SERIAL)
+ out_be32((priv->regs_win + RIO_ISR_AACR), RIO_ISR_AACR_AA);
/* Configure maintenance transaction window */
out_be32(&priv->maint_atmu_regs->rowbar, 0x000c0000);
out_be32(&priv->dbell_atmu_regs->rowar, 0x8004200b);
fsl_rio_doorbell_init(port);
- return;
+ return 0;
err:
if (priv)
iounmap(priv->regs_win);
+ kfree(ops);
kfree(priv);
kfree(port);
+ return rc;
+}
+
+/* The probe function for RapidIO peer-to-peer network.
+ */
+static int __devinit fsl_of_rio_rpn_probe(struct of_device *dev,
+ const struct of_device_id *match)
+{
+ int rc;
+ printk(KERN_INFO "Setting up RapidIO peer-to-peer network %s\n",
+ dev->node->full_name);
+
+ rc = fsl_rio_setup(dev);
+ if (rc)
+ goto out;
+
+ /* Enumerate all registered ports */
+ rc = rio_init_mports();
+out:
+ return rc;
+};
+
+static const struct of_device_id fsl_of_rio_rpn_ids[] = {
+ {
+ .compatible = "fsl,rapidio-delta",
+ },
+ {},
+};
+
+static struct of_platform_driver fsl_of_rio_rpn_driver = {
+ .name = "fsl-of-rio",
+ .match_table = fsl_of_rio_rpn_ids,
+ .probe = fsl_of_rio_rpn_probe,
+};
+
+static __init int fsl_of_rio_rpn_init(void)
+{
+ return of_register_platform_driver(&fsl_of_rio_rpn_driver);
}
+
+subsys_initcall(fsl_of_rio_rpn_init);
projects / linux-2.6-omap-h63xx.git / blobdiff