#include <linux/module.h>
-#include <linux/version.h>
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/sched.h>
static int ttymajor;
static int debug_level;
static int maxframe[MAX_DEVICES];
-static int dosyncppp[MAX_DEVICES];
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
-MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
/*
* tty support and callbacks
static int chars_in_buffer(struct tty_struct *tty);
static void throttle(struct tty_struct * tty);
static void unthrottle(struct tty_struct * tty);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
/*
* generic HDLC support and callbacks
char *buf; /* virtual address of data buffer */
unsigned int pdesc; /* physical address of this descriptor */
dma_addr_t buf_dma_addr;
+ unsigned short buf_count;
};
#define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
u32 idle_mode;
u32 max_frame_size; /* as set by device config */
- unsigned int raw_rx_size;
+ unsigned int rbuf_fill_level;
unsigned int if_mode;
/* device status */
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
struct net_device *netdev;
static void tx_stop(struct slgt_info *info);
static void tx_set_idle(struct slgt_info *info);
static unsigned int free_tbuf_count(struct slgt_info *info);
+static unsigned int tbuf_bytes(struct slgt_info *info);
static void reset_tbufs(struct slgt_info *info);
static void tdma_reset(struct slgt_info *info);
static void tdma_start(struct slgt_info *info);
static int tiocmget(struct tty_struct *tty, struct file *file);
static int tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
static int get_interface(struct slgt_info *info, int __user *if_mode);
static int set_interface(struct slgt_info *info, int if_mode);
static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
int ret = 0;
struct slgt_info *info = tty->driver_data;
unsigned long flags;
+ unsigned int bufs_needed;
if (sanity_check(info, tty->name, "write"))
goto cleanup;
if (!count)
goto cleanup;
- if (info->params.mode == MGSL_MODE_RAW ||
- info->params.mode == MGSL_MODE_MONOSYNC ||
- info->params.mode == MGSL_MODE_BISYNC) {
- unsigned int bufs_needed = (count/DMABUFSIZE);
- unsigned int bufs_free = free_tbuf_count(info);
- if (count % DMABUFSIZE)
- ++bufs_needed;
- if (bufs_needed > bufs_free)
- goto cleanup;
- } else {
- if (info->tx_active)
- goto cleanup;
- if (info->tx_count) {
- /* send accumulated data from send_char() calls */
- /* as frame and wait before accepting more data. */
- tx_load(info, info->tx_buf, info->tx_count);
- goto start;
- }
+ if (!info->tx_active && info->tx_count) {
+ /* send accumulated data from send_char() */
+ tx_load(info, info->tx_buf, info->tx_count);
+ goto start;
}
+ bufs_needed = (count/DMABUFSIZE);
+ if (count % DMABUFSIZE)
+ ++bufs_needed;
+ if (bufs_needed > free_tbuf_count(info))
+ goto cleanup;
ret = info->tx_count = count;
tx_load(info, buf, count);
static int chars_in_buffer(struct tty_struct *tty)
{
struct slgt_info *info = tty->driver_data;
+ int count;
if (sanity_check(info, tty->name, "chars_in_buffer"))
return 0;
- DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
- return info->tx_count;
+ count = tbuf_bytes(info);
+ DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
+ return count;
}
/*
* set or clear transmit break condition
* break_state -1=set break condition, 0=clear
*/
-static void set_break(struct tty_struct *tty, int break_state)
+static int set_break(struct tty_struct *tty, int break_state)
{
struct slgt_info *info = tty->driver_data;
unsigned short value;
unsigned long flags;
if (sanity_check(info, tty->name, "set_break"))
- return;
+ return -EINVAL;
DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
spin_lock_irqsave(&info->lock,flags);
value &= ~BIT6;
wr_reg16(info, TCR, value);
spin_unlock_irqrestore(&info->lock,flags);
+ return 0;
}
#if SYNCLINK_GENERIC_HDLC
static int rx_enable(struct slgt_info *info, int enable)
{
unsigned long flags;
- DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
+ unsigned int rbuf_fill_level;
+ DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
spin_lock_irqsave(&info->lock,flags);
+ /*
+ * enable[31..16] = receive DMA buffer fill level
+ * 0 = noop (leave fill level unchanged)
+ * fill level must be multiple of 4 and <= buffer size
+ */
+ rbuf_fill_level = ((unsigned int)enable) >> 16;
+ if (rbuf_fill_level) {
+ if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
+ spin_unlock_irqrestore(&info->lock, flags);
+ return -EINVAL;
+ }
+ info->rbuf_fill_level = rbuf_fill_level;
+ rx_stop(info); /* restart receiver to use new fill level */
+ }
+
+ /*
+ * enable[1..0] = receiver enable command
+ * 0 = disable
+ * 1 = enable
+ * 2 = enable or force hunt mode if already enabled
+ */
+ enable &= 3;
if (enable) {
if (!info->rx_enabled)
rx_start(info);
if (info->line < MAX_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
slgt_device_count++;
info->magic = MGSL_MAGIC;
INIT_WORK(&info->task, bh_handler);
info->max_frame_size = 4096;
- info->raw_rx_size = DMABUFSIZE;
+ info->rbuf_fill_level = DMABUFSIZE;
info->port.close_delay = 5*HZ/10;
info->port.closing_wait = 30*HZ;
init_waitqueue_head(&info->status_event_wait_q);
/* set 1st descriptor address */
wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
- switch(info->params.mode) {
- case MGSL_MODE_RAW:
- case MGSL_MODE_MONOSYNC:
- case MGSL_MODE_BISYNC:
- wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
- break;
- default:
- wr_reg32(info, TDCSR, BIT0); /* DMA enable */
- }
+ wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
}
static void tx_stop(struct slgt_info *info)
* 01 enable
* 00 auto-CTS enable
*/
- val = 0;
+ val = BIT2;
switch(info->params.mode) {
case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
break;
}
+ if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
+ val |= BIT4;
if (info->signals & SerialSignal_DTR)
val |= BIT3;
if (info->signals & SerialSignal_RTS)
while(!done) {
/* reset current buffer for reuse */
info->rbufs[i].status = 0;
- switch(info->params.mode) {
- case MGSL_MODE_RAW:
- case MGSL_MODE_MONOSYNC:
- case MGSL_MODE_BISYNC:
- set_desc_count(info->rbufs[i], info->raw_rx_size);
- break;
- default:
- set_desc_count(info->rbufs[i], DMABUFSIZE);
- }
-
+ set_desc_count(info->rbufs[i], info->rbuf_fill_level);
if (i == last)
done = 1;
if (++i == info->rbuf_count)
DBGBH(("%s rx frame status=%04X size=%d\n",
info->device_name, status, framesize));
- DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
+ DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
if (framesize) {
if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
info->icount.rxok++;
while(copy_count) {
- int partial_count = min(copy_count, DMABUFSIZE);
+ int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
memcpy(p, info->rbufs[i].buf, partial_count);
p += partial_count;
copy_count -= partial_count;
return count;
}
+/*
+ * return number of bytes in unsent transmit DMA buffers
+ * and the serial controller tx FIFO
+ */
+static unsigned int tbuf_bytes(struct slgt_info *info)
+{
+ unsigned int total_count = 0;
+ unsigned int i = info->tbuf_current;
+ unsigned int reg_value;
+ unsigned int count;
+ unsigned int active_buf_count = 0;
+
+ /*
+ * Add descriptor counts for all tx DMA buffers.
+ * If count is zero (cleared by DMA controller after read),
+ * the buffer is complete or is actively being read from.
+ *
+ * Record buf_count of last buffer with zero count starting
+ * from current ring position. buf_count is mirror
+ * copy of count and is not cleared by serial controller.
+ * If DMA controller is active, that buffer is actively
+ * being read so add to total.
+ */
+ do {
+ count = desc_count(info->tbufs[i]);
+ if (count)
+ total_count += count;
+ else if (!total_count)
+ active_buf_count = info->tbufs[i].buf_count;
+ if (++i == info->tbuf_count)
+ i = 0;
+ } while (i != info->tbuf_current);
+
+ /* read tx DMA status register */
+ reg_value = rd_reg32(info, TDCSR);
+
+ /* if tx DMA active, last zero count buffer is in use */
+ if (reg_value & BIT0)
+ total_count += active_buf_count;
+
+ /* add tx FIFO count = reg_value[15..8] */
+ total_count += (reg_value >> 8) & 0xff;
+
+ /* if transmitter active add one byte for shift register */
+ if (info->tx_active)
+ total_count++;
+
+ return total_count;
+}
+
/*
* load transmit DMA buffer(s) with data
*/
set_desc_eof(*d, 0);
set_desc_count(*d, count);
+ d->buf_count = count;
}
info->tbuf_current = i;
projects / linux-2.6-omap-h63xx.git / blobdiff