If unsure, say Y.
config IDEDISK_MULTI_MODE
- bool "Use multi-mode by default"
- help
- If you get this error, try to say Y here:
+ bool "Use multiple sector mode for Programmed Input/Output by default"
+ help
+ This setting is irrelevant for most IDE disks, with direct memory
+ access, to which multiple sector mode does not apply. Multiple sector
+ mode is a feature of most modern IDE hard drives, permitting the
+ transfer of multiple sectors per Programmed Input/Output interrupt,
+ rather than the usual one sector per interrupt. When this feature is
+ enabled, it can reduce operating system overhead for disk Programmed
+ Input/Output. On some systems, it also can increase the data
+ throughput of Programmed Input/Output. Some drives, however, seemed
+ to run slower with multiple sector mode enabled. Some drives claimed
+ to support multiple sector mode, but lost data at some settings.
+ Under rare circumstances, such failures could result in massive
+ filesystem corruption.
+
+ If you get the following error, try to say Y here:
hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
CD-ROM drive, you can say N to all other CD-ROM options, but be sure
to say Y or M to "ISO 9660 CD-ROM file system support".
- Note that older versions of LILO (LInux LOader) cannot properly deal
- with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from
- <http://lilo.go.dyndns.org/>.
-
To compile this driver as a module, choose M here: the
module will be called ide-cd.
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- default H8300
help
If unsure, say N.
+config BLK_DEV_PLATFORM
+ tristate "Platform driver for IDE interfaces"
+ help
+ This is the platform IDE driver, used mostly for Memory Mapped
+ IDE devices, like Compact Flashes running in True IDE mode.
+
+ If unsure, say N.
+
config BLK_DEV_CMD640
- bool "CMD640 chipset bugfix/support"
+ tristate "CMD640 chipset bugfix/support"
depends on X86
---help---
The CMD-Technologies CMD640 IDE chip is used on many common 486 and
Otherwise say N.
config BLK_DEV_IDEPNP
- bool "PNP EIDE support"
+ tristate "PNP EIDE support"
depends on PNP
- select IDE_GENERIC
help
If you have a PnP (Plug and Play) compatible EIDE card and
would like the kernel to automatically detect and activate
it, say Y here.
+if PCI
+
+comment "PCI IDE chipsets support"
+
config BLK_DEV_IDEPCI
- bool "PCI IDE chipset support" if PCI
- default BLK_DEV_IDEDMA_PMAC if PPC_PMAC && BLK_DEV_IDEDMA_PMAC
- help
- Say Y here for PCI systems which use IDE drive(s).
- This option helps the IDE driver to automatically detect and
- configure all PCI-based IDE interfaces in your system.
+ bool
-config IDEPCI_SHARE_IRQ
- bool "Sharing PCI IDE interrupts support"
- depends on PCI && BLK_DEV_IDEPCI
+config IDEPCI_PCIBUS_ORDER
+ bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
+ depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ default y
help
- Some ATA/IDE chipsets have hardware support which allows for
- sharing a single IRQ with other cards. To enable support for
- this in the ATA/IDE driver, say Y here.
+ Probe IDE PCI devices in the order in which they appear on the
+ PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device)
+ instead of the order in which IDE PCI host drivers are loaded.
- It is safe to say Y to this question, in most cases.
- If unsure, say N.
+ Please note that this method of assuring stable naming of
+ IDE devices is unreliable and use other means for achieving
+ it (i.e. udev).
-config IDEPCI_PCIBUS_ORDER
- def_bool PCI && BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ If in doubt, say N.
+# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
- bool "Boot off-board chipsets first support"
- depends on PCI && BLK_DEV_IDEPCI
+ bool "Boot off-board chipsets first support (DEPRECATED)"
+ depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
help
Normally, IDE controllers built into the motherboard (on-board
controllers) are assigned to ide0 and ide1 while those on add-in PCI
Note that, if you do this, the order of the hd* devices will be
rearranged which may require modification of fstab and other files.
+ Please also note that this method of assuring stable naming of
+ IDE devices is unreliable and use other means for achieving it
+ (i.e. udev).
+
If in doubt, say N.
config BLK_DEV_GENERIC
tristate "Generic PCI IDE Chipset Support"
- depends on BLK_DEV_IDEPCI
+ select BLK_DEV_IDEPCI
help
This option provides generic support for various PCI IDE Chipsets
which otherwise might not be supported.
config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
- depends on PCI && BLK_DEV_IDEPCI && EXPERIMENTAL
+ depends on EXPERIMENTAL
+ select BLK_DEV_IDEPCI
help
This is a driver for the OPTi 82C621 EIDE controller.
Please read the comments at the top of <file:drivers/ide/pci/opti621.c>.
config BLK_DEV_RZ1000
tristate "RZ1000 chipset bugfix/support"
- depends on PCI && BLK_DEV_IDEPCI && X86
+ depends on X86
+ select BLK_DEV_IDEPCI
help
The PC-Technologies RZ1000 IDE chip is used on many common 486 and
Pentium motherboards, usually along with the "Neptune" chipset.
things will operate 100% reliably.
config BLK_DEV_IDEDMA_PCI
- bool "Generic PCI bus-master DMA support"
- depends on PCI && BLK_DEV_IDEPCI
- ---help---
- If your PCI system uses IDE drive(s) (as opposed to SCSI, say) and
- is capable of bus-master DMA operation (most Pentium PCI systems),
- you will want to say Y here to reduce CPU overhead. You can then use
- the "hdparm" utility to enable DMA for drives for which it was not
- enabled automatically. By default, DMA is not enabled automatically
- for these drives, but you can change that by saying Y to the
- following question "Use DMA by default when available". You can get
- the latest version of the hdparm utility from
- <ftp://ibiblio.org/pub/Linux/system/hardware/>.
-
- Read the comments at the beginning of <file:drivers/ide/ide-dma.c>
- and the file <file:Documentation/ide.txt> for more information.
-
- It is safe to say Y to this question.
-
-if BLK_DEV_IDEDMA_PCI
-
-config BLK_DEV_IDEDMA_FORCED
- bool "Force enable legacy 2.0.X HOSTS to use DMA"
- help
- This is an old piece of lost code from Linux 2.0 Kernels.
-
- Generally say N here.
-
-config IDEDMA_ONLYDISK
- bool "Enable DMA only for disks "
- help
- This is used if you know your ATAPI Devices are going to fail DMA
- Transfers.
-
- Generally say N here.
+ bool
+ select BLK_DEV_IDEPCI
config BLK_DEV_AEC62XX
tristate "AEC62XX chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for Acard AEC62xx (Artop ATP8xx)
IDE controllers. This allows the kernel to change PIO, DMA and UDMA
config BLK_DEV_ALI15X3
tristate "ALI M15x3 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C
onboard chipsets. It also tests for Simplex mode and enables
config BLK_DEV_AMD74XX
tristate "AMD and nVidia IDE support"
+ depends on !ARM
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for AMD-7xx and AMD-8111 chips
and also for the nVidia nForce chip. This allows the kernel to
config BLK_DEV_ATIIXP
tristate "ATI IXP chipset IDE support"
depends on X86
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for ATI IXP chipset.
This allows the kernel to change PIO, DMA and UDMA speeds
config BLK_DEV_CMD64X
tristate "CMD64{3|6|8|9} chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
Say Y here if you have an IDE controller which uses any of these
chipsets: CMD643, CMD646, or CMD648.
config BLK_DEV_TRIFLEX
tristate "Compaq Triflex IDE support"
+ select BLK_DEV_IDEDMA_PCI
help
Say Y here if you have a Compaq Triflex IDE controller, such
as those commonly found on Compaq Pentium-Pro systems
config BLK_DEV_CY82C693
tristate "CY82C693 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds detection and support for the CY82C693 chipset
used on Digital's PC-Alpha 164SX boards.
config BLK_DEV_CS5520
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
+ select BLK_DEV_IDEDMA_PCI
help
Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
5510/5520 chipset. This will automatically be detected and
config BLK_DEV_CS5530
tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
Include support for UDMA on the Cyrix MediaGX 5530 chipset. This
will automatically be detected and configured if found.
config BLK_DEV_CS5535
tristate "AMD CS5535 chipset support"
depends on X86 && !X86_64
+ select BLK_DEV_IDEDMA_PCI
help
Include support for UDMA on the NSC/AMD CS5535 companion chipset.
This will automatically be detected and configured if found.
config BLK_DEV_HPT34X
tristate "HPT34X chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds up to 4 more EIDE devices sharing a single
interrupt. The HPT343 chipset in its current form is a non-bootable
config BLK_DEV_HPT366
tristate "HPT36X/37X chipset support"
- ---help---
+ select BLK_DEV_IDEDMA_PCI
+ help
HPT366 is an Ultra DMA chipset for ATA-66.
HPT368 is an Ultra DMA chipset for ATA-66 RAID Based.
HPT370 is an Ultra DMA chipset for ATA-100.
config BLK_DEV_JMICRON
tristate "JMicron JMB36x support"
+ select BLK_DEV_IDEDMA_PCI
help
Basic support for the JMicron ATA controllers. For full support
use the libata drivers.
config BLK_DEV_SC1200
tristate "National SCx200 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
- This driver adds support for the built in IDE on the National
- SCx200 series of embedded x86 "Geode" systems
+ This driver adds support for the on-board IDE controller on the
+ National SCx200 series of embedded x86 "Geode" systems.
config BLK_DEV_PIIX
tristate "Intel PIIXn chipsets support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for Intel PIIX and ICH chips
and also for the Efar Victory66 (slc90e66) chip. This allows
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds support for the ITE 8213 IDE controller.
config BLK_DEV_IT821X
tristate "IT821X IDE support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds support for the ITE 8211 IDE controller and the
IT 8212 IDE RAID controller in both RAID and pass-through mode.
config BLK_DEV_NS87415
tristate "NS87415 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds detection and support for the NS87415 chip
(used mainly on SPARC64 and PA-RISC machines).
config BLK_DEV_PDC202XX_OLD
tristate "PROMISE PDC202{46|62|65|67} support"
+ select BLK_DEV_IDEDMA_PCI
help
Promise Ultra33 or PDC20246
Promise Ultra66 or PDC20262
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
+ select BLK_DEV_IDEDMA_PCI
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5
chipsets.
config BLK_DEV_SGIIOC4
tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
- select IDEPCI_SHARE_IRQ
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
chipset, which has one channel and can support two devices.
config BLK_DEV_SIIMAGE
tristate "Silicon Image chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds PIO/(U)DMA support for the SI CMD680 and SII
3112 (Serial ATA) chips.
config BLK_DEV_SIS5513
tristate "SiS5513 chipset support"
depends on X86
- ---help---
+ select BLK_DEV_IDEDMA_PCI
+ help
This driver ensures (U)DMA support for SIS5513 chipset family based
mainboards.
config BLK_DEV_SL82C105
tristate "Winbond SL82c105 support"
depends on (PPC || ARM)
+ select BLK_DEV_IDEDMA_PCI
help
If you have a Winbond SL82c105 IDE controller, say Y here to enable
special configuration for this chip. This is common on various CHRP
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver ensures (U)DMA support for Victory66 SouthBridges for
SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
config BLK_DEV_TRM290
tristate "Tekram TRM290 chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds support for bus master DMA transfers
using the Tekram TRM290 PCI IDE chip. Volunteers are
config BLK_DEV_VIA82CXXX
tristate "VIA82CXXX chipset support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for VIA BusMastering IDE chips.
This allows the kernel to change PIO, DMA and UDMA speeds and to
config BLK_DEV_TC86C001
tristate "Toshiba TC86C001 support"
+ select BLK_DEV_IDEDMA_PCI
help
This driver adds support for Toshiba TC86C001 GOKU-S chip.
config BLK_DEV_CELLEB
tristate "Toshiba's Cell Reference Set IDE support"
depends on PPC_CELLEB
+ select BLK_DEV_IDEDMA_PCI
help
- This driver provides support for the built-in IDE controller on
+ This driver provides support for the on-board IDE controller on
Toshiba Cell Reference Board.
If unsure, say Y.
endif
config BLK_DEV_IDE_PMAC
- bool "Builtin PowerMac IDE support"
- depends on PPC_PMAC && IDE=y
+ tristate "PowerMac on-board IDE support"
+ depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
help
- This driver provides support for the built-in IDE controller on
+ This driver provides support for the on-board IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
If unsure, say Y.
config BLK_DEV_IDE_PMAC_ATA100FIRST
- bool "Probe internal ATA/100 (Kauai) first"
+ bool "Probe on-board ATA/100 (Kauai) first"
depends on BLK_DEV_IDE_PMAC
help
This option will cause the ATA/100 controller found in UniNorth2
depends on BLK_DEV_IDE_PMAC
select BLK_DEV_IDEDMA_PCI
help
- This option allows the driver for the built-in IDE controller on
+ This option allows the driver for the on-board IDE controller on
Power Macintoshes and PowerBooks to use DMA (direct memory access)
to transfer data to and from memory. Saying Y is safe and improves
performance.
depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
- def_bool ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
- select IDE_GENERIC
+ tristate "ARM IDE support"
+ depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ default y
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
+config ETRAX_IDE
+ tristate "ETRAX IDE support"
+ depends on CRIS && BROKEN
+ select BLK_DEV_IDEDMA
+ help
+ Enables the ETRAX IDE driver.
+
+ You can't use parallel ports or SCSI ports at the same time.
+
+config ETRAX_IDE_DELAY
+ int "Delay for drives to regain consciousness"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default 15
+ help
+ Number of seconds to wait for IDE drives to spin up after an IDE
+ reset.
+
+choice
+ prompt "IDE reset pin"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default ETRAX_IDE_PB7_RESET
+
+config ETRAX_IDE_PB7_RESET
+ bool "Port_PB_Bit_7"
+ help
+ IDE reset on pin 7 on port B
+
+config ETRAX_IDE_G27_RESET
+ bool "Port_G_Bit_27"
+ help
+ IDE reset on pin 27 on port G
+
+endchoice
+
+config IDE_H8300
+ tristate "H8300 IDE support"
+ depends on H8300
+ default y
+ help
+ Enables the H8300 IDE driver.
+
config BLK_DEV_GAYLE
- bool "Amiga Gayle IDE interface support"
+ tristate "Amiga Gayle IDE interface support"
depends on AMIGA
- select IDE_GENERIC
help
This is the IDE driver for the Amiga Gayle IDE interface. It supports
both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
- This includes builtin IDE interfaces on some Amiga models (A600,
+ This includes on-board IDE interfaces on some Amiga models (A600,
A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
bus (M-Tech E-Matrix 530 expansion card).
Say Y if you have an Amiga with a Gayle IDE interface and want to use
depends on BLK_DEV_GAYLE && EXPERIMENTAL
---help---
This driver provides support for the so-called `IDE doublers' (made
- by various manufacturers, e.g. Eyetech) that can be connected to the
- builtin IDE interface of some Amiga models. Using such an IDE
- doubler, you can connect up to four instead of two IDE devices on
- the Amiga's builtin IDE interface.
+ by various manufacturers, e.g. Eyetech) that can be connected to
+ the on-board IDE interface of some Amiga models. Using such an IDE
+ doubler, you can connect up to four instead of two IDE devices to
+ the Amiga's on-board IDE interface.
Note that the normal Amiga Gayle IDE driver may not work correctly
if you have an IDE doubler and don't enable this driver!
runtime using the "ide=doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
- bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
+ tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
depends on ZORRO && EXPERIMENTAL
- select IDE_GENERIC
help
- This is the IDE driver for the IDE interfaces on the Buddha,
- Catweasel and X-Surf expansion boards. It supports up to two interfaces
- on the Buddha, three on the Catweasel and two on the X-Surf.
+ This is the IDE driver for the IDE interfaces on the Buddha, Catweasel
+ and X-Surf expansion boards. It supports up to two interfaces on the
+ Buddha, three on the Catweasel and two on the X-Surf.
Say Y if you have a Buddha or Catweasel expansion board and want to
use IDE devices (hard disks, CD-ROM drives, etc.) that are connected
to one of its IDE interfaces.
config BLK_DEV_FALCON_IDE
- bool "Falcon IDE interface support"
+ tristate "Falcon IDE interface support"
depends on ATARI
- select IDE_GENERIC
help
- This is the IDE driver for the builtin IDE interface on the Atari
+ This is the IDE driver for the on-board IDE interface on the Atari
Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
- disks, CD-ROM drives, etc.) that are connected to the builtin IDE
+ disks, CD-ROM drives, etc.) that are connected to the on-board IDE
interface.
config BLK_DEV_MAC_IDE
- bool "Macintosh Quadra/Powerbook IDE interface support"
+ tristate "Macintosh Quadra/Powerbook IDE interface support"
depends on MAC
- select IDE_GENERIC
help
- This is the IDE driver for the builtin IDE interface on some m68k
+ This is the IDE driver for the on-board IDE interface on some m68k
Macintosh models. It supports both the `Quadra style' (used in
Quadra/ Centris 630 and Performa 588 models) and `Powerbook style'
(used in the Powerbook 150 and 190 models) IDE interface.
Say Y if you have such an Macintosh model and want to use IDE
devices (hard disks, CD-ROM drives, etc.) that are connected to the
- builtin IDE interface.
+ on-board IDE interface.
config BLK_DEV_Q40IDE
- bool "Q40/Q60 IDE interface support"
+ tristate "Q40/Q60 IDE interface support"
depends on Q40
- select IDE_GENERIC
help
Enable the on-board IDE controller in the Q40/Q60. This should
normally be on; disable it only if you are running a custom hard
drive subsystem through an expansion card.
config BLK_DEV_MPC8xx_IDE
- bool "MPC8xx IDE support"
- depends on 8xx && IDE=y && BLK_DEV_IDE=y
- select IDE_GENERIC
+ tristate "MPC8xx IDE support"
+ depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
endchoice
# no isa -> no vlb
-config IDE_CHIPSETS
- bool "Other IDE chipset support"
- depends on ISA
- ---help---
- Say Y here if you want to include enhanced support for various IDE
- interface chipsets used on motherboards and add-on cards. You can
- then pick your particular IDE chip from among the following options.
- This enhanced support may be necessary for Linux to be able to
- access the 3rd/4th drives in some systems. It may also enable
- setting of higher speed I/O rates to improve system performance with
- these chipsets. Most of these also require special kernel boot
- parameters to actually turn on the support at runtime; you can find
- a list of these in the file <file:Documentation/ide.txt>.
-
- People with SCSI-only systems can say N here.
-
-if IDE_CHIPSETS
+if ISA
+comment "Other IDE chipsets support"
comment "Note: most of these also require special kernel boot parameters"
config BLK_DEV_4DRIVES
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
- <file:Documentation/ide.txt> and <file:drivers/ide/legacy/ali14xx.c> for
- more info.
+ <file:Documentation/ide.txt> and <file:drivers/ide/legacy/ali14xx.c>
+ for more info.
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
- <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
- more info.
+ <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
+ for more info.
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
-config IDEDMA_IVB
- bool "IGNORE word93 Validation BITS"
- depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
- ---help---
- There are unclear terms in ATA-4 and ATA-5 standards how certain
- hardware (an 80c ribbon) should be detected. Different interpretations
- of the standards have been released in hardware. This causes problems:
- for example, a host with Ultra Mode 4 (or higher) will not run
- in that mode with an 80c ribbon.
-
- If you are experiencing compatibility or performance problems, you
- MAY try to answer Y here. However, it does not necessarily solve
- any of your problems, it could even cause more of them.
-
- It is normally safe to answer Y; however, the default is N.
+config IDE_ARCH_OBSOLETE_INIT
+ def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC
endif
projects / linux-2.6-omap-h63xx.git / blobdiff