/*
- * linux/drivers/ide/pci/hpt366.c Version 1.10 Jun 29, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.20 Oct 1, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2007 Bartlomiej Zolnierkiewicz
* Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
*
* Thanks to HighPoint Technologies for their assistance, and hardware.
* HPT37x chip family; save space by introducing the separate transfer mode
* table in which the mode lookup is done
* - use f_CNT value saved by the HighPoint BIOS as reading it directly gives
- * the wrong PCI frequency since DPLL has already been calibrated by BIOS
+ * the wrong PCI frequency since DPLL has already been calibrated by BIOS;
+ * read it only from the function 0 of HPT374 chips
* - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
* and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
* - pass to init_chipset() handlers a copy of the IDE PCI device structure as
* unify HPT36x/37x timing setup code and the speedproc handlers by joining
* the register setting lists into the table indexed by the clock selected
* - set the correct hwif->ultra_mask for each individual chip
+ * - add Ultra and MW DMA mode filtering for the HPT37[24] based SATA cards
* Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com>
*/
*/
struct hpt_info {
+ char *chip_name; /* Chip name */
u8 chip_type; /* Chip type */
- u8 max_ultra; /* Max. UltraDMA mode allowed */
+ u8 udma_mask; /* Allowed UltraDMA modes mask. */
u8 dpll_clk; /* DPLL clock in MHz */
u8 pci_clk; /* PCI clock in MHz */
u32 **settings; /* Chipset settings table */
};
static struct hpt_info hpt36x __devinitdata = {
+ .chip_name = "HPT36x",
.chip_type = HPT36x,
- .max_ultra = HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ? 4 : 3) : 2,
+ .udma_mask = HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ? ATA_UDMA4 : ATA_UDMA3) : ATA_UDMA2,
.dpll_clk = 0, /* no DPLL */
.settings = hpt36x_settings
};
static struct hpt_info hpt370 __devinitdata = {
+ .chip_name = "HPT370",
.chip_type = HPT370,
- .max_ultra = HPT370_ALLOW_ATA100_5 ? 5 : 4,
+ .udma_mask = HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt370a __devinitdata = {
+ .chip_name = "HPT370A",
.chip_type = HPT370A,
- .max_ultra = HPT370_ALLOW_ATA100_5 ? 5 : 4,
+ .udma_mask = HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt374 __devinitdata = {
+ .chip_name = "HPT374",
.chip_type = HPT374,
- .max_ultra = 5,
+ .udma_mask = ATA_UDMA5,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt372 __devinitdata = {
+ .chip_name = "HPT372",
.chip_type = HPT372,
- .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 55,
.settings = hpt37x_settings
};
static struct hpt_info hpt372a __devinitdata = {
+ .chip_name = "HPT372A",
.chip_type = HPT372A,
- .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt302 __devinitdata = {
+ .chip_name = "HPT302",
.chip_type = HPT302,
- .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt371 __devinitdata = {
+ .chip_name = "HPT371",
.chip_type = HPT371,
- .max_ultra = HPT371_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt372n __devinitdata = {
+ .chip_name = "HPT372N",
.chip_type = HPT372N,
- .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
static struct hpt_info hpt302n __devinitdata = {
+ .chip_name = "HPT302N",
.chip_type = HPT302N,
- .max_ultra = HPT302_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
static struct hpt_info hpt371n __devinitdata = {
+ .chip_name = "HPT371N",
.chip_type = HPT371N,
- .max_ultra = HPT371_ALLOW_ATA133_6 ? 6 : 5,
+ .udma_mask = HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
}
/*
- * Note for the future; the SATA hpt37x we must set
- * either PIO or UDMA modes 0,4,5
+ * The Marvell bridge chips used on the HighPoint SATA cards do not seem
+ * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
*/
static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
- struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
- u8 mask;
+ ide_hwif_t *hwif = HWIF(drive);
+ struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
+ u8 mask = hwif->ultra_mask;
switch (info->chip_type) {
- case HPT370A:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- return 0x1f;
- else
- return 0x3f;
- case HPT370:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- mask = 0x1f;
- else
- mask = 0x3f;
- break;
case HPT36x:
if (!HPT366_ALLOW_ATA66_4 ||
check_in_drive_list(drive, bad_ata66_4))
- mask = 0x0f;
- else
- mask = 0x1f;
+ mask = ATA_UDMA3;
if (!HPT366_ALLOW_ATA66_3 ||
check_in_drive_list(drive, bad_ata66_3))
- mask = 0x07;
+ mask = ATA_UDMA2;
break;
+ case HPT370:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ mask = ATA_UDMA4;
+ break;
+ case HPT370A:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ return ATA_UDMA4;
+ case HPT372 :
+ case HPT372A:
+ case HPT372N:
+ case HPT374 :
+ if (ide_dev_is_sata(drive->id))
+ mask &= ~0x0e;
+ /* Fall thru */
default:
- return 0x7f;
+ return mask;
}
return check_in_drive_list(drive, bad_ata33) ? 0x00 : mask;
}
+static u8 hpt3xx_mdma_filter(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = HWIF(drive);
+ struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
+
+ switch (info->chip_type) {
+ case HPT372 :
+ case HPT372A:
+ case HPT372N:
+ case HPT374 :
+ if (ide_dev_is_sata(drive->id))
+ return 0x00;
+ /* Fall thru */
+ default:
+ return 0x07;
+ }
+}
+
static u32 get_speed_setting(u8 speed, struct hpt_info *info)
{
int i;
return (*info->settings)[i];
}
-static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
+static void hpt36x_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = pci_get_drvdata(dev);
- u8 speed = ide_rate_filter(drive, xferspeed);
u8 itr_addr = drive->dn ? 0x44 : 0x40;
u32 old_itr = 0;
u32 itr_mask, new_itr;
- /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
- if (drive->media != ide_disk)
- speed = min_t(u8, speed, XFER_PIO_4);
-
itr_mask = speed < XFER_MW_DMA_0 ? 0x30070000 :
(speed < XFER_UDMA_0 ? 0xc0070000 : 0xc03800ff);
new_itr &= ~0xc0000000;
pci_write_config_dword(dev, itr_addr, new_itr);
-
- return ide_config_drive_speed(drive, speed);
}
-static int hpt37x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
+static void hpt37x_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = pci_get_drvdata(dev);
- u8 speed = ide_rate_filter(drive, xferspeed);
u8 itr_addr = 0x40 + (drive->dn * 4);
u32 old_itr = 0;
u32 itr_mask, new_itr;
- /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
- if (drive->media != ide_disk)
- speed = min_t(u8, speed, XFER_PIO_4);
-
itr_mask = speed < XFER_MW_DMA_0 ? 0x303c0000 :
(speed < XFER_UDMA_0 ? 0xc03c0000 : 0xc1c001ff);
if (speed < XFER_MW_DMA_0)
new_itr &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
pci_write_config_dword(dev, itr_addr, new_itr);
-
- return ide_config_drive_speed(drive, speed);
}
-static int hpt3xx_tune_chipset(ide_drive_t *drive, u8 speed)
+static void hpt3xx_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
if (info->chip_type >= HPT370)
- return hpt37x_tune_chipset(drive, speed);
+ hpt37x_set_mode(drive, speed);
else /* hpt368: hpt_minimum_revision(dev, 2) */
- return hpt36x_tune_chipset(drive, speed);
+ hpt36x_set_mode(drive, speed);
}
-static void hpt3xx_tune_drive(ide_drive_t *drive, u8 pio)
+static void hpt3xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
- (void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
+ hpt3xx_set_mode(drive, XFER_PIO_0 + pio);
}
static int hpt3xx_quirkproc(ide_drive_t *drive)
static void hpt3xx_intrproc(ide_drive_t *drive)
{
- ide_hwif_t *hwif = HWIF(drive);
-
if (drive->quirk_list)
return;
+
/* drives in the quirk_list may not like intr setups/cleanups */
- hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
+ outb(drive->ctl | 2, IDE_CONTROL_REG);
}
static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
enable_irq (hwif->irq);
}
} else
- hwif->OUTB(mask ? (drive->ctl | 2) : (drive->ctl & ~2),
- IDE_CONTROL_REG);
-}
-
-static int hpt366_config_drive_xfer_rate(ide_drive_t *drive)
-{
- drive->init_speed = 0;
-
- if (ide_tune_dma(drive))
- return 0;
-
- if (ide_use_fast_pio(drive))
- hpt3xx_tune_drive(drive, 255);
-
- return -1;
+ outb(mask ? (drive->ctl | 2) : (drive->ctl & ~2),
+ IDE_CONTROL_REG);
}
/*
printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo & 0x1ff);
/* get DMA command mode */
- dma_cmd = hwif->INB(hwif->dma_command);
+ dma_cmd = inb(hwif->dma_command);
/* stop DMA */
- hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command);
+ outb(dma_cmd & ~0x1, hwif->dma_command);
hpt370_clear_engine(drive);
}
static int hpt370_ide_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- u8 dma_stat = hwif->INB(hwif->dma_status);
+ u8 dma_stat = inb(hwif->dma_status);
if (dma_stat & 0x01) {
/* wait a little */
udelay(20);
- dma_stat = hwif->INB(hwif->dma_status);
+ dma_stat = inb(hwif->dma_status);
if (dma_stat & 0x01)
hpt370_irq_timeout(drive);
}
static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode)
{
- u8 scr2 = hwif->INB(hwif->dma_master + 0x7b);
+ u8 scr2 = inb(hwif->dma_master + 0x7b);
if ((scr2 & 0x7f) == mode)
return;
/* Tristate the bus */
- hwif->OUTB(0x80, hwif->dma_master + 0x73);
- hwif->OUTB(0x80, hwif->dma_master + 0x77);
+ outb(0x80, hwif->dma_master + 0x73);
+ outb(0x80, hwif->dma_master + 0x77);
/* Switch clock and reset channels */
- hwif->OUTB(mode, hwif->dma_master + 0x7b);
- hwif->OUTB(0xc0, hwif->dma_master + 0x79);
+ outb(mode, hwif->dma_master + 0x7b);
+ outb(0xc0, hwif->dma_master + 0x79);
/*
* Reset the state machines.
* NOTE: avoid accidentally enabling the disabled channels.
*/
- hwif->OUTB(hwif->INB(hwif->dma_master + 0x70) | 0x32,
- hwif->dma_master + 0x70);
- hwif->OUTB(hwif->INB(hwif->dma_master + 0x74) | 0x32,
- hwif->dma_master + 0x74);
+ outb(inb(hwif->dma_master + 0x70) | 0x32, hwif->dma_master + 0x70);
+ outb(inb(hwif->dma_master + 0x74) | 0x32, hwif->dma_master + 0x74);
/* Complete reset */
- hwif->OUTB(0x00, hwif->dma_master + 0x79);
+ outb(0x00, hwif->dma_master + 0x79);
/* Reconnect channels to bus */
- hwif->OUTB(0x00, hwif->dma_master + 0x73);
- hwif->OUTB(0x00, hwif->dma_master + 0x77);
+ outb(0x00, hwif->dma_master + 0x73);
+ outb(0x00, hwif->dma_master + 0x77);
}
/**
struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
unsigned long io_base = pci_resource_start(dev, 4);
u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
+ u8 chip_type;
enum ata_clock clock;
if (info == NULL) {
* Copy everything from a static "template" structure
* to just allocated per-chip hpt_info structure.
*/
- *info = *(struct hpt_info *)pci_get_drvdata(dev);
+ memcpy(info, pci_get_drvdata(dev), sizeof(struct hpt_info));
+ chip_type = info->chip_type;
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
/*
* First, try to estimate the PCI clock frequency...
*/
- if (info->chip_type >= HPT370) {
+ if (chip_type >= HPT370) {
u8 scr1 = 0;
u16 f_cnt = 0;
u32 temp = 0;
* HighPoint does this for HPT372A.
* NOTE: This register is only writeable via I/O space.
*/
- if (info->chip_type == HPT372A)
+ if (chip_type == HPT372A)
outb(0x0e, io_base + 0x9c);
/*
* First try reading the register in which the HighPoint BIOS
* saves f_CNT value before reprogramming the DPLL from its
* default setting (which differs for the various chips).
- * NOTE: This register is only accessible via I/O space.
*
- * In case the signature check fails, we'll have to resort to
- * reading the f_CNT register itself in hopes that nobody has
- * touched the DPLL yet...
+ * NOTE: This register is only accessible via I/O space;
+ * HPT374 BIOS only saves it for the function 0, so we have to
+ * always read it from there -- no need to check the result of
+ * pci_get_slot() for the function 0 as the whole device has
+ * been already "pinned" (via function 1) in init_setup_hpt374()
+ */
+ if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
+ struct pci_dev *dev1 = pci_get_slot(dev->bus,
+ dev->devfn - 1);
+ unsigned long io_base = pci_resource_start(dev1, 4);
+
+ temp = inl(io_base + 0x90);
+ pci_dev_put(dev1);
+ } else
+ temp = inl(io_base + 0x90);
+
+ /*
+ * In case the signature check fails, we'll have to
+ * resort to reading the f_CNT register itself in hopes
+ * that nobody has touched the DPLL yet...
*/
- temp = inl(io_base + 0x90);
if ((temp & 0xFFFFF000) != 0xABCDE000) {
int i;
* We also don't like using the DPLL because this causes glitches
* on PRST-/SRST- when the state engine gets reset...
*/
- if (info->chip_type >= HPT374 || info->settings[clock] == NULL) {
+ if (chip_type >= HPT374 || info->settings[clock] == NULL) {
u16 f_low, delta = pci_clk < 50 ? 2 : 4;
int adjust;
* Select 66 MHz DPLL clock only if UltraATA/133 mode is
* supported/enabled, use 50 MHz DPLL clock otherwise...
*/
- if (info->max_ultra == 6) {
+ if (info->udma_mask == ATA_UDMA6) {
dpll_clk = 66;
clock = ATA_CLOCK_66MHZ;
} else if (dpll_clk) { /* HPT36x chips don't have DPLL */
/* Point to this chip's own instance of the hpt_info structure. */
pci_set_drvdata(dev, info);
- if (info->chip_type >= HPT370) {
+ if (chip_type >= HPT370) {
u8 mcr1, mcr4;
/*
* the MISC. register to stretch the UltraDMA Tss timing.
* NOTE: This register is only writeable via I/O space.
*/
- if (info->chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
+ if (chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c);
static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = pci_get_drvdata(dev);
- int serialize = HPT_SERIALIZE_IO;
- u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
- u8 chip_type = info->chip_type;
- u8 new_mcr, old_mcr = 0;
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
+ int serialize = HPT_SERIALIZE_IO;
+ u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
+ u8 chip_type = info->chip_type;
+ u8 new_mcr, old_mcr = 0;
/* Cache the channel's MISC. control registers' offset */
- hwif->select_data = hwif->channel ? 0x54 : 0x50;
+ hwif->select_data = hwif->channel ? 0x54 : 0x50;
- hwif->tuneproc = &hpt3xx_tune_drive;
- hwif->speedproc = &hpt3xx_tune_chipset;
- hwif->quirkproc = &hpt3xx_quirkproc;
- hwif->intrproc = &hpt3xx_intrproc;
- hwif->maskproc = &hpt3xx_maskproc;
- hwif->busproc = &hpt3xx_busproc;
+ hwif->set_pio_mode = &hpt3xx_set_pio_mode;
+ hwif->set_dma_mode = &hpt3xx_set_mode;
+ hwif->quirkproc = &hpt3xx_quirkproc;
+ hwif->intrproc = &hpt3xx_intrproc;
+ hwif->maskproc = &hpt3xx_maskproc;
+ hwif->busproc = &hpt3xx_busproc;
- if (chip_type <= HPT370A)
- hwif->udma_filter = &hpt3xx_udma_filter;
+ hwif->udma_filter = &hpt3xx_udma_filter;
+ hwif->mdma_filter = &hpt3xx_mdma_filter;
/*
* HPT3xxN chips have some complications:
if (new_mcr != old_mcr)
pci_write_config_byte(dev, hwif->select_data + 1, new_mcr);
- if (!hwif->dma_base) {
- hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+ if (hwif->dma_base == 0)
return;
- }
-
- hwif->ultra_mask = hwif->cds->udma_mask;
- hwif->mwdma_mask = 0x07;
/*
* The HPT37x uses the CBLID pins as outputs for MA15/MA16
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = (scr1 & ata66) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
- hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
-
if (chip_type >= HPT374) {
hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
hwif->ide_dma_end = &hpt374_ide_dma_end;
hwif->dma_timeout = &hpt370_dma_timeout;
} else
hwif->dma_lost_irq = &hpt366_dma_lost_irq;
-
- if (!noautodma)
- hwif->autodma = 1;
- hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
u8 dma_new = 0, dma_old = 0;
unsigned long flags;
- dma_old = hwif->INB(dmabase + 2);
+ dma_old = inb(dmabase + 2);
local_irq_save(flags);
if (masterdma & 0x30) dma_new |= 0x20;
if ( slavedma & 0x30) dma_new |= 0x40;
if (dma_new != dma_old)
- hwif->OUTB(dma_new, dmabase + 2);
+ outb(dma_new, dmabase + 2);
local_irq_restore(flags);
ide_setup_dma(hwif, dmabase, 8);
}
-static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
+static void __devinit hpt374_init(struct pci_dev *dev, struct pci_dev *dev2)
{
- struct pci_dev *dev2;
-
- if (PCI_FUNC(dev->devfn) & 1)
- return -ENODEV;
-
- pci_set_drvdata(dev, &hpt374);
-
- if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
- int ret;
-
- pci_set_drvdata(dev2, &hpt374);
-
- if (dev2->irq != dev->irq) {
- /* FIXME: we need a core pci_set_interrupt() */
- dev2->irq = dev->irq;
- printk(KERN_WARNING "%s: PCI config space interrupt "
- "fixed.\n", d->name);
- }
- ret = ide_setup_pci_devices(dev, dev2, d);
- if (ret < 0)
- pci_dev_put(dev2);
- return ret;
+ if (dev2->irq != dev->irq) {
+ /* FIXME: we need a core pci_set_interrupt() */
+ dev2->irq = dev->irq;
+ printk(KERN_INFO "HPT374: PCI config space interrupt fixed\n");
}
- return ide_setup_pci_device(dev, d);
}
-static int __devinit init_setup_hpt372n(struct pci_dev *dev, ide_pci_device_t *d)
+static void __devinit hpt371_init(struct pci_dev *dev)
{
- pci_set_drvdata(dev, &hpt372n);
-
- return ide_setup_pci_device(dev, d);
-}
-
-static int __devinit init_setup_hpt371(struct pci_dev *dev, ide_pci_device_t *d)
-{
- struct hpt_info *info;
u8 mcr1 = 0;
- if (dev->revision > 1) {
- d->name = "HPT371N";
-
- info = &hpt371n;
- } else
- info = &hpt371;
-
/*
* HPT371 chips physically have only one channel, the secondary one,
* but the primary channel registers do exist! Go figure...
pci_read_config_byte(dev, 0x50, &mcr1);
if (mcr1 & 0x04)
pci_write_config_byte(dev, 0x50, mcr1 & ~0x04);
-
- pci_set_drvdata(dev, info);
-
- return ide_setup_pci_device(dev, d);
}
-static int __devinit init_setup_hpt372a(struct pci_dev *dev, ide_pci_device_t *d)
+static int __devinit hpt36x_init(struct pci_dev *dev, struct pci_dev *dev2)
{
- struct hpt_info *info;
+ u8 mcr1 = 0, pin1 = 0, pin2 = 0;
- if (dev->revision > 1) {
- d->name = "HPT372N";
-
- info = &hpt372n;
- } else
- info = &hpt372a;
- pci_set_drvdata(dev, info);
-
- return ide_setup_pci_device(dev, d);
-}
-
-static int __devinit init_setup_hpt302(struct pci_dev *dev, ide_pci_device_t *d)
-{
- struct hpt_info *info;
+ /*
+ * Now we'll have to force both channels enabled if
+ * at least one of them has been enabled by BIOS...
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x30)
+ pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
- if (dev->revision > 1) {
- d->name = "HPT302N";
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
+ pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
- info = &hpt302n;
- } else
- info = &hpt302;
- pci_set_drvdata(dev, info);
+ if (pin1 != pin2 && dev->irq == dev2->irq) {
+ printk(KERN_INFO "HPT36x: onboard version of chipset, "
+ "pin1=%d pin2=%d\n", pin1, pin2);
+ return 1;
+ }
- return ide_setup_pci_device(dev, d);
+ return 0;
}
-static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d)
-{
- struct pci_dev *dev2;
- u8 rev = dev->revision;
- static char *chipset_names[] = { "HPT366", "HPT366", "HPT368",
- "HPT370", "HPT370A", "HPT372",
- "HPT372N" };
- static struct hpt_info *info[] = { &hpt36x, &hpt36x, &hpt36x,
- &hpt370, &hpt370a, &hpt372,
- &hpt372n };
-
- if (PCI_FUNC(dev->devfn) & 1)
- return -ENODEV;
-
- switch (rev) {
- case 0:
- case 1:
- case 2:
+static const struct ide_port_info hpt366_chipsets[] __devinitdata = {
+ { /* 0 */
+ .name = "HPT36x",
+ .init_chipset = init_chipset_hpt366,
+ .init_hwif = init_hwif_hpt366,
+ .init_dma = init_dma_hpt366,
/*
* HPT36x chips have one channel per function and have
* both channel enable bits located differently and visible
* to both functions -- really stupid design decision... :-(
* Bit 4 is for the primary channel, bit 5 for the secondary.
*/
- d->host_flags |= IDE_HFLAG_SINGLE;
- d->enablebits[0].mask = d->enablebits[0].val = 0x10;
-
- d->udma_mask = HPT366_ALLOW_ATA66_3 ?
- (HPT366_ALLOW_ATA66_4 ? 0x1f : 0x0f) : 0x07;
- break;
- case 3:
- case 4:
- d->udma_mask = HPT370_ALLOW_ATA100_5 ? 0x3f : 0x1f;
- break;
- default:
- rev = 6;
- /* fall thru */
- case 5:
- case 6:
- d->udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f;
- break;
- }
-
- d->name = chipset_names[rev];
-
- pci_set_drvdata(dev, info[rev]);
-
- if (rev > 2)
- goto init_single;
-
- if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
- u8 mcr1 = 0, pin1 = 0, pin2 = 0;
- int ret;
-
- pci_set_drvdata(dev2, info[rev]);
-
- /*
- * Now we'll have to force both channels enabled if
- * at least one of them has been enabled by BIOS...
- */
- pci_read_config_byte(dev, 0x50, &mcr1);
- if (mcr1 & 0x30)
- pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
-
- pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
- pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
- if (pin1 != pin2 && dev->irq == dev2->irq) {
- d->bootable = ON_BOARD;
- printk("%s: onboard version of chipset, pin1=%d pin2=%d\n",
- d->name, pin1, pin2);
- }
- ret = ide_setup_pci_devices(dev, dev2, d);
- if (ret < 0)
- pci_dev_put(dev2);
- return ret;
- }
-init_single:
- return ide_setup_pci_device(dev, d);
-}
-
-static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "HPT366",
- .init_setup = init_setup_hpt366,
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .bootable = OFF_BOARD,
+ .enablebits = {{0x50,0x10,0x10}, {0x54,0x04,0x04}},
.extra = 240,
+ .host_flags = IDE_HFLAG_SINGLE |
+ IDE_HFLAG_NO_ATAPI_DMA |
+ IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
},{ /* 1 */
.name = "HPT372A",
- .init_setup = init_setup_hpt372a,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
- .bootable = OFF_BOARD,
.extra = 240,
+ .host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
},{ /* 2 */
.name = "HPT302",
- .init_setup = init_setup_hpt302,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT302_ALLOW_ATA133_6 ? 0x7f : 0x3f,
- .bootable = OFF_BOARD,
.extra = 240,
+ .host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
},{ /* 3 */
.name = "HPT371",
- .init_setup = init_setup_hpt371,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT371_ALLOW_ATA133_6 ? 0x7f : 0x3f,
- .bootable = OFF_BOARD,
.extra = 240,
+ .host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
},{ /* 4 */
.name = "HPT374",
- .init_setup = init_setup_hpt374,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = 0x3f,
- .bootable = OFF_BOARD,
+ .udma_mask = ATA_UDMA5,
.extra = 240,
+ .host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
},{ /* 5 */
.name = "HPT372N",
- .init_setup = init_setup_hpt372n,
.init_chipset = init_chipset_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
- .autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
- .bootable = OFF_BOARD,
.extra = 240,
+ .host_flags = IDE_HFLAG_NO_ATAPI_DMA | IDE_HFLAG_OFF_BOARD,
.pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
}
};
*
* Called when the PCI registration layer (or the IDE initialization)
* finds a device matching our IDE device tables.
- *
- * NOTE: since we'll have to modify some fields of the ide_pci_device_t
- * structure depending on the chip's revision, we'd better pass a local
- * copy down the call chain...
*/
static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_pci_device_t d = hpt366_chipsets[id->driver_data];
+ struct hpt_info *info = NULL;
+ struct pci_dev *dev2 = NULL;
+ struct ide_port_info d;
+ u8 idx = id->driver_data;
+ u8 rev = dev->revision;
+
+ if ((idx == 0 || idx == 4) && (PCI_FUNC(dev->devfn) & 1))
+ return -ENODEV;
+
+ switch (idx) {
+ case 0:
+ if (rev < 3)
+ info = &hpt36x;
+ else {
+ static struct hpt_info *hpt37x_info[] =
+ { &hpt370, &hpt370a, &hpt372, &hpt372n };
+
+ info = hpt37x_info[min_t(u8, rev, 6) - 3];
+ idx++;
+ }
+ break;
+ case 1:
+ info = (rev > 1) ? &hpt372n : &hpt372a;
+ break;
+ case 2:
+ info = (rev > 1) ? &hpt302n : &hpt302;
+ break;
+ case 3:
+ hpt371_init(dev);
+ info = (rev > 1) ? &hpt371n : &hpt371;
+ break;
+ case 4:
+ info = &hpt374;
+ break;
+ case 5:
+ info = &hpt372n;
+ break;
+ }
+
+ d = hpt366_chipsets[idx];
+
+ d.name = info->chip_name;
+ d.udma_mask = info->udma_mask;
+
+ pci_set_drvdata(dev, info);
+
+ if (info == &hpt36x || info == &hpt374)
+ dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
+
+ if (dev2) {
+ int ret;
+
+ pci_set_drvdata(dev2, info);
+
+ if (info == &hpt374)
+ hpt374_init(dev, dev2);
+ else {
+ if (hpt36x_init(dev, dev2))
+ d.host_flags |= IDE_HFLAG_BOOTABLE;
+ }
+
+ ret = ide_setup_pci_devices(dev, dev2, &d);
+ if (ret < 0)
+ pci_dev_put(dev2);
+ return ret;
+ }
- return d.init_setup(dev, &d);
+ return ide_setup_pci_device(dev, &d);
}
-static struct pci_device_id hpt366_pci_tbl[] = {
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
- { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
+static const struct pci_device_id hpt366_pci_tbl[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), 0 },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), 1 },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), 2 },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), 3 },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), 4 },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), 5 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl);
projects / linux-2.6-omap-h63xx.git / blobdiff