# Andre Hedrick <andre@linux-ide.org>
#
+if BLOCK
+
menu "ATA/ATAPI/MFM/RLL support"
config IDE
config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA || SUPERH || IA64
+ depends on ALPHA || SUPERH || IA64 || EMBEDDED
default 4
help
This is the maximum number of IDE hardware interfaces that will
Linux. This may slow disk throughput by a few percent, but at least
things will operate 100% reliably.
-config BLK_DEV_SL82C105
- tristate "Winbond SL82c105 support"
- depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
- help
- If you have a Winbond SL82c105 IDE controller, say Y here to enable
- special configuration for this chip. This is common on various CHRP
- motherboards, but could be used elsewhere. If in doubt, say Y.
-
config BLK_DEV_IDEDMA_PCI
bool "Generic PCI bus-master DMA support"
depends on PCI && BLK_DEV_IDEPCI
ide-probe at boot. It is reported to support DVD II drives, by the
manufacturer.
+config BLK_DEV_JMICRON
+ tristate "JMicron JMB36x support"
+ help
+ Basic support for the JMicron ATA controllers. For full support
+ use the libata drivers.
+
config BLK_DEV_SC1200
tristate "National SCx200 chipset support"
help
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
-config BLK_DEV_IT8172
- bool "IT8172 IDE support"
- depends on (MIPS_ITE8172 || MIPS_IVR)
- help
- Say Y here to support the on-board IDE controller on the Integrated
- Technology Express, Inc. ITE8172 SBC. Vendor page at
- <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
- board at <http://www.mvista.com/partners/semiconductor/ite.html>.
-
config BLK_DEV_IT821X
tristate "IT821X IDE support"
help
config BLK_DEV_SGIIOC4
tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
+ select IDEPCI_SHARE_IRQ
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
chipset, which has one channel and can support two devices.
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
+config BLK_DEV_SL82C105
+ tristate "Winbond SL82c105 support"
+ depends on (PPC || ARM)
+ help
+ If you have a Winbond SL82c105 IDE controller, say Y here to enable
+ special configuration for this chip. This is common on various CHRP
+ motherboards, but could be used elsewhere. If in doubt, say Y.
+
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
int "Maximum transfer size (KB) per request (up to 128)"
default "128"
- depends BLK_DEV_IDE_AU1XXX
+ depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
endif
endmenu
+
+endif