# SATA/PATA driver configuration
#
-menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
+menuconfig ATA
+ tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers"
depends on HAS_IOMEM
-
-config ATA
- tristate "ATA device support"
depends on BLOCK
depends on !(M32R || M68K) || BROKEN
depends on !SUN4 || BROKEN
that "speaks" the ATA protocol, also called ATA controller),
because you will be asked for it.
+ NOTE: ATA enables basic SCSI support; *however*,
+ 'SCSI disk support', 'SCSI tape support', or
+ 'SCSI CDROM support' may also be needed,
+ depending on your hardware configuration.
+
if ATA
config ATA_NONSTANDARD
depends on PCI
select PATA_SIS
help
- This option enables support for SiS Serial ATA on
+ This option enables support for SiS Serial ATA on
SiS 964/965/966/180 and Parallel ATA on SiS 180.
The PATA support for SiS 180 requires additionally to
enable the PATA_SIS driver in the config.
help
This option enables support for Initio 162x Serial ATA.
+config PATA_ACPI
+ tristate "ACPI firmware driver for PATA"
+ depends on ATA_ACPI
+ help
+ This option enables an ACPI method driver which drives
+ motherboard PATA controller interfaces through the ACPI
+ firmware in the BIOS. This driver can sometimes handle
+ otherwise unsupported hardware.
+
+config SATA_FSL
+ tristate "Freescale 3.0Gbps SATA support"
+ depends on PPC_MPC837x
+ help
+ This option enables support for Freescale 3.0Gbps SATA controller.
+ It can be found on MPC837x and MPC8315.
+
+ If unsure, say N.
+
config PATA_ALI
tristate "ALi PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
config PATA_ARTOP
- tristate "ARTOP 6210/6260 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ARTOP 6210/6260 PATA support"
+ depends on PCI
help
This option enables support for ARTOP PATA controllers.
If unsure, say N.
+config PATA_AT32
+ tristate "Atmel AVR32 PATA support (Experimental)"
+ depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
+ help
+ This option enables support for the IDE devices on the
+ Atmel AT32AP platform.
+
+ If unsure, say N.
+
config PATA_ATIIXP
- tristate "ATI PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ATI PATA support"
+ depends on PCI
help
This option enables support for the ATI ATA interfaces
found on the many ATI chipsets.
If unsure, say N.
config PATA_CMD64X
- tristate "CMD64x PATA support (Very Experimental)"
- depends on PCI&& EXPERIMENTAL
+ tristate "CMD64x PATA support"
+ depends on PCI
help
This option enables support for the CMD64x series chips
except for the CMD640.
If unsure, say N.
+config PATA_CS5536
+ tristate "CS5536 PATA support (Experimental)"
+ depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+ help
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
+
+ If unsure, say N.
+
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
config PATA_HPT366
- tristate "HPT 366/368 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 366/368 PATA support"
+ depends on PCI
help
This option enables support for the HPT 366 and 368
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT3X3
- tristate "HPT 343/363 PATA support (Experimental)"
+ tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
If unsure, say N.
+config PATA_HPT3X3_DMA
+ bool "HPT 343/363 DMA support (Experimental)"
+ depends on PATA_HPT3X3
+ help
+ This option enables DMA support for the HPT343/363
+ controllers. Enable with care as there are still some
+ problems with DMA on this chipset.
+
config PATA_ISAPNP
tristate "ISA Plug and Play PATA support (Experimental)"
depends on EXPERIMENTAL && ISAPNP
If unsure, say N.
+config PATA_NINJA32
+ tristate "Ninja32/Delkin Cardbus ATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the Ninja32, Delkin and
+ possibly other brands of Cardbus ATA adapter
+
+ If unsure, say N.
+
config PATA_NS87410
tristate "Nat Semi NS87410 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
+config PATA_NS87415
+ tristate "Nat Semi NS87415 PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the National Semiconductor
+ NS87415 PCI-IDE controller.
+
+ If unsure, say N.
+
config PATA_OPTI
tristate "OPTI621/6215 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
-endif
-endmenu
+config PATA_BF54X
+ tristate "Blackfin 54x ATAPI support"
+ depends on BF542 || BF548 || BF549
+ help
+ This option enables support for the built-in ATAPI controller on
+ Blackfin 54x family chips.
+
+ If unsure, say N.
+endif # ATA
projects / linux-2.6-omap-h63xx.git / blobdiff