[SCSI] mptfusion: Increase scsi-timeouts, similariy to the LSI 4.x driver.

[linux-2.6-omap-h63xx.git] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 8e93a797c93de9c8eaf35e28573a6e81dc18dda3..74a369a6116fc7fbeb7bea0c68c629ec4cfb1102 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -4,7 +4,7 @@
 
 # Select HAVE_IDE if IDE is supported
 config HAVE_IDE
-       def_bool n
+       bool
 
 menuconfig IDE
        tristate "ATA/ATAPI/MFM/RLL support"
@@ -54,38 +54,6 @@ menuconfig IDE
 
 if IDE
 
-config BLK_DEV_IDE
-       tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
-       ---help---
-         If you say Y here, you will use the full-featured IDE driver to
-         control up to ten ATA/IDE interfaces, each being able to serve a
-         "master" and a "slave" device, for a total of up to twenty ATA/IDE
-         disk/cdrom/tape/floppy drives.
-
-         Useful information about large (>540 MB) IDE disks, multiple
-         interfaces, what to do if ATA/IDE devices are not automatically
-         detected, sound card ATA/IDE ports, module support, and other
-         topics, is contained in <file:Documentation/ide/ide.txt>. For detailed
-         information about hard drives, consult the Disk-HOWTO and the
-         Multi-Disk-HOWTO, available from
-         <http://www.tldp.org/docs.html#howto>.
-
-         To fine-tune ATA/IDE drive/interface parameters for improved
-         performance, look for the hdparm package at
-         <ftp://ibiblio.org/pub/Linux/system/hardware/>.
-
-         To compile this driver as a module, choose M here and read
-         <file:Documentation/ide/ide.txt>. The module will be called ide-mod.
-         Do not compile this driver as a module if your root file system (the
-         one containing the directory /) is located on an IDE device.
-
-         If you have one or more IDE drives, say Y or M here. If your system
-         has no IDE drives, or if memory requirements are really tight, you
-         could say N here, and select the "Old hard disk driver" below
-         instead to save about 13 KB of memory in the kernel.
-
-if BLK_DEV_IDE
-
 comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
 
 config IDE_TIMINGS
@@ -131,29 +99,6 @@ config BLK_DEV_IDEDISK
 
          If unsure, say Y.
 
-config IDEDISK_MULTI_MODE
-       bool "Use multiple sector mode for Programmed Input/Output by default"
-       help
-         This setting is irrelevant for most IDE disks, with direct memory
-         access, to which multiple sector mode does not apply. Multiple sector
-         mode is a feature of most modern IDE hard drives, permitting the
-         transfer of multiple sectors per Programmed Input/Output interrupt,
-         rather than the usual one sector per interrupt. When this feature is
-         enabled, it can reduce operating system overhead for disk Programmed
-         Input/Output. On some systems, it also can increase the data
-         throughput of Programmed Input/Output. Some drives, however, seemed
-         to run slower with multiple sector mode enabled. Some drives claimed
-         to support multiple sector mode, but lost data at some settings.
-         Under rare circumstances, such failures could result in massive
-         filesystem corruption.
-
-         If you get the following error, try to say Y here:
-
-         hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
-         hda: set_multmode: error=0x04 { DriveStatusError }
-
-         If in doubt, say N.
-
 config BLK_DEV_IDECS
        tristate "PCMCIA IDE support"
        depends on PCMCIA
@@ -371,7 +316,7 @@ config BLK_DEV_IDEPCI
 
 config IDEPCI_PCIBUS_ORDER
        bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
-       depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+       depends on IDE=y && BLK_DEV_IDEPCI
        default y
        help
          Probe IDE PCI devices in the order in which they appear on the
@@ -752,7 +697,7 @@ endif
 
 config BLK_DEV_IDE_PMAC
        tristate "PowerMac on-board IDE support"
-       depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
+       depends on PPC_PMAC && IDE=y
        select IDE_TIMINGS
        help
          This driver provides support for the on-board IDE controller on
@@ -780,10 +725,6 @@ config BLK_DEV_IDEDMA_PMAC
          to transfer data to and from memory.  Saying Y is safe and improves
          performance.
 
-config BLK_DEV_IDE_SWARM
-       tristate "IDE for Sibyte evaluation boards"
-       depends on SIBYTE_SB1xxx_SOC
-
 config BLK_DEV_IDE_AU1XXX
        bool "IDE for AMD Alchemy Au1200"
        depends on SOC_AU1200
@@ -990,6 +931,4 @@ config BLK_DEV_IDEDMA
        def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
                 BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 
-endif
-
 endif # IDE