# Andre Hedrick <andre@linux-ide.org>
#
+if BLOCK
+
menu "ATA/ATAPI/MFM/RLL support"
config IDE
if IDE
-config IDE_MAX_HWIFS
+config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA || SUPERH
+ depends on ALPHA || SUPERH || IA64 || EMBEDDED
default 4
help
This is the maximum number of IDE hardware interfaces that will
tristate "PCMCIA IDE support"
depends on PCMCIA
help
- Support for outboard IDE disks, tape drives, and CD-ROM drives
- connected through a PCMCIA card.
+ Support for Compact Flash cards, outboard IDE disks, tape drives,
+ and CD-ROM drives connected through a PCMCIA card.
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
help
This is a direct raw access to the media. It is a complex but
elegant solution to test and validate the domain of the hardware and
- perform below the driver data recover if needed. This is the most
+ perform below the driver data recovery if needed. This is the most
basic form of media-forensics.
If you are unsure, say N here.
Linux. This may slow disk throughput by a few percent, but at least
things will operate 100% reliably.
-config BLK_DEV_SL82C105
- tristate "Winbond SL82c105 support"
- depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
- help
- If you have a Winbond SL82c105 IDE controller, say Y here to enable
- special configuration for this chip. This is common on various CHRP
- motherboards, but could be used elsewhere. If in doubt, say Y.
-
config BLK_DEV_IDEDMA_PCI
bool "Generic PCI bus-master DMA support"
depends on PCI && BLK_DEV_IDEPCI
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
help
- Include support for PIO tuning an virtual DMA on the Cyrix MediaGX
+ Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
5510/5520 chipset. This will automatically be detected and
configured if found.
ide-probe at boot. It is reported to support DVD II drives, by the
manufacturer.
+config BLK_DEV_JMICRON
+ tristate "JMicron JMB36x support"
+ help
+ Basic support for the JMicron ATA controllers. For full support
+ use the libata drivers.
+
config BLK_DEV_SC1200
tristate "National SCx200 chipset support"
help
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
-config BLK_DEV_IT8172
- bool "IT8172 IDE support"
- depends on (MIPS_ITE8172 || MIPS_IVR)
- help
- Say Y here to support the on-board IDE controller on the Integrated
- Technology Express, Inc. ITE8172 SBC. Vendor page at
- <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
- board at <http://www.mvista.com/partners/semiconductor/ite.html>.
-
config BLK_DEV_IT821X
tristate "IT821X IDE support"
help
It was originally designed for the PDC20246/Ultra33, whose BIOS will
only setup UDMA on the first two PDC20246 cards. It has also been
- used succesfully on a PDC20265/Ultra100, allowing use of UDMA modes
+ used successfully on a PDC20265/Ultra100, allowing use of UDMA modes
when the PDC20265 BIOS has been disabled (for faster boot up).
Please read the comments at the top of
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
-# FIXME - probably wants to be one for old and for new
-config PDC202XX_FORCE
- bool "Enable controller even if disabled by BIOS"
- depends on BLK_DEV_PDC202XX_NEW
- help
- Enable the PDC202xx controller even if it has been disabled in the BIOS setup.
-
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
help
config BLK_DEV_SGIIOC4
tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
+ select IDEPCI_SHARE_IRQ
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
chipset, which has one channel and can support two devices.
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
+config BLK_DEV_SL82C105
+ tristate "Winbond SL82c105 support"
+ depends on (PPC || ARM)
+ help
+ If you have a Winbond SL82c105 IDE controller, say Y here to enable
+ special configuration for this chip. This is common on various CHRP
+ motherboards, but could be used elsewhere. If in doubt, say Y.
+
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
- This driver ensures (U)DMA support for Victroy66 SouthBridges for
+ This driver ensures (U)DMA support for Victory66 SouthBridges for
SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
The nice thing about it is that you can mix Ultra/DMA/PIO devices
and it will handle timing cycles. Since this is an improved
to transfer data to and from memory. Saying Y is safe and improves
performance.
-config BLK_DEV_IDE_PMAC_BLINK
- bool "Blink laptop LED on drive activity"
- depends on BLK_DEV_IDE_PMAC && ADB_PMU
- help
- This option enables the use of the sleep LED as a hard drive
- activity LED.
-
config BLK_DEV_IDE_SWARM
tristate "IDE for Sibyte evaluation boards"
depends on SIBYTE_SB1xxx_SOC
config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
int "Maximum transfer size (KB) per request (up to 128)"
default "128"
- depends BLK_DEV_IDE_AU1XXX
+ depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
in that mode with an 80c ribbon.
If you are experiencing compatibility or performance problems, you
- MAY try to answering Y here. However, it does not necessarily solve
+ MAY try to answer Y here. However, it does not necessarily solve
any of your problems, it could even cause more of them.
It is normally safe to answer Y; however, the default is N.
endif
endmenu
+
+endif