I2C bus.
config I2C_PIIX4
- tristate "Intel PIIX4"
+ tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)"
depends on I2C && PCI
help
If you say yes to this option, support will be included for the Intel
PIIX4 family of mainboard I2C interfaces. Specifically, the following
- versions of the chipset are supported:
+ versions of the chipset are supported (note that Serverworks is part
+ of Broadcom):
Intel PIIX4
Intel 440MX
+ ATI IXP200
+ ATI IXP300
+ ATI IXP400
Serverworks OSB4
Serverworks CSB5
Serverworks CSB6
+ Serverworks HT-1000
SMSC Victory66
This driver can also be built as a module. If so, the module
will be called i2c-powermac.
config I2C_MPC
- tristate "MPC107/824x/85xx/52xx"
+ tristate "MPC107/824x/85xx/52xx/86xx"
depends on I2C && PPC32
help
If you say yes to this option, support will be included for the
built-in I2C interface on the MPC107/Tsi107/MPC8240/MPC8245 and
- MPC85xx family processors. The driver may also work on 52xx
+ MPC85xx/MPC8641 family processors. The driver may also work on 52xx
family processors, though interrupts are known not to work.
This driver can also be built as a module. If so, the module
This driver can also be built as a module. If so, the module
will be called i2c-nforce2.
+config I2C_OCORES
+ tristate "OpenCores I2C Controller"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes to this option, support will be included for the
+ OpenCores I2C controller. For details see
+ http://www.opencores.org/projects.cgi/web/i2c/overview
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-ocores.
+
config I2C_PARPORT
tristate "Parallel port adapter"
depends on I2C && PARPORT
This driver is a replacement for (and was inspired by) an older
driver named i2c-philips-par. The new driver supports more devices,
and makes it easier to add support for new devices.
-
+
+ An adapter type parameter is now mandatory. Please read the file
+ Documentation/i2c/busses/i2c-parport for details.
+
Another driver exists, named i2c-parport-light, which doesn't depend
on the parport driver. This is meant for embedded systems. Don't say
Y here if you intend to say Y or M there.
also be specified with a module parameter.
config SCx200_ACB
- tristate "NatSemi SCx200 ACCESS.bus"
- depends on I2C && PCI
+ tristate "Geode ACCESS.bus support"
+ depends on X86_32 && I2C && PCI
help
- Enable the use of the ACCESS.bus controllers of a SCx200 processor.
+ Enable the use of the ACCESS.bus controllers on the Geode SCx200 and
+ SC1100 processors and the CS5535 and CS5536 Geode companion devices.
If you don't know what to do here, say N.
tristate "PCA9564 on an ISA bus"
depends on I2C
select I2C_ALGOPCA
+ default n
help
This driver supports ISA boards using the Philips PCA 9564
Parallel bus to I2C bus controller
This driver can also be built as a module. If so, the module
will be called i2c-pca-isa.
+ This device is almost undetectable and using this driver on a
+ system which doesn't have this device will result in long
+ delays when I2C/SMBus chip drivers are loaded (e.g. at boot
+ time). If unsure, say N.
+
config I2C_MV64XXX
tristate "Marvell mv64xxx I2C Controller"
depends on I2C && MV64X60 && EXPERIMENTAL