#include <linux/dmi.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.3.1"
+#define DRV_VERSION "0.3.2"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
u8 rev_max;
u16 flags;
} via_isa_bridges[] = {
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
+ /* Arima W730-K8/Targa Visionary 811/... */
+ if (pdev->subsystem_vendor == 0x161F && pdev->subsystem_device == 0x2032)
+ return 1;
return 0;
}
int ut;
int offset = 3 - (2*ap->port_no) - adev->devno;
-
/* Calculate the timing values we require */
ata_timing_compute(adev, mode, &t, T, UT);
ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
break;
}
+
/* Set UDMA unless device is not UDMA capable */
- if (udma_type)
- pci_write_config_byte(pdev, 0x50 + offset, ut);
+ if (udma_type) {
+ u8 cable80_status;
+
+ /* Get 80-wire cable detection bit */
+ pci_read_config_byte(pdev, 0x50 + offset, &cable80_status);
+ cable80_status &= 0x10;
+
+ pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status);
+ }
}
static void via_set_piomode(struct ata_port *ap, struct ata_device *adev)
/* Early VIA without UDMA support */
static const struct ata_port_info via_mwdma_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &via_port_ops
/* Ditto with IRQ masking required */
static const struct ata_port_info via_mwdma_info_borked = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &via_port_ops_noirq,
/* VIA UDMA 33 devices (and borked 66) */
static const struct ata_port_info via_udma33_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7,
+ .udma_mask = ATA_UDMA2,
.port_ops = &via_port_ops
};
/* VIA UDMA 66 devices */
static const struct ata_port_info via_udma66_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x1f,
+ .udma_mask = ATA_UDMA4,
.port_ops = &via_port_ops
};
/* VIA UDMA 100 devices */
static const struct ata_port_info via_udma100_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.port_ops = &via_port_ops
};
/* UDMA133 with bad AST (All current 133) */
static const struct ata_port_info via_udma133_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f, /* FIXME: should check north bridge */
+ .udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */
.port_ops = &via_port_ops
};
struct ata_port_info type;
struct pci_dev *isa = NULL;
const struct via_isa_bridge *config;
static int printed_version;
- u8 t;
u8 enable;
u32 timing;
!!(config->flags & VIA_BAD_ID),
config->id, NULL))) {
- pci_read_config_byte(isa, PCI_REVISION_ID, &t);
- if (t >= config->rev_min &&
- t <= config->rev_max)
+ if (isa->revision >= config->rev_min &&
+ isa->revision <= config->rev_max)
break;
pci_dev_put(isa);
}