*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/serial_8250.h>
#include <linux/sm501.h>
+#include <linux/sm501-regs.h>
#include <linux/pm.h>
+#include <linux/fb.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
#include <asm/machvec.h>
#include <asm/rts7751r2d.h>
-#include <asm/voyagergx.h>
#include <asm/io.h>
-
-static void __init voyagergx_serial_init(void)
-{
- unsigned long val;
-
- /*
- * GPIO Control
- */
- val = readl((void __iomem *)GPIO_MUX_HIGH);
- val |= 0x00001fe0;
- writel(val, (void __iomem *)GPIO_MUX_HIGH);
-
- /*
- * Power Mode Gate
- */
- val = readl((void __iomem *)POWER_MODE0_GATE);
- val |= (POWER_MODE0_GATE_U0 | POWER_MODE0_GATE_U1);
- writel(val, (void __iomem *)POWER_MODE0_GATE);
-
- val = readl((void __iomem *)POWER_MODE1_GATE);
- val |= (POWER_MODE1_GATE_U0 | POWER_MODE1_GATE_U1);
- writel(val, (void __iomem *)POWER_MODE1_GATE);
-}
+#include <asm/spi.h>
static struct resource cf_ide_resources[] = {
[0] = {
.end = PA_AREA5_IO + 0x80c,
.flags = IORESOURCE_MEM,
},
+#ifndef CONFIG_RTS7751R2D_1 /* For R2D-1 polling is preferred */
[2] = {
.start = IRQ_CF_IDE,
.flags = IORESOURCE_IRQ,
},
+#endif
};
static struct pata_platform_info pata_info = {
},
};
+static struct spi_board_info spi_bus[] = {
+ {
+ .modalias = "rtc-r9701",
+ .max_speed_hz = 1000000,
+ .mode = SPI_MODE_3,
+ },
+};
+
+static void r2d_chip_select(struct sh_spi_info *spi, int cs, int state)
+{
+ BUG_ON(cs != 0); /* Single Epson RTC-9701JE attached on CS0 */
+ ctrl_outw(state == BITBANG_CS_ACTIVE, PA_RTCCE);
+}
+
+static struct sh_spi_info spi_info = {
+ .num_chipselect = 1,
+ .chip_select = r2d_chip_select,
+};
+
+static struct resource spi_sh_sci_resources[] = {
+ {
+ .start = 0xffe00000,
+ .end = 0xffe0001f,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device spi_sh_sci_device = {
+ .name = "spi_sh_sci",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(spi_sh_sci_resources),
+ .resource = spi_sh_sci_resources,
+ .dev = {
+ .platform_data = &spi_info,
+ },
+};
+
static struct resource heartbeat_resources[] = {
[0] = {
.start = PA_OUTPORT,
#ifdef CONFIG_MFD_SM501
static struct plat_serial8250_port uart_platform_data[] = {
{
- .membase = (void __iomem *)VOYAGER_UART_BASE,
- .mapbase = VOYAGER_UART_BASE,
+ .membase = (void __iomem *)0xb3e30000,
+ .mapbase = 0xb3e30000,
.iotype = UPIO_MEM,
- .irq = IRQ_SM501_U0,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .irq = IRQ_VOYAGER,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
.regshift = 2,
.uartclk = (9600 * 16),
},
.flags = IORESOURCE_MEM,
},
[2] = {
- .start = IRQ_SM501_CV,
+ .start = IRQ_VOYAGER,
.flags = IORESOURCE_IRQ,
},
};
+static struct fb_videomode sm501_default_mode = {
+ .pixclock = 35714,
+ .xres = 640,
+ .yres = 480,
+ .left_margin = 105,
+ .right_margin = 50,
+ .upper_margin = 35,
+ .lower_margin = 0,
+ .hsync_len = 96,
+ .vsync_len = 2,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+};
+
+static struct sm501_platdata_fbsub sm501_pdata_fbsub_pnl = {
+ .def_bpp = 16,
+ .def_mode = &sm501_default_mode,
+ .flags = SM501FB_FLAG_USE_INIT_MODE |
+ SM501FB_FLAG_USE_HWCURSOR |
+ SM501FB_FLAG_USE_HWACCEL |
+ SM501FB_FLAG_DISABLE_AT_EXIT,
+};
+
+static struct sm501_platdata_fbsub sm501_pdata_fbsub_crt = {
+ .flags = (SM501FB_FLAG_USE_INIT_MODE |
+ SM501FB_FLAG_USE_HWCURSOR |
+ SM501FB_FLAG_USE_HWACCEL |
+ SM501FB_FLAG_DISABLE_AT_EXIT),
+
+};
+
+static struct sm501_platdata_fb sm501_fb_pdata = {
+ .fb_route = SM501_FB_OWN,
+ .fb_crt = &sm501_pdata_fbsub_crt,
+ .fb_pnl = &sm501_pdata_fbsub_pnl,
+ .flags = SM501_FBPD_SWAP_FB_ENDIAN,
+};
+
+static struct sm501_initdata sm501_initdata = {
+ .gpio_high = {
+ .set = 0x00001fe0,
+ .mask = 0x0,
+ },
+ .devices = SM501_USE_USB_HOST,
+};
+
+static struct sm501_platdata sm501_platform_data = {
+ .init = &sm501_initdata,
+ .fb = &sm501_fb_pdata,
+};
+
static struct platform_device sm501_device = {
.name = "sm501",
.id = -1,
+ .dev = {
+ .platform_data = &sm501_platform_data,
+ },
.num_resources = ARRAY_SIZE(sm501_resources),
.resource = sm501_resources,
};
#endif
&cf_ide_device,
&heartbeat_device,
+ &spi_sh_sci_device,
};
static int __init rts7751r2d_devices_setup(void)
{
+ spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus));
return platform_add_devices(rts7751r2d_devices,
ARRAY_SIZE(rts7751r2d_devices));
}
addr <= cf_ide_resources[1].end));
}
-static void rts7751r2d_writeb(u8 b, void __iomem *addr)
+void rts7751r2d_writeb(u8 b, void __iomem *addr)
{
unsigned long tmp = (unsigned long __force)addr;
ctrl_outb(b, tmp);
}
-static u8 rts7751r2d_readb(void __iomem *addr)
+u8 rts7751r2d_readb(void __iomem *addr)
{
unsigned long tmp = (unsigned long __force)addr;
*/
static void __init rts7751r2d_setup(char **cmdline_p)
{
+ void __iomem *sm501_reg;
u16 ver = ctrl_inw(PA_VERREG);
printk(KERN_INFO "Renesas Technology Sales RTS7751R2D support.\n");
ctrl_outw(0x0000, PA_OUTPORT);
pm_power_off = rts7751r2d_power_off;
- voyagergx_serial_init();
+ /* sm501 dram configuration:
+ * ColSizeX = 11 - External Memory Column Size: 256 words.
+ * APX = 1 - External Memory Active to Pre-Charge Delay: 7 clocks.
+ * RstX = 1 - External Memory Reset: Normal.
+ * Rfsh = 1 - Local Memory Refresh to Command Delay: 12 clocks.
+ * BwC = 1 - Local Memory Block Write Cycle Time: 2 clocks.
+ * BwP = 1 - Local Memory Block Write to Pre-Charge Delay: 1 clock.
+ * AP = 1 - Internal Memory Active to Pre-Charge Delay: 7 clocks.
+ * Rst = 1 - Internal Memory Reset: Normal.
+ * RA = 1 - Internal Memory Remain in Active State: Do not remain.
+ */
+
+ sm501_reg = (void __iomem *)0xb3e00000 + SM501_DRAM_CONTROL;
+ writel(readl(sm501_reg) | 0x00f107c0, sm501_reg);
+
+ /*
+ * Power Mode Gate - Enable UART0
+ */
+
+ sm501_reg = (void __iomem *)0xb3e00000 + SM501_POWER_MODE_0_GATE;
+ writel(readl(sm501_reg) | (1 << SM501_GATE_UART0), sm501_reg);
+
+ sm501_reg = (void __iomem *)0xb3e00000 + SM501_POWER_MODE_1_GATE;
+ writel(readl(sm501_reg) | (1 << SM501_GATE_UART0), sm501_reg);
}
/*
.mv_irq_demux = rts7751r2d_irq_demux,
.mv_writeb = rts7751r2d_writeb,
.mv_readb = rts7751r2d_readb,
-#if defined(CONFIG_MFD_SM501) && defined(CONFIG_USB_OHCI_HCD)
- .mv_consistent_alloc = voyagergx_consistent_alloc,
- .mv_consistent_free = voyagergx_consistent_free,
-#endif
};
projects / linux-2.6-omap-h63xx.git / blobdiff