-.text
+ .section .text.page_aligned
#include <linux/linkage.h>
#include <asm/segment.h>
#include <asm/page.h>
-#
-# wakeup_code runs in real mode, and at unknown address (determined at run-time).
-# Therefore it must only use relative jumps/calls.
-#
-# Do we need to deal with A20? It is okay: ACPI specs says A20 must be enabled
-#
-# If physical address of wakeup_code is 0x12345, BIOS should call us with
-# cs = 0x1234, eip = 0x05
-#
-
-#define BEEP \
- inb $97, %al; \
- outb %al, $0x80; \
- movb $3, %al; \
- outb %al, $97; \
- outb %al, $0x80; \
- movb $-74, %al; \
- outb %al, $67; \
- outb %al, $0x80; \
- movb $-119, %al; \
- outb %al, $66; \
- outb %al, $0x80; \
- movb $15, %al; \
- outb %al, $66;
-
-ALIGN
- .align 4096
-ENTRY(wakeup_start)
-wakeup_code:
- wakeup_code_start = .
- .code16
-
- cli
- cld
-
- # setup data segment
- movw %cs, %ax
- movw %ax, %ds # Make ds:0 point to wakeup_start
- movw %ax, %ss
-
- testl $4, realmode_flags - wakeup_code
- jz 1f
- BEEP
-1:
- mov $(wakeup_stack - wakeup_code), %sp # Private stack is needed for ASUS board
-
- pushl $0 # Kill any dangerous flags
- popfl
-
- movl real_magic - wakeup_code, %eax
- cmpl $0x12345678, %eax
- jne bogus_real_magic
-
- testl $1, realmode_flags - wakeup_code
- jz 1f
- lcall $0xc000,$3
- movw %cs, %ax
- movw %ax, %ds # Bios might have played with that
- movw %ax, %ss
-1:
-
- testl $2, realmode_flags - wakeup_code
- jz 1f
- mov video_mode - wakeup_code, %ax
- call mode_set
-1:
-
- # set up page table
- movl $swsusp_pg_dir-__PAGE_OFFSET, %eax
- movl %eax, %cr3
-
- testl $1, real_efer_save_restore - wakeup_code
- jz 4f
- # restore efer setting
- movl real_save_efer_edx - wakeup_code, %edx
- movl real_save_efer_eax - wakeup_code, %eax
- mov $0xc0000080, %ecx
- wrmsr
-4:
- # make sure %cr4 is set correctly (features, etc)
- movl real_save_cr4 - wakeup_code, %eax
- movl %eax, %cr4
-
- # need a gdt -- use lgdtl to force 32-bit operands, in case
- # the GDT is located past 16 megabytes.
- lgdtl real_save_gdt - wakeup_code
-
- movl real_save_cr0 - wakeup_code, %eax
- movl %eax, %cr0
- jmp 1f
-1:
- movl real_magic - wakeup_code, %eax
- cmpl $0x12345678, %eax
- jne bogus_real_magic
-
- testl $8, realmode_flags - wakeup_code
- jz 1f
- BEEP
-1:
- ljmpl $__KERNEL_CS, $wakeup_pmode_return
-
-real_save_gdt: .word 0
- .long 0
-real_save_cr0: .long 0
-real_save_cr3: .long 0
-real_save_cr4: .long 0
-real_magic: .long 0
-video_mode: .long 0
-realmode_flags: .long 0
-real_efer_save_restore: .long 0
-real_save_efer_edx: .long 0
-real_save_efer_eax: .long 0
-
-bogus_real_magic:
- jmp bogus_real_magic
-
-/* This code uses an extended set of video mode numbers. These include:
- * Aliases for standard modes
- * NORMAL_VGA (-1)
- * EXTENDED_VGA (-2)
- * ASK_VGA (-3)
- * Video modes numbered by menu position -- NOT RECOMMENDED because of lack
- * of compatibility when extending the table. These are between 0x00 and 0xff.
- */
-#define VIDEO_FIRST_MENU 0x0000
-
-/* Standard BIOS video modes (BIOS number + 0x0100) */
-#define VIDEO_FIRST_BIOS 0x0100
-
-/* VESA BIOS video modes (VESA number + 0x0200) */
-#define VIDEO_FIRST_VESA 0x0200
-
-/* Video7 special modes (BIOS number + 0x0900) */
-#define VIDEO_FIRST_V7 0x0900
-
-# Setting of user mode (AX=mode ID) => CF=success
-
-# For now, we only handle VESA modes (0x0200..0x03ff). To handle other
-# modes, we should probably compile in the video code from the boot
-# directory.
-mode_set:
- movw %ax, %bx
- subb $VIDEO_FIRST_VESA>>8, %bh
- cmpb $2, %bh
- jb check_vesa
-
-setbad:
- clc
- ret
-
-check_vesa:
- orw $0x4000, %bx # Use linear frame buffer
- movw $0x4f02, %ax # VESA BIOS mode set call
- int $0x10
- cmpw $0x004f, %ax # AL=4f if implemented
- jnz setbad # AH=0 if OK
-
- stc
- ret
+# Copyright 2003, 2008 Pavel Machek <pavel@suse.cz>, distribute under GPLv2
.code32
ALIGN
-.org 0x800
-wakeup_stack_begin: # Stack grows down
-
-.org 0xff0 # Just below end of page
-wakeup_stack:
-ENTRY(wakeup_end)
-
-.org 0x1000
-
+ENTRY(wakeup_pmode_return)
wakeup_pmode_return:
movw $__KERNEL_DS, %ax
movw %ax, %ss
lgdt saved_gdt
lidt saved_idt
lldt saved_ldt
- ljmp $(__KERNEL_CS),$1f
+ ljmp $(__KERNEL_CS), $1f
1:
movl %cr3, %eax
movl %eax, %cr3
jne bogus_magic
# jump to place where we left off
- movl saved_eip,%eax
+ movl saved_eip, %eax
jmp *%eax
bogus_magic:
jmp bogus_magic
-##
-# acpi_copy_wakeup_routine
-#
-# Copy the above routine to low memory.
-#
-# Parameters:
-# %eax: place to copy wakeup routine to
-#
-# Returned address is location of code in low memory (past data and stack)
-#
-ENTRY(acpi_copy_wakeup_routine)
- pushl %ebx
+save_registers:
sgdt saved_gdt
sidt saved_idt
sldt saved_ldt
str saved_tss
- movl nx_enabled, %edx
- movl %edx, real_efer_save_restore - wakeup_start (%eax)
- testl $1, real_efer_save_restore - wakeup_start (%eax)
- jz 2f
- # save efer setting
- pushl %eax
- movl %eax, %ebx
- mov $0xc0000080, %ecx
- rdmsr
- movl %edx, real_save_efer_edx - wakeup_start (%ebx)
- movl %eax, real_save_efer_eax - wakeup_start (%ebx)
- popl %eax
-2:
-
- movl %cr3, %edx
- movl %edx, real_save_cr3 - wakeup_start (%eax)
- movl %cr4, %edx
- movl %edx, real_save_cr4 - wakeup_start (%eax)
- movl %cr0, %edx
- movl %edx, real_save_cr0 - wakeup_start (%eax)
- sgdt real_save_gdt - wakeup_start (%eax)
-
- movl saved_videomode, %edx
- movl %edx, video_mode - wakeup_start (%eax)
- movl acpi_realmode_flags, %edx
- movl %edx, realmode_flags - wakeup_start (%eax)
- movl $0x12345678, real_magic - wakeup_start (%eax)
- movl $0x12345678, saved_magic
- popl %ebx
- ret
-
-save_registers:
leal 4(%esp), %eax
movl %eax, saved_context_esp
- movl %ebx, saved_context_ebx
- movl %ebp, saved_context_ebp
- movl %esi, saved_context_esi
- movl %edi, saved_context_edi
- pushfl ; popl saved_context_eflags
-
- movl $ret_point, saved_eip
+ movl %ebx, saved_context_ebx
+ movl %ebp, saved_context_ebp
+ movl %esi, saved_context_esi
+ movl %edi, saved_context_edi
+ pushfl
+ popl saved_context_eflags
+
+ movl $ret_point, saved_eip
ret
restore_registers:
- movl saved_context_ebp, %ebp
- movl saved_context_ebx, %ebx
- movl saved_context_esi, %esi
- movl saved_context_edi, %edi
- pushl saved_context_eflags ; popfl
- ret
+ movl saved_context_ebp, %ebp
+ movl saved_context_ebx, %ebx
+ movl saved_context_esi, %esi
+ movl saved_context_edi, %edi
+ pushl saved_context_eflags
+ popfl
+ ret
ENTRY(do_suspend_lowlevel)
call save_processor_state
projects / linux-2.6-omap-h63xx.git / blobdiff