V4L/DVB (7641): V4L: ov511 - use usb_interface as parent, not usb_device

[linux-2.6-omap-h63xx.git] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index eed6d8e1b5c7abfbff3d693bc072bb3040ea3e1e..87532034d10571818f50d03ff891a6f68b11f17c 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -122,24 +122,6 @@ config BLK_DEV_IDE_SATA
 
          If unsure, say N.
 
-config BLK_DEV_HD_IDE
-       bool "Use old disk-only driver on primary interface"
-       depends on (X86 || SH_MPC1211)
-       ---help---
-         There are two drivers for MFM/RLL/IDE disks.  Most people use just
-         the new enhanced driver by itself.  This option however installs the
-         old hard disk driver to control the primary IDE/disk interface in
-         the system, leaving the new enhanced IDE driver to take care of only
-         the 2nd/3rd/4th IDE interfaces.  Doing this will prevent you from
-         having an IDE/ATAPI CD-ROM or tape drive connected to the primary
-         IDE interface.  Choosing this option may be useful for older systems
-         which have MFM/RLL/ESDI controller+drives at the primary port
-         address (0x1f0), along with IDE drives at the secondary/3rd/4th port
-         addresses.
-
-         Normally, just say N here; you will then use the new driver for all
-         4 interfaces.
-
 config BLK_DEV_IDEDISK
        tristate "Include IDE/ATA-2 DISK support"
        ---help---
@@ -325,6 +307,7 @@ comment "IDE chipset support/bugfixes"
 
 config IDE_GENERIC
        tristate "generic/default IDE chipset support"
+       depends on ALPHA || X86 || IA64 || M32R || MIPS || PPC32
        help
          If unsure, say N.
 
@@ -416,12 +399,6 @@ config BLK_DEV_OFFBOARD
          This can improve the usability of some boot managers such as lilo
          when booting from a drive on an off-board controller.
 
-         If you say Y here, and you actually want to reverse the device scan
-         order as explained above, you also need to issue the kernel command
-         line option "ide=reverse". (Try "man bootparam" or see the
-         documentation of your boot loader (lilo or loadlin) about how to
-         pass options to the kernel at boot time.)
-
          Note that, if you do this, the order of the hd* devices will be
          rearranged which may require modification of fstab and other files.
 
@@ -615,8 +592,7 @@ config BLK_DEV_HPT366
          reference to device 0x80. The other solution is to say Y to "Boot
          off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless
          your mother board has the chipset natively mounted. Regardless one
-         should use the fore mentioned option and call at LILO or include
-         "ide=reverse" in LILO's append-line.
+         should use the fore mentioned option and call at LILO.
 
          This driver requires dynamic tuning of the chipset during the
          ide-probe at boot. It is reported to support DVD II drives, by the
@@ -1049,7 +1025,7 @@ config IDE_EXT_DIRECT
 endchoice
 
 # no isa -> no vlb
-if ISA
+if ISA && (ALPHA || X86 || MIPS)
 
 comment "Other IDE chipsets support"
 comment "Note: most of these also require special kernel boot parameters"
@@ -1060,8 +1036,8 @@ config BLK_DEV_4DRIVES
          Certain older chipsets, including the Tekram 690CD, use a single set
          of I/O ports at 0x1f0 to control up to four drives, instead of the
          customary two drives per port. Support for this can be enabled at
-         runtime using the "ide0=four" kernel boot parameter if you say Y
-         here.
+         runtime using the "ide-4drives.probe" kernel boot parameter if you
+         say Y here.
 
 config BLK_DEV_ALI14XX
        tristate "ALI M14xx support"
@@ -1114,14 +1090,10 @@ config BLK_DEV_IDEDMA
        def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
                 BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 
-config IDE_ARCH_OBSOLETE_INIT
-       def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC
-
 endif
 
 config BLK_DEV_HD_ONLY
        bool "Old hard disk (MFM/RLL/IDE) driver"
-       depends on BLK_DEV_IDE=n
        help
          There are two drivers for MFM/RLL/IDE hard disks. Most people use
          the newer enhanced driver, but this old one is still around for two
@@ -1133,12 +1105,16 @@ config BLK_DEV_HD_ONLY
          for systems with only older MFM/RLL/ESDI drives. Choosing the old
          driver can save 13 KB or so of kernel memory.
 
+         If you want to use this driver together with the new one you have
+         to use "hda=noprobe hdb=noprobe" kernel parameters to prevent the new
+         driver from probing the primary interface.
+
          If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
          instead of this one. For more detailed information, read the
          Disk-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.
 
 config BLK_DEV_HD
-       def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY
+       def_bool BLK_DEV_HD_ONLY
 
 endif # IDE