ide-{floppy,tape}: remove debug code for dumping identify data

[linux-2.6-omap-h63xx.git] / drivers / ide / ide-floppy.c

diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index ff8232ef96598ae784001a0a61dd2da69a91c69a..cf48b4a46d6d6536aa153515a291dd20a4460539 100644 (file)
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -1658,7 +1658,6 @@ static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
 {
        struct idefloppy_id_gcw gcw;
 #if IDEFLOPPY_DEBUG_INFO
-       u16 mask,i;
        char buffer[80];
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
@@ -1705,55 +1704,6 @@ static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
                default: sprintf(buffer, "Reserved");break;
        }
        printk(KERN_INFO "Command Packet Size: %s\n", buffer);
-       printk(KERN_INFO "Model: %.40s\n",id->model);
-       printk(KERN_INFO "Firmware Revision: %.8s\n",id->fw_rev);
-       printk(KERN_INFO "Serial Number: %.20s\n",id->serial_no);
-       printk(KERN_INFO "Write buffer size(?): %d bytes\n",id->buf_size*512);
-       printk(KERN_INFO "DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
-       printk(KERN_INFO "LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
-       printk(KERN_INFO "IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
-       printk(KERN_INFO "IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
-       printk(KERN_INFO "ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
-       printk(KERN_INFO "PIO Cycle Timing Category: %d\n",id->tPIO);
-       printk(KERN_INFO "DMA Cycle Timing Category: %d\n",id->tDMA);
-       printk(KERN_INFO "Single Word DMA supported modes:\n");
-       for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-               if (id->dma_1word & mask)
-                       printk(KERN_INFO "   Mode %d%s\n", i,
-                       (id->dma_1word & (mask << 8)) ? " (active)" : "");
-       }
-       printk(KERN_INFO "Multi Word DMA supported modes:\n");
-       for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-               if (id->dma_mword & mask)
-                       printk(KERN_INFO "   Mode %d%s\n", i,
-                       (id->dma_mword & (mask << 8)) ? " (active)" : "");
-       }
-       if (id->field_valid & 0x0002) {
-               printk(KERN_INFO "Enhanced PIO Modes: %s\n",
-                       id->eide_pio_modes & 1 ? "Mode 3":"None");
-               if (id->eide_dma_min == 0)
-                       sprintf(buffer, "Not supported");
-               else
-                       sprintf(buffer, "%d ns",id->eide_dma_min);
-               printk(KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n", buffer);
-               if (id->eide_dma_time == 0)
-                       sprintf(buffer, "Not supported");
-               else
-                       sprintf(buffer, "%d ns",id->eide_dma_time);
-               printk(KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n", buffer);
-               if (id->eide_pio == 0)
-                       sprintf(buffer, "Not supported");
-               else
-                       sprintf(buffer, "%d ns",id->eide_pio);
-               printk(KERN_INFO "Minimum PIO cycle without IORDY: %s\n",
-                       buffer);
-               if (id->eide_pio_iordy == 0)
-                       sprintf(buffer, "Not supported");
-               else
-                       sprintf(buffer, "%d ns",id->eide_pio_iordy);
-               printk(KERN_INFO "Minimum PIO cycle with IORDY: %s\n", buffer);
-       } else
-               printk(KERN_INFO "According to the device, fields 64-70 are not valid.\n");
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
        if (gcw.protocol != 2)