[libata] AHCI: enable AHCI mode, before using AHCI reset

[linux-2.6-omap-h63xx.git] / drivers / ata / Kconfig

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 7d893a60f99420ffc9d8fe7a2b6b999dc99889b2..3a737bdce2ecc9f388721ed634f5f093b1ffe47b 100644 (file)
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -8,7 +8,6 @@ menuconfig ATA
        depends on BLOCK
        depends on !(M32R || M68K) || BROKEN
        depends on !SUN4 || BROKEN
-       depends on !(SPARC64 && !PCI)
        select SCSI
        ---help---
          If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
@@ -17,6 +16,11 @@ menuconfig ATA
          that "speaks" the ATA protocol, also called ATA controller),
          because you will be asked for it.
 
+         NOTE: ATA enables basic SCSI support; *however*,
+         'SCSI disk support', 'SCSI tape support', or
+         'SCSI CDROM support' may also be needed,
+         depending on your hardware configuration.
+
 if ATA
 
 config ATA_NONSTANDARD
@@ -188,16 +192,25 @@ config PATA_AMD
          If unsure, say N.
 
 config PATA_ARTOP
-       tristate "ARTOP 6210/6260 PATA support (Experimental)"
-       depends on PCI && EXPERIMENTAL
+       tristate "ARTOP 6210/6260 PATA support"
+       depends on PCI
        help
          This option enables support for ARTOP PATA controllers.
 
          If unsure, say N.
 
+config PATA_AT32
+       tristate "Atmel AVR32 PATA support (Experimental)"
+       depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
+       help
+         This option enables support for the IDE devices on the
+         Atmel AT32AP platform.
+
+         If unsure, say N.
+
 config PATA_ATIIXP
-       tristate "ATI PATA support (Experimental)"
-       depends on PCI && EXPERIMENTAL
+       tristate "ATI PATA support"
+       depends on PCI
        help
          This option enables support for the ATI ATA interfaces
          found on the many ATI chipsets.
@@ -215,8 +228,8 @@ config PATA_CMD640_PCI
          If unsure, say N.
 
 config PATA_CMD64X
-       tristate "CMD64x PATA support (Very Experimental)"
-       depends on PCI&& EXPERIMENTAL
+       tristate "CMD64x PATA support"
+       depends on PCI
        help
          This option enables support for the CMD64x series chips
          except for the CMD640.
@@ -278,8 +291,8 @@ config ATA_GENERIC
          If unsure, say N.
 
 config PATA_HPT366
-       tristate "HPT 366/368 PATA support (Experimental)"
-       depends on PCI && EXPERIMENTAL
+       tristate "HPT 366/368 PATA support"
+       depends on PCI
        help
          This option enables support for the HPT 366 and 368
          PATA controllers via the new ATA layer.
@@ -305,7 +318,7 @@ config PATA_HPT3X2N
          If unsure, say N.
 
 config PATA_HPT3X3
-       tristate "HPT 343/363 PATA support (Experimental)"
+       tristate "HPT 343/363 PATA support"
        depends on PCI
        help
          This option enables support for the HPT 343/363
@@ -313,6 +326,14 @@ config PATA_HPT3X3
 
          If unsure, say N.
 
+config PATA_HPT3X3_DMA
+       bool "HPT 343/363 DMA support (Experimental)"
+       depends on PATA_HPT3X3
+       help
+         This option enables DMA support for the HPT343/363
+         controllers. Enable with care as there are still some
+         problems with DMA on this chipset.
+
 config PATA_ISAPNP
        tristate "ISA Plug and Play PATA support (Experimental)"
        depends on EXPERIMENTAL && ISAPNP
@@ -584,4 +605,20 @@ config PATA_SCC
 
          If unsure, say N.
 
+config PATA_BF54X
+       tristate "Blackfin 54x ATAPI support"
+       depends on BF542 || BF548 || BF549
+       help
+         This option enables support for the built-in ATAPI controller on
+         Blackfin 54x family chips.
+
+         If unsure, say N.
+
+config PATA_BF54X_DMA
+       bool "DMA mode"
+       depends on PATA_BF54X
+       default y
+       help
+         Enable DMA mode for Blackfin ATAPI controller.
+
 endif # ATA