/*
- * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
+ * linux/drivers/ide/pci/hpt366.c Version 1.06 Jun 27, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
*
* Thanks to HighPoint Technologies for their assistance, and hardware.
* Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
* development and support.
*
*
- * Highpoint have their own driver (source except for the raid part)
- * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz
- * This may be useful to anyone wanting to work on the mainstream hpt IDE.
+ * HighPoint has its own drivers (open source except for the RAID part)
+ * available from http://www.highpoint-tech.com/BIOS%20+%20Driver/.
+ * This may be useful to anyone wanting to work on this driver, however do not
+ * trust them too much since the code tends to become less and less meaningful
+ * as the time passes... :-/
*
* Note that final HPT370 support was done by force extraction of GPL.
*
* keeping me sane.
* Alan Cox <alan@redhat.com>
*
+ * - fix the clock turnaround code: it was writing to the wrong ports when
+ * called for the secondary channel, caching the current clock mode per-
+ * channel caused the cached register value to get out of sync with the
+ * actual one, the channels weren't serialized, the turnaround shouldn't
+ * be done on 66 MHz PCI bus
+ * - disable UltraATA/100 for HPT370 by default as the 33 MHz clock being used
+ * does not allow for this speed anyway
+ * - avoid touching disabled channels (e.g. HPT371/N are single channel chips,
+ * their primary channel is kind of virtual, it isn't tied to any pins)
+ * - fix/remove bad/unused timing tables and use one set of tables for the whole
+ * HPT37x chip family; save space by introducing the separate transfer mode
+ * table in which the mode lookup is done
+ * - use f_CNT value saved by the HighPoint BIOS as reading it directly gives
+ * the wrong PCI frequency since DPLL has already been calibrated by BIOS
+ * - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
+ * and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
+ * - pass to init_chipset() handlers a copy of the IDE PCI device structure as
+ * they tamper with its fields
+ * - pass to the init_setup handlers a copy of the ide_pci_device_t structure
+ * since they may tamper with its fields
+ * - prefix the driver startup messages with the real chip name
+ * - claim the extra 240 bytes of I/O space for all chips
+ * - optimize the rate masking/filtering and the drive list lookup code
+ * - use pci_get_slot() to get to the function 1 of HPT36x/374
+ * - cache offset of the channel's misc. control registers (MCRs) being used
+ * throughout the driver
+ * - only touch the relevant MCR when detecting the cable type on HPT374's
+ * function 1
+ * - rename all the register related variables consistently
+ * - move all the interrupt twiddling code from the speedproc handlers into
+ * init_hwif_hpt366(), also grouping all the DMA related code together there
+ * - merge two HPT37x speedproc handlers, fix the PIO timing register mask and
+ * separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
+ * when setting an UltraDMA mode
+ * - fix hpt3xx_tune_drive() to set the PIO mode requested, not always select
+ * the best possible one
+ * - clean up DMA timeout handling for HPT370
+ * - switch to using the enumeration type to differ between the numerous chip
+ * variants, matching PCI device/revision ID with the chip type early, at the
+ * init_setup stage
+ * - extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
+ * stop duplicating it for each channel by storing the pointer in the pci_dev
+ * structure: first, at the init_setup stage, point it to a static "template"
+ * with only the chip type and its specific base DPLL frequency, the highest
+ * supported DMA mode, and the chip settings table pointer filled, then, at
+ * the init_chipset stage, allocate per-chip instance and fill it with the
+ * rest of the necessary information
+ * - get rid of the constant thresholds in the HPT37x PCI clock detection code,
+ * switch to calculating PCI clock frequency based on the chip's base DPLL
+ * frequency
+ * - switch to using the DPLL clock and enable UltraATA/133 mode by default on
+ * anything newer than HPT370/A (except HPT374 that is not capable of this
+ * mode according to the manual)
+ * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
+ * also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
+ * unify HPT36x/37x timing setup code and the speedproc handlers by joining
+ * the register setting lists into the table indexed by the clock selected
+ * Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com>
*/
-
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
/* various tuning parameters */
#define HPT_RESET_STATE_ENGINE
-#undef HPT_DELAY_INTERRUPT
-#undef HPT_SERIALIZE_IO
+#undef HPT_DELAY_INTERRUPT
+#define HPT_SERIALIZE_IO 0
static const char *quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
"IC35L040AVER07-0",
"IC35L060AVER07-0",
"WDC AC310200R",
+ "MAXTOR STM3320620A",
NULL
};
NULL
};
-struct chipset_bus_clock_list_entry {
- u8 xfer_speed;
- unsigned int chipset_settings;
+static u8 xfer_speeds[] = {
+ XFER_UDMA_6,
+ XFER_UDMA_5,
+ XFER_UDMA_4,
+ XFER_UDMA_3,
+ XFER_UDMA_2,
+ XFER_UDMA_1,
+ XFER_UDMA_0,
+
+ XFER_MW_DMA_2,
+ XFER_MW_DMA_1,
+ XFER_MW_DMA_0,
+
+ XFER_PIO_4,
+ XFER_PIO_3,
+ XFER_PIO_2,
+ XFER_PIO_1,
+ XFER_PIO_0
};
-/* key for bus clock timings
- * bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
- * register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
- * register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
- * register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+/* Key for bus clock timings
+ * 36x 37x
+ * bits bits
+ * 0:3 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:7 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 8:11 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
+ * register access.
+ * 12:15 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
+ * register access.
+ * 16:18 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * - 21 CLK frequency: 0=ATA clock, 1=dual ATA clock.
+ * 19:21 22:24 pre_high_time. Time to initialize the 1st cycle for PIO and
+ * MW DMA xfer.
+ * 22:24 25:27 cmd_pre_high_time. Time to initialize the 1st PIO cycle for
+ * task file register access.
+ * 28 28 UDMA enable.
+ * 29 29 DMA enable.
+ * 30 30 PIO MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 31 FIFO enable.
*/
-static struct chipset_bus_clock_list_entry forty_base_hpt366[] = {
- { XFER_UDMA_4, 0x900fd943 },
- { XFER_UDMA_3, 0x900ad943 },
- { XFER_UDMA_2, 0x900bd943 },
- { XFER_UDMA_1, 0x9008d943 },
- { XFER_UDMA_0, 0x9008d943 },
-
- { XFER_MW_DMA_2, 0xa008d943 },
- { XFER_MW_DMA_1, 0xa010d955 },
- { XFER_MW_DMA_0, 0xa010d9fc },
-
- { XFER_PIO_4, 0xc008d963 },
- { XFER_PIO_3, 0xc010d974 },
- { XFER_PIO_2, 0xc010d997 },
- { XFER_PIO_1, 0xc010d9c7 },
- { XFER_PIO_0, 0xc018d9d9 },
- { 0, 0x0120d9d9 }
+
+static u32 forty_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x900fd943,
+ /* XFER_UDMA_5 */ 0x900fd943,
+ /* XFER_UDMA_4 */ 0x900fd943,
+ /* XFER_UDMA_3 */ 0x900ad943,
+ /* XFER_UDMA_2 */ 0x900bd943,
+ /* XFER_UDMA_1 */ 0x9008d943,
+ /* XFER_UDMA_0 */ 0x9008d943,
+
+ /* XFER_MW_DMA_2 */ 0xa008d943,
+ /* XFER_MW_DMA_1 */ 0xa010d955,
+ /* XFER_MW_DMA_0 */ 0xa010d9fc,
+
+ /* XFER_PIO_4 */ 0xc008d963,
+ /* XFER_PIO_3 */ 0xc010d974,
+ /* XFER_PIO_2 */ 0xc010d997,
+ /* XFER_PIO_1 */ 0xc010d9c7,
+ /* XFER_PIO_0 */ 0xc018d9d9
};
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = {
- { XFER_UDMA_4, 0x90c9a731 },
- { XFER_UDMA_3, 0x90cfa731 },
- { XFER_UDMA_2, 0x90caa731 },
- { XFER_UDMA_1, 0x90cba731 },
- { XFER_UDMA_0, 0x90c8a731 },
-
- { XFER_MW_DMA_2, 0xa0c8a731 },
- { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
- { XFER_MW_DMA_0, 0xa0c8a797 },
-
- { XFER_PIO_4, 0xc0c8a731 },
- { XFER_PIO_3, 0xc0c8a742 },
- { XFER_PIO_2, 0xc0d0a753 },
- { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
- { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
- { 0, 0x0120a7a7 }
+static u32 thirty_three_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x90c9a731,
+ /* XFER_UDMA_5 */ 0x90c9a731,
+ /* XFER_UDMA_4 */ 0x90c9a731,
+ /* XFER_UDMA_3 */ 0x90cfa731,
+ /* XFER_UDMA_2 */ 0x90caa731,
+ /* XFER_UDMA_1 */ 0x90cba731,
+ /* XFER_UDMA_0 */ 0x90c8a731,
+
+ /* XFER_MW_DMA_2 */ 0xa0c8a731,
+ /* XFER_MW_DMA_1 */ 0xa0c8a732, /* 0xa0c8a733 */
+ /* XFER_MW_DMA_0 */ 0xa0c8a797,
+
+ /* XFER_PIO_4 */ 0xc0c8a731,
+ /* XFER_PIO_3 */ 0xc0c8a742,
+ /* XFER_PIO_2 */ 0xc0d0a753,
+ /* XFER_PIO_1 */ 0xc0d0a7a3, /* 0xc0d0a793 */
+ /* XFER_PIO_0 */ 0xc0d0a7aa /* 0xc0d0a7a7 */
};
-static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = {
- { XFER_UDMA_4, 0x90c98521 },
- { XFER_UDMA_3, 0x90cf8521 },
- { XFER_UDMA_2, 0x90cf8521 },
- { XFER_UDMA_1, 0x90cb8521 },
- { XFER_UDMA_0, 0x90cb8521 },
-
- { XFER_MW_DMA_2, 0xa0ca8521 },
- { XFER_MW_DMA_1, 0xa0ca8532 },
- { XFER_MW_DMA_0, 0xa0ca8575 },
-
- { XFER_PIO_4, 0xc0ca8521 },
- { XFER_PIO_3, 0xc0ca8532 },
- { XFER_PIO_2, 0xc0ca8542 },
- { XFER_PIO_1, 0xc0d08572 },
- { XFER_PIO_0, 0xc0d08585 },
- { 0, 0x01208585 }
+static u32 twenty_five_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x90c98521,
+ /* XFER_UDMA_5 */ 0x90c98521,
+ /* XFER_UDMA_4 */ 0x90c98521,
+ /* XFER_UDMA_3 */ 0x90cf8521,
+ /* XFER_UDMA_2 */ 0x90cf8521,
+ /* XFER_UDMA_1 */ 0x90cb8521,
+ /* XFER_UDMA_0 */ 0x90cb8521,
+
+ /* XFER_MW_DMA_2 */ 0xa0ca8521,
+ /* XFER_MW_DMA_1 */ 0xa0ca8532,
+ /* XFER_MW_DMA_0 */ 0xa0ca8575,
+
+ /* XFER_PIO_4 */ 0xc0ca8521,
+ /* XFER_PIO_3 */ 0xc0ca8532,
+ /* XFER_PIO_2 */ 0xc0ca8542,
+ /* XFER_PIO_1 */ 0xc0d08572,
+ /* XFER_PIO_0 */ 0xc0d08585
};
-/* from highpoint documentation. these are old values */
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = {
-/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */
- { XFER_UDMA_5, 0x16454e31 },
- { XFER_UDMA_4, 0x16454e31 },
- { XFER_UDMA_3, 0x166d4e31 },
- { XFER_UDMA_2, 0x16494e31 },
- { XFER_UDMA_1, 0x164d4e31 },
- { XFER_UDMA_0, 0x16514e31 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
+static u32 thirty_three_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x12446231, /* 0x12646231 ?? */
+ /* XFER_UDMA_5 */ 0x12446231,
+ /* XFER_UDMA_4 */ 0x12446231,
+ /* XFER_UDMA_3 */ 0x126c6231,
+ /* XFER_UDMA_2 */ 0x12486231,
+ /* XFER_UDMA_1 */ 0x124c6233,
+ /* XFER_UDMA_0 */ 0x12506297,
+
+ /* XFER_MW_DMA_2 */ 0x22406c31,
+ /* XFER_MW_DMA_1 */ 0x22406c33,
+ /* XFER_MW_DMA_0 */ 0x22406c97,
+
+ /* XFER_PIO_4 */ 0x06414e31,
+ /* XFER_PIO_3 */ 0x06414e42,
+ /* XFER_PIO_2 */ 0x06414e53,
+ /* XFER_PIO_1 */ 0x06814e93,
+ /* XFER_PIO_0 */ 0x06814ea7
};
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt370[] = {
- { XFER_UDMA_5, 0x14846231 },
- { XFER_UDMA_4, 0x14886231 },
- { XFER_UDMA_3, 0x148c6231 },
- { XFER_UDMA_2, 0x148c6231 },
- { XFER_UDMA_1, 0x14906231 },
- { XFER_UDMA_0, 0x14986231 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
+static u32 fifty_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x12848242,
+ /* XFER_UDMA_5 */ 0x12848242,
+ /* XFER_UDMA_4 */ 0x12ac8242,
+ /* XFER_UDMA_3 */ 0x128c8242,
+ /* XFER_UDMA_2 */ 0x120c8242,
+ /* XFER_UDMA_1 */ 0x12148254,
+ /* XFER_UDMA_0 */ 0x121882ea,
+
+ /* XFER_MW_DMA_2 */ 0x22808242,
+ /* XFER_MW_DMA_1 */ 0x22808254,
+ /* XFER_MW_DMA_0 */ 0x228082ea,
+
+ /* XFER_PIO_4 */ 0x0a81f442,
+ /* XFER_PIO_3 */ 0x0a81f443,
+ /* XFER_PIO_2 */ 0x0a81f454,
+ /* XFER_PIO_1 */ 0x0ac1f465,
+ /* XFER_PIO_0 */ 0x0ac1f48a
};
-/* these are the current (4 sep 2001) timings from highpoint */
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = {
- { XFER_UDMA_5, 0x12446231 },
- { XFER_UDMA_4, 0x12446231 },
- { XFER_UDMA_3, 0x126c6231 },
- { XFER_UDMA_2, 0x12486231 },
- { XFER_UDMA_1, 0x124c6233 },
- { XFER_UDMA_0, 0x12506297 },
-
- { XFER_MW_DMA_2, 0x22406c31 },
- { XFER_MW_DMA_1, 0x22406c33 },
- { XFER_MW_DMA_0, 0x22406c97 },
-
- { XFER_PIO_4, 0x06414e31 },
- { XFER_PIO_3, 0x06414e42 },
- { XFER_PIO_2, 0x06414e53 },
- { XFER_PIO_1, 0x06814e93 },
- { XFER_PIO_0, 0x06814ea7 },
- { 0, 0x06814ea7 }
+static u32 sixty_six_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x1c869c62,
+ /* XFER_UDMA_5 */ 0x1cae9c62, /* 0x1c8a9c62 */
+ /* XFER_UDMA_4 */ 0x1c8a9c62,
+ /* XFER_UDMA_3 */ 0x1c8e9c62,
+ /* XFER_UDMA_2 */ 0x1c929c62,
+ /* XFER_UDMA_1 */ 0x1c9a9c62,
+ /* XFER_UDMA_0 */ 0x1c829c62,
+
+ /* XFER_MW_DMA_2 */ 0x2c829c62,
+ /* XFER_MW_DMA_1 */ 0x2c829c66,
+ /* XFER_MW_DMA_0 */ 0x2c829d2e,
+
+ /* XFER_PIO_4 */ 0x0c829c62,
+ /* XFER_PIO_3 */ 0x0c829c84,
+ /* XFER_PIO_2 */ 0x0c829ca6,
+ /* XFER_PIO_1 */ 0x0d029d26,
+ /* XFER_PIO_0 */ 0x0d029d5e
};
-/* 2x 33MHz timings */
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt370a[] = {
- { XFER_UDMA_5, 0x1488e673 },
- { XFER_UDMA_4, 0x1488e673 },
- { XFER_UDMA_3, 0x1498e673 },
- { XFER_UDMA_2, 0x1490e673 },
- { XFER_UDMA_1, 0x1498e677 },
- { XFER_UDMA_0, 0x14a0e73f },
-
- { XFER_MW_DMA_2, 0x2480fa73 },
- { XFER_MW_DMA_1, 0x2480fa77 },
- { XFER_MW_DMA_0, 0x2480fb3f },
-
- { XFER_PIO_4, 0x0c82be73 },
- { XFER_PIO_3, 0x0c82be95 },
- { XFER_PIO_2, 0x0c82beb7 },
- { XFER_PIO_1, 0x0d02bf37 },
- { XFER_PIO_0, 0x0d02bf5f },
- { 0, 0x0d02bf5f }
+#define HPT366_DEBUG_DRIVE_INFO 0
+#define HPT371_ALLOW_ATA133_6 1
+#define HPT302_ALLOW_ATA133_6 1
+#define HPT372_ALLOW_ATA133_6 1
+#define HPT370_ALLOW_ATA100_5 0
+#define HPT366_ALLOW_ATA66_4 1
+#define HPT366_ALLOW_ATA66_3 1
+#define HPT366_MAX_DEVS 8
+
+/* Supported ATA clock frequencies */
+enum ata_clock {
+ ATA_CLOCK_25MHZ,
+ ATA_CLOCK_33MHZ,
+ ATA_CLOCK_40MHZ,
+ ATA_CLOCK_50MHZ,
+ ATA_CLOCK_66MHZ,
+ NUM_ATA_CLOCKS
};
-static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0ac1f48a }
+/*
+ * Hold all the HighPoint chip information in one place.
+ */
+
+struct hpt_info {
+ u8 chip_type; /* Chip type */
+ u8 max_mode; /* Speeds allowed */
+ u8 dpll_clk; /* DPLL clock in MHz */
+ u8 pci_clk; /* PCI clock in MHz */
+ u32 **settings; /* Chipset settings table */
};
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = {
- { XFER_UDMA_6, 0x1c81dc62 },
- { XFER_UDMA_5, 0x1c6ddc62 },
- { XFER_UDMA_4, 0x1c8ddc62 },
- { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */
- { XFER_UDMA_2, 0x1c91dc62 },
- { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */
- { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */
-
- { XFER_MW_DMA_2, 0x2c829262 },
- { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */
- { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d5e }
+/* Supported HighPoint chips */
+enum {
+ HPT36x,
+ HPT370,
+ HPT370A,
+ HPT374,
+ HPT372,
+ HPT372A,
+ HPT302,
+ HPT371,
+ HPT372N,
+ HPT302N,
+ HPT371N
};
-static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0a81f443 }
+static u32 *hpt36x_settings[NUM_ATA_CLOCKS] = {
+ twenty_five_base_hpt36x,
+ thirty_three_base_hpt36x,
+ forty_base_hpt36x,
+ NULL,
+ NULL
};
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = {
- { XFER_UDMA_6, 0x1c869c62 },
- { XFER_UDMA_5, 0x1cae9c62 },
- { XFER_UDMA_4, 0x1c8a9c62 },
- { XFER_UDMA_3, 0x1c8e9c62 },
- { XFER_UDMA_2, 0x1c929c62 },
- { XFER_UDMA_1, 0x1c9a9c62 },
- { XFER_UDMA_0, 0x1c829c62 },
-
- { XFER_MW_DMA_2, 0x2c829c62 },
- { XFER_MW_DMA_1, 0x2c829c66 },
- { XFER_MW_DMA_0, 0x2c829d2e },
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d26 }
+static u32 *hpt37x_settings[NUM_ATA_CLOCKS] = {
+ NULL,
+ thirty_three_base_hpt37x,
+ NULL,
+ fifty_base_hpt37x,
+ sixty_six_base_hpt37x
};
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt374[] = {
- { XFER_UDMA_6, 0x12808242 },
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x06814e93 }
+static struct hpt_info hpt36x __devinitdata = {
+ .chip_type = HPT36x,
+ .max_mode = (HPT366_ALLOW_ATA66_4 || HPT366_ALLOW_ATA66_3) ? 2 : 1,
+ .dpll_clk = 0, /* no DPLL */
+ .settings = hpt36x_settings
};
-/* FIXME: 50MHz timings for HPT374 */
-
-#if 0
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = {
- { XFER_UDMA_6, 0x12406231 }, /* checkme */
- { XFER_UDMA_5, 0x12446231 }, /* 0x14846231 */
- { XFER_UDMA_4, 0x16814ea7 }, /* 0x14886231 */
- { XFER_UDMA_3, 0x16814ea7 }, /* 0x148c6231 */
- { XFER_UDMA_2, 0x16814ea7 }, /* 0x148c6231 */
- { XFER_UDMA_1, 0x16814ea7 }, /* 0x14906231 */
- { XFER_UDMA_0, 0x16814ea7 }, /* 0x14986231 */
- { XFER_MW_DMA_2, 0x16814ea7 }, /* 0x26514e21 */
- { XFER_MW_DMA_1, 0x16814ea7 }, /* 0x26514e97 */
- { XFER_MW_DMA_0, 0x16814ea7 }, /* 0x26514e97 */
- { XFER_PIO_4, 0x06814ea7 }, /* 0x06514e21 */
- { XFER_PIO_3, 0x06814ea7 }, /* 0x06514e22 */
- { XFER_PIO_2, 0x06814ea7 }, /* 0x06514e33 */
- { XFER_PIO_1, 0x06814ea7 }, /* 0x06914e43 */
- { XFER_PIO_0, 0x06814ea7 }, /* 0x06914e57 */
- { 0, 0x06814ea7 }
+static struct hpt_info hpt370 __devinitdata = {
+ .chip_type = HPT370,
+ .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2,
+ .dpll_clk = 48,
+ .settings = hpt37x_settings
};
-#endif
-#define HPT366_DEBUG_DRIVE_INFO 0
-#define HPT374_ALLOW_ATA133_6 0
-#define HPT371_ALLOW_ATA133_6 0
-#define HPT302_ALLOW_ATA133_6 0
-#define HPT372_ALLOW_ATA133_6 1
-#define HPT370_ALLOW_ATA100_5 1
-#define HPT366_ALLOW_ATA66_4 1
-#define HPT366_ALLOW_ATA66_3 1
-#define HPT366_MAX_DEVS 8
+static struct hpt_info hpt370a __devinitdata = {
+ .chip_type = HPT370A,
+ .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2,
+ .dpll_clk = 48,
+ .settings = hpt37x_settings
+};
-#define F_LOW_PCI_33 0x23
-#define F_LOW_PCI_40 0x29
-#define F_LOW_PCI_50 0x2d
-#define F_LOW_PCI_66 0x42
+static struct hpt_info hpt374 __devinitdata = {
+ .chip_type = HPT374,
+ .max_mode = 3,
+ .dpll_clk = 48,
+ .settings = hpt37x_settings
+};
-/*
- * Hold all the highpoint quirks and revision information in one
- * place.
- */
+static struct hpt_info hpt372 __devinitdata = {
+ .chip_type = HPT372,
+ .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 55,
+ .settings = hpt37x_settings
+};
-struct hpt_info
-{
- u8 max_mode; /* Speeds allowed */
- int revision; /* Chipset revision */
- int flags; /* Chipset properties */
-#define PLL_MODE 1
-#define IS_372N 2
- /* Speed table */
- struct chipset_bus_clock_list_entry *speed;
+static struct hpt_info hpt372a __devinitdata = {
+ .chip_type = HPT372A,
+ .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 66,
+ .settings = hpt37x_settings
};
-/*
- * This wants fixing so that we do everything not by classrev
- * (which breaks on the newest chips) but by creating an
- * enumeration of chip variants and using that
- */
+static struct hpt_info hpt302 __devinitdata = {
+ .chip_type = HPT302,
+ .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 66,
+ .settings = hpt37x_settings
+};
-static __devinit u32 hpt_revision (struct pci_dev *dev)
-{
- u32 class_rev;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
-
- switch(dev->device) {
- /* Remap new 372N onto 372 */
- case PCI_DEVICE_ID_TTI_HPT372N:
- class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
- case PCI_DEVICE_ID_TTI_HPT374:
- class_rev = PCI_DEVICE_ID_TTI_HPT374; break;
- case PCI_DEVICE_ID_TTI_HPT371:
- class_rev = PCI_DEVICE_ID_TTI_HPT371; break;
- case PCI_DEVICE_ID_TTI_HPT302:
- class_rev = PCI_DEVICE_ID_TTI_HPT302; break;
- case PCI_DEVICE_ID_TTI_HPT372:
- class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
- default:
- break;
- }
- return class_rev;
-}
+static struct hpt_info hpt371 __devinitdata = {
+ .chip_type = HPT371,
+ .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 66,
+ .settings = hpt37x_settings
+};
+
+static struct hpt_info hpt372n __devinitdata = {
+ .chip_type = HPT372N,
+ .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 77,
+ .settings = hpt37x_settings
+};
+
+static struct hpt_info hpt302n __devinitdata = {
+ .chip_type = HPT302N,
+ .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 77,
+ .settings = hpt37x_settings
+};
-static int check_in_drive_lists(ide_drive_t *drive, const char **list);
+static struct hpt_info hpt371n __devinitdata = {
+ .chip_type = HPT371N,
+ .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3,
+ .dpll_clk = 77,
+ .settings = hpt37x_settings
+};
-static u8 hpt3xx_ratemask (ide_drive_t *drive)
+static int check_in_drive_list(ide_drive_t *drive, const char **list)
{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 mode = 0;
-
- /* FIXME: TODO - move this to set info->mode once at boot */
-
- if (info->revision >= 8) { /* HPT374 */
- mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 7) { /* HPT371 */
- mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 6) { /* HPT302 */
- mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 5) { /* HPT372 */
- mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3;
- } else if (info->revision >= 4) { /* HPT370A */
- mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
- } else if (info->revision >= 3) { /* HPT370 */
- mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
- mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode;
- } else { /* HPT366 and HPT368 */
- mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2;
- }
- if (!eighty_ninty_three(drive) && mode)
- mode = min(mode, (u8)1);
- return mode;
+ struct hd_driveid *id = drive->id;
+
+ while (*list)
+ if (!strcmp(*list++,id->model))
+ return 1;
+ return 0;
}
/*
* Note for the future; the SATA hpt37x we must set
* either PIO or UDMA modes 0,4,5
*/
-
-static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 mode = hpt3xx_ratemask(drive);
- if (drive->media != ide_disk)
- return min(speed, (u8)XFER_PIO_4);
+static u8 hpt3xx_udma_filter(ide_drive_t *drive)
+{
+ struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
+ u8 chip_type = info->chip_type;
+ u8 mode = info->max_mode;
+ u8 mask;
- switch(mode) {
+ switch (mode) {
case 0x04:
- speed = min(speed, (u8)XFER_UDMA_6);
+ mask = 0x7f;
break;
case 0x03:
- speed = min(speed, (u8)XFER_UDMA_5);
- if (info->revision >= 5)
+ mask = 0x3f;
+ if (chip_type >= HPT374)
break;
- if (check_in_drive_lists(drive, bad_ata100_5))
- speed = min(speed, (u8)XFER_UDMA_4);
- break;
+ if (!check_in_drive_list(drive, bad_ata100_5))
+ goto check_bad_ata33;
+ /* fall thru */
case 0x02:
- speed = min(speed, (u8)XFER_UDMA_4);
- /*
- * CHECK ME, Does this need to be set to 5 ??
- */
- if (info->revision >= 3)
- break;
- if ((check_in_drive_lists(drive, bad_ata66_4)) ||
- (!(HPT366_ALLOW_ATA66_4)))
- speed = min(speed, (u8)XFER_UDMA_3);
- if ((check_in_drive_lists(drive, bad_ata66_3)) ||
- (!(HPT366_ALLOW_ATA66_3)))
- speed = min(speed, (u8)XFER_UDMA_2);
- break;
+ mask = 0x1f;
+
+ /*
+ * CHECK ME, Does this need to be changed to HPT374 ??
+ */
+ if (chip_type >= HPT370)
+ goto check_bad_ata33;
+ if (HPT366_ALLOW_ATA66_4 &&
+ !check_in_drive_list(drive, bad_ata66_4))
+ goto check_bad_ata33;
+
+ mask = 0x0f;
+ if (HPT366_ALLOW_ATA66_3 &&
+ !check_in_drive_list(drive, bad_ata66_3))
+ goto check_bad_ata33;
+ /* fall thru */
case 0x01:
- speed = min(speed, (u8)XFER_UDMA_2);
- /*
- * CHECK ME, Does this need to be set to 5 ??
- */
- if (info->revision >= 3)
+ mask = 0x07;
+
+ check_bad_ata33:
+ if (chip_type >= HPT370A)
break;
- if (check_in_drive_lists(drive, bad_ata33))
- speed = min(speed, (u8)XFER_MW_DMA_2);
- break;
+ if (!check_in_drive_list(drive, bad_ata33))
+ break;
+ /* fall thru */
case 0x00:
default:
- speed = min(speed, (u8)XFER_MW_DMA_2);
+ mask = 0x00;
break;
}
- return speed;
+ return mask;
}
-static int check_in_drive_lists (ide_drive_t *drive, const char **list)
+static u32 get_speed_setting(u8 speed, struct hpt_info *info)
{
- struct hd_driveid *id = drive->id;
+ int i;
- if (quirk_drives == list) {
- while (*list)
- if (strstr(id->model, *list++))
- return 1;
- } else {
- while (*list)
- if (!strcmp(*list++,id->model))
- return 1;
- }
- return 0;
-}
-
-static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
-{
- for ( ; chipset_table->xfer_speed ; chipset_table++)
- if (chipset_table->xfer_speed == speed)
- return chipset_table->chipset_settings;
- return chipset_table->chipset_settings;
+ /*
+ * Lookup the transfer mode table to get the index into
+ * the timing table.
+ *
+ * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used.
+ */
+ for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++)
+ if (xfer_speeds[i] == speed)
+ break;
+ /*
+ * NOTE: info->settings only points to the pointer
+ * to the list of the actual register values
+ */
+ return (*info->settings)[i];
}
static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 speed = hpt3xx_ratefilter(drive, xferspeed);
- u8 regtime = (drive->select.b.unit & 0x01) ? 0x44 : 0x40;
- u8 regfast = (hwif->channel) ? 0x55 : 0x51;
- u8 drive_fast = 0;
- u32 reg1 = 0, reg2 = 0;
+ ide_hwif_t *hwif = HWIF(drive);
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
+ u8 speed = ide_rate_filter(drive, xferspeed);
+ u8 itr_addr = drive->dn ? 0x44 : 0x40;
+ u32 old_itr = 0;
+ u32 itr_mask, new_itr;
+
+ /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
+ if (drive->media != ide_disk)
+ speed = min_t(u8, speed, XFER_PIO_4);
- /*
- * Disable the "fast interrupt" prediction.
- */
- pci_read_config_byte(dev, regfast, &drive_fast);
- if (drive_fast & 0x80)
- pci_write_config_byte(dev, regfast, drive_fast & ~0x80);
+ itr_mask = speed < XFER_MW_DMA_0 ? 0x30070000 :
+ (speed < XFER_UDMA_0 ? 0xc0070000 : 0xc03800ff);
- reg2 = pci_bus_clock_list(speed, info->speed);
+ new_itr = get_speed_setting(speed, info);
/*
- * Disable on-chip PIO FIFO/buffer
- * (to avoid problems handling I/O errors later)
+ * Disable on-chip PIO FIFO/buffer (and PIO MST mode as well)
+ * to avoid problems handling I/O errors later
*/
- pci_read_config_dword(dev, regtime, ®1);
- if (speed >= XFER_MW_DMA_0) {
- reg2 = (reg2 & ~0xc0000000) | (reg1 & 0xc0000000);
- } else {
- reg2 = (reg2 & ~0x30070000) | (reg1 & 0x30070000);
- }
- reg2 &= ~0x80000000;
+ pci_read_config_dword(dev, itr_addr, &old_itr);
+ new_itr = (new_itr & ~itr_mask) | (old_itr & itr_mask);
+ new_itr &= ~0xc0000000;
- pci_write_config_dword(dev, regtime, reg2);
+ pci_write_config_dword(dev, itr_addr, new_itr);
return ide_config_drive_speed(drive, speed);
}
-static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
+static int hpt37x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 speed = hpt3xx_ratefilter(drive, xferspeed);
- u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51;
- u8 drive_pci = 0x40 + (drive->dn * 4);
- u8 new_fast = 0, drive_fast = 0;
- u32 list_conf = 0, drive_conf = 0;
- u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
-
- /*
- * Disable the "fast interrupt" prediction.
- * don't holdoff on interrupts. (== 0x01 despite what the docs say)
- */
- pci_read_config_byte(dev, regfast, &drive_fast);
- new_fast = drive_fast;
- if (new_fast & 0x02)
- new_fast &= ~0x02;
+ ide_hwif_t *hwif = HWIF(drive);
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
+ u8 speed = ide_rate_filter(drive, xferspeed);
+ u8 itr_addr = 0x40 + (drive->dn * 4);
+ u32 old_itr = 0;
+ u32 itr_mask, new_itr;
+
+ /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
+ if (drive->media != ide_disk)
+ speed = min_t(u8, speed, XFER_PIO_4);
-#ifdef HPT_DELAY_INTERRUPT
- if (new_fast & 0x01)
- new_fast &= ~0x01;
-#else
- if ((new_fast & 0x01) == 0)
- new_fast |= 0x01;
-#endif
- if (new_fast != drive_fast)
- pci_write_config_byte(dev, regfast, new_fast);
+ itr_mask = speed < XFER_MW_DMA_0 ? 0x303c0000 :
+ (speed < XFER_UDMA_0 ? 0xc03c0000 : 0xc1c001ff);
- list_conf = pci_bus_clock_list(speed, info->speed);
+ new_itr = get_speed_setting(speed, info);
- pci_read_config_dword(dev, drive_pci, &drive_conf);
- list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
+ pci_read_config_dword(dev, itr_addr, &old_itr);
+ new_itr = (new_itr & ~itr_mask) | (old_itr & itr_mask);
if (speed < XFER_MW_DMA_0)
- list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
- pci_write_config_dword(dev, drive_pci, list_conf);
+ new_itr &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
+ pci_write_config_dword(dev, itr_addr, new_itr);
return ide_config_drive_speed(drive, speed);
}
-static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
+static int hpt3xx_tune_chipset(ide_drive_t *drive, u8 speed)
{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 speed = hpt3xx_ratefilter(drive, xferspeed);
- u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51;
- u8 drive_fast = 0, drive_pci = 0x40 + (drive->dn * 4);
- u32 list_conf = 0, drive_conf = 0;
- u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
-
- /*
- * Disable the "fast interrupt" prediction.
- * don't holdoff on interrupts. (== 0x01 despite what the docs say)
- */
- pci_read_config_byte(dev, regfast, &drive_fast);
- drive_fast &= ~0x07;
- pci_write_config_byte(dev, regfast, drive_fast);
-
- list_conf = pci_bus_clock_list(speed, info->speed);
- pci_read_config_dword(dev, drive_pci, &drive_conf);
- list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
- if (speed < XFER_MW_DMA_0)
- list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
- pci_write_config_dword(dev, drive_pci, list_conf);
-
- return ide_config_drive_speed(drive, speed);
-}
+ ide_hwif_t *hwif = HWIF(drive);
+ struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
-static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
-
- if (info->revision >= 8)
- return hpt372_tune_chipset(drive, speed); /* not a typo */
- else if (info->revision >= 5)
- return hpt372_tune_chipset(drive, speed);
- else if (info->revision >= 3)
- return hpt370_tune_chipset(drive, speed);
+ if (info->chip_type >= HPT370)
+ return hpt37x_tune_chipset(drive, speed);
else /* hpt368: hpt_minimum_revision(dev, 2) */
return hpt36x_tune_chipset(drive, speed);
}
-static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio)
+static void hpt3xx_tune_drive(ide_drive_t *drive, u8 pio)
{
- pio = ide_get_best_pio_mode(drive, 255, pio, NULL);
- (void) hpt3xx_tune_chipset(drive, (XFER_PIO_0 + pio));
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+ (void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
}
-/*
- * This allows the configuration of ide_pci chipset registers
- * for cards that learn about the drive's UDMA, DMA, PIO capabilities
- * after the drive is reported by the OS. Initially for designed for
- * HPT366 UDMA chipset by HighPoint|Triones Technologies, Inc.
- *
- * check_in_drive_lists(drive, bad_ata66_4)
- * check_in_drive_lists(drive, bad_ata66_3)
- * check_in_drive_lists(drive, bad_ata33)
- *
- */
-static int config_chipset_for_dma (ide_drive_t *drive)
+static int hpt3xx_quirkproc(ide_drive_t *drive)
{
- u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive));
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
-
- if (!speed)
- return 0;
-
- /* If we don't have any timings we can't do a lot */
- if (info->speed == NULL)
- return 0;
-
- (void) hpt3xx_tune_chipset(drive, speed);
- return ide_dma_enable(drive);
-}
+ struct hd_driveid *id = drive->id;
+ const char **list = quirk_drives;
-static int hpt3xx_quirkproc (ide_drive_t *drive)
-{
- return ((int) check_in_drive_lists(drive, quirk_drives));
+ while (*list)
+ if (strstr(id->model, *list++))
+ return 1;
+ return 0;
}
-static void hpt3xx_intrproc (ide_drive_t *drive)
+static void hpt3xx_intrproc(ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = HWIF(drive);
if (drive->quirk_list)
return;
/* drives in the quirk_list may not like intr setups/cleanups */
- hwif->OUTB(drive->ctl|2, IDE_CONTROL_REG);
+ hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
}
-static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
+static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- struct pci_dev *dev = hwif->pci_dev;
+ ide_hwif_t *hwif = HWIF(drive);
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
if (drive->quirk_list) {
- if (info->revision >= 3) {
- u8 reg5a = 0;
- pci_read_config_byte(dev, 0x5a, ®5a);
- if (((reg5a & 0x10) >> 4) != mask)
- pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10));
+ if (info->chip_type >= HPT370) {
+ u8 scr1 = 0;
+
+ pci_read_config_byte(dev, 0x5a, &scr1);
+ if (((scr1 & 0x10) >> 4) != mask) {
+ if (mask)
+ scr1 |= 0x10;
+ else
+ scr1 &= ~0x10;
+ pci_write_config_byte(dev, 0x5a, scr1);
+ }
} else {
- if (mask) {
+ if (mask)
disable_irq(hwif->irq);
- } else {
- enable_irq(hwif->irq);
- }
+ else
+ enable_irq (hwif->irq);
}
- } else {
- if (IDE_CONTROL_REG)
- hwif->OUTB(mask ? (drive->ctl | 2) :
- (drive->ctl & ~2),
- IDE_CONTROL_REG);
- }
+ } else
+ hwif->OUTB(mask ? (drive->ctl | 2) : (drive->ctl & ~2),
+ IDE_CONTROL_REG);
}
-static int hpt366_config_drive_xfer_rate (ide_drive_t *drive)
+static int hpt366_config_drive_xfer_rate(ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
- struct hd_driveid *id = drive->id;
-
drive->init_speed = 0;
- if ((id->capability & 1) && drive->autodma) {
-
- if (ide_use_dma(drive)) {
- if (config_chipset_for_dma(drive))
- return hwif->ide_dma_on(drive);
- }
+ if (ide_tune_dma(drive))
+ return 0;
- goto fast_ata_pio;
+ if (ide_use_fast_pio(drive))
+ hpt3xx_tune_drive(drive, 255);
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
- hpt3xx_tune_drive(drive, 5);
- return hwif->ide_dma_off_quietly(drive);
- }
- /* IORDY not supported */
- return 0;
+ return -1;
}
/*
- * This is specific to the HPT366 UDMA bios chipset
+ * This is specific to the HPT366 UDMA chipset
* by HighPoint|Triones Technologies, Inc.
*/
-static int hpt366_ide_dma_lostirq (ide_drive_t *drive)
+static void hpt366_dma_lost_irq(ide_drive_t *drive)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- u8 reg50h = 0, reg52h = 0, reg5ah = 0;
-
- pci_read_config_byte(dev, 0x50, ®50h);
- pci_read_config_byte(dev, 0x52, ®52h);
- pci_read_config_byte(dev, 0x5a, ®5ah);
- printk("%s: (%s) reg50h=0x%02x, reg52h=0x%02x, reg5ah=0x%02x\n",
- drive->name, __FUNCTION__, reg50h, reg52h, reg5ah);
- if (reg5ah & 0x10)
- pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
- return __ide_dma_lostirq(drive);
+ struct pci_dev *dev = HWIF(drive)->pci_dev;
+ u8 mcr1 = 0, mcr3 = 0, scr1 = 0;
+
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ pci_read_config_byte(dev, 0x52, &mcr3);
+ pci_read_config_byte(dev, 0x5a, &scr1);
+ printk("%s: (%s) mcr1=0x%02x, mcr3=0x%02x, scr1=0x%02x\n",
+ drive->name, __FUNCTION__, mcr1, mcr3, scr1);
+ if (scr1 & 0x10)
+ pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
+ ide_dma_lost_irq(drive);
}
-static void hpt370_clear_engine (ide_drive_t *drive)
+static void hpt370_clear_engine(ide_drive_t *drive)
{
- u8 regstate = HWIF(drive)->channel ? 0x54 : 0x50;
- pci_write_config_byte(HWIF(drive)->pci_dev, regstate, 0x37);
+ ide_hwif_t *hwif = HWIF(drive);
+
+ pci_write_config_byte(hwif->pci_dev, hwif->select_data, 0x37);
udelay(10);
}
+static void hpt370_irq_timeout(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = HWIF(drive);
+ u16 bfifo = 0;
+ u8 dma_cmd;
+
+ pci_read_config_word(hwif->pci_dev, hwif->select_data + 2, &bfifo);
+ printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo & 0x1ff);
+
+ /* get DMA command mode */
+ dma_cmd = hwif->INB(hwif->dma_command);
+ /* stop DMA */
+ hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command);
+ hpt370_clear_engine(drive);
+}
+
static void hpt370_ide_dma_start(ide_drive_t *drive)
{
#ifdef HPT_RESET_STATE_ENGINE
ide_dma_start(drive);
}
-static int hpt370_ide_dma_end (ide_drive_t *drive)
+static int hpt370_ide_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- u8 dma_stat = hwif->INB(hwif->dma_status);
+ u8 dma_stat = hwif->INB(hwif->dma_status);
if (dma_stat & 0x01) {
/* wait a little */
udelay(20);
dma_stat = hwif->INB(hwif->dma_status);
+ if (dma_stat & 0x01)
+ hpt370_irq_timeout(drive);
}
- if ((dma_stat & 0x01) != 0)
- /* fallthrough */
- (void) HWIF(drive)->ide_dma_timeout(drive);
-
return __ide_dma_end(drive);
}
-static void hpt370_lostirq_timeout (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- u8 bfifo = 0, reginfo = hwif->channel ? 0x56 : 0x52;
- u8 dma_stat = 0, dma_cmd = 0;
-
- pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo);
- printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo);
- hpt370_clear_engine(drive);
- /* get dma command mode */
- dma_cmd = hwif->INB(hwif->dma_command);
- /* stop dma */
- hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command);
- dma_stat = hwif->INB(hwif->dma_status);
- /* clear errors */
- hwif->OUTB(dma_stat | 0x6, hwif->dma_status);
-}
-
-static int hpt370_ide_dma_timeout (ide_drive_t *drive)
+static void hpt370_dma_timeout(ide_drive_t *drive)
{
- hpt370_lostirq_timeout(drive);
- hpt370_clear_engine(drive);
- return __ide_dma_timeout(drive);
-}
-
-static int hpt370_ide_dma_lostirq (ide_drive_t *drive)
-{
- hpt370_lostirq_timeout(drive);
- hpt370_clear_engine(drive);
- return __ide_dma_lostirq(drive);
+ hpt370_irq_timeout(drive);
+ ide_dma_timeout(drive);
}
/* returns 1 if DMA IRQ issued, 0 otherwise */
{
ide_hwif_t *hwif = HWIF(drive);
u16 bfifo = 0;
- u8 reginfo = hwif->channel ? 0x56 : 0x52;
- u8 dma_stat;
+ u8 dma_stat;
- pci_read_config_word(hwif->pci_dev, reginfo, &bfifo);
+ pci_read_config_word(hwif->pci_dev, hwif->select_data + 2, &bfifo);
if (bfifo & 0x1FF) {
// printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
return 0;
}
- dma_stat = hwif->INB(hwif->dma_status);
+ dma_stat = inb(hwif->dma_status);
/* return 1 if INTR asserted */
- if ((dma_stat & 4) == 4)
+ if (dma_stat & 4)
return 1;
if (!drive->waiting_for_dma)
return 0;
}
-static int hpt374_ide_dma_end (ide_drive_t *drive)
+static int hpt374_ide_dma_end(ide_drive_t *drive)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
ide_hwif_t *hwif = HWIF(drive);
- u8 msc_stat = 0, mscreg = hwif->channel ? 0x54 : 0x50;
- u8 bwsr_stat = 0, bwsr_mask = hwif->channel ? 0x02 : 0x01;
-
- pci_read_config_byte(dev, 0x6a, &bwsr_stat);
- pci_read_config_byte(dev, mscreg, &msc_stat);
- if ((bwsr_stat & bwsr_mask) == bwsr_mask)
- pci_write_config_byte(dev, mscreg, msc_stat|0x30);
+ struct pci_dev *dev = hwif->pci_dev;
+ u8 mcr = 0, mcr_addr = hwif->select_data;
+ u8 bwsr = 0, mask = hwif->channel ? 0x02 : 0x01;
+
+ pci_read_config_byte(dev, 0x6a, &bwsr);
+ pci_read_config_byte(dev, mcr_addr, &mcr);
+ if (bwsr & mask)
+ pci_write_config_byte(dev, mcr_addr, mcr | 0x30);
return __ide_dma_end(drive);
}
/**
- * hpt372n_set_clock - perform clock switching dance
- * @drive: Drive to switch
- * @mode: Switching mode (0x21 for write, 0x23 otherwise)
+ * hpt3xxn_set_clock - perform clock switching dance
+ * @hwif: hwif to switch
+ * @mode: clocking mode (0x21 for write, 0x23 otherwise)
*
- * Switch the DPLL clock on the HPT372N devices. This is a
- * right mess.
+ * Switch the DPLL clock on the HPT3xxN devices. This is a right mess.
*/
-
-static void hpt372n_set_clock(ide_drive_t *drive, int mode)
+
+static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode)
{
- ide_hwif_t *hwif = HWIF(drive);
-
- /* FIXME: should we check for DMA active and BUG() */
+ u8 scr2 = hwif->INB(hwif->dma_master + 0x7b);
+
+ if ((scr2 & 0x7f) == mode)
+ return;
+
/* Tristate the bus */
- outb(0x80, hwif->dma_base+0x73);
- outb(0x80, hwif->dma_base+0x77);
-
+ hwif->OUTB(0x80, hwif->dma_master + 0x73);
+ hwif->OUTB(0x80, hwif->dma_master + 0x77);
+
/* Switch clock and reset channels */
- outb(mode, hwif->dma_base+0x7B);
- outb(0xC0, hwif->dma_base+0x79);
-
- /* Reset state machines */
- outb(0x37, hwif->dma_base+0x70);
- outb(0x37, hwif->dma_base+0x74);
-
+ hwif->OUTB(mode, hwif->dma_master + 0x7b);
+ hwif->OUTB(0xc0, hwif->dma_master + 0x79);
+
+ /*
+ * Reset the state machines.
+ * NOTE: avoid accidentally enabling the disabled channels.
+ */
+ hwif->OUTB(hwif->INB(hwif->dma_master + 0x70) | 0x32,
+ hwif->dma_master + 0x70);
+ hwif->OUTB(hwif->INB(hwif->dma_master + 0x74) | 0x32,
+ hwif->dma_master + 0x74);
+
/* Complete reset */
- outb(0x00, hwif->dma_base+0x79);
-
+ hwif->OUTB(0x00, hwif->dma_master + 0x79);
+
/* Reconnect channels to bus */
- outb(0x00, hwif->dma_base+0x73);
- outb(0x00, hwif->dma_base+0x77);
+ hwif->OUTB(0x00, hwif->dma_master + 0x73);
+ hwif->OUTB(0x00, hwif->dma_master + 0x77);
}
/**
- * hpt372n_rw_disk - prepare for I/O
+ * hpt3xxn_rw_disk - prepare for I/O
* @drive: drive for command
* @rq: block request structure
*
- * This is called when a disk I/O is issued to the 372N.
+ * This is called when a disk I/O is issued to HPT3xxN.
* We need it because of the clock switching.
*/
-static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq)
-{
- ide_hwif_t *hwif = drive->hwif;
- int wantclock;
-
- wantclock = rq_data_dir(rq) ? 0x23 : 0x21;
-
- if (hwif->config_data != wantclock) {
- hpt372n_set_clock(drive, wantclock);
- hwif->config_data = wantclock;
- }
-}
-
-/*
- * Since SUN Cobalt is attempting to do this operation, I should disclose
- * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
- * HOTSWAP ATA Infrastructure.
- */
-
-static void hpt3xx_reset (ide_drive_t *drive)
+static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq)
{
-}
-
-static int hpt3xx_tristate (ide_drive_t * drive, int state)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40;
- u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
-
- pci_read_config_byte(dev, 0x59, ®59h);
- pci_read_config_byte(dev, state_reg, ®XXh);
-
- if (state) {
- (void) ide_do_reset(drive);
- pci_write_config_byte(dev, state_reg, regXXh|0x80);
- pci_write_config_byte(dev, 0x59, reg59h|reset);
- } else {
- pci_write_config_byte(dev, 0x59, reg59h & ~(reset));
- pci_write_config_byte(dev, state_reg, regXXh & ~(0x80));
- (void) ide_do_reset(drive);
- }
- return 0;
+ hpt3xxn_set_clock(HWIF(drive), rq_data_dir(rq) ? 0x23 : 0x21);
}
/*
- * set/get power state for a drive.
- * turning the power off does the following things:
- * 1) soft-reset the drive
- * 2) tri-states the ide bus
+ * Set/get power state for a drive.
+ * NOTE: affects both drives on each channel.
*
- * when we turn things back on, we need to re-initialize things.
+ * When we turn the power back on, we need to re-initialize things.
*/
#define TRISTATE_BIT 0x8000
-static int hpt370_busproc(ide_drive_t * drive, int state)
+
+static int hpt3xx_busproc(ide_drive_t *drive, int state)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
- u8 tristate = 0, resetmask = 0, bus_reg = 0;
- u16 tri_reg;
+ u8 mcr_addr = hwif->select_data + 2;
+ u8 resetmask = hwif->channel ? 0x80 : 0x40;
+ u8 bsr2 = 0;
+ u16 mcr = 0;
hwif->bus_state = state;
- if (hwif->channel) {
- /* secondary channel */
- tristate = 0x56;
- resetmask = 0x80;
- } else {
- /* primary channel */
- tristate = 0x52;
- resetmask = 0x40;
- }
-
- /* grab status */
- pci_read_config_word(dev, tristate, &tri_reg);
- pci_read_config_byte(dev, 0x59, &bus_reg);
+ /* Grab the status. */
+ pci_read_config_word(dev, mcr_addr, &mcr);
+ pci_read_config_byte(dev, 0x59, &bsr2);
- /* set the state. we don't set it if we don't need to do so.
- * make sure that the drive knows that it has failed if it's off */
+ /*
+ * Set the state. We don't set it if we don't need to do so.
+ * Make sure that the drive knows that it has failed if it's off.
+ */
switch (state) {
case BUSSTATE_ON:
- hwif->drives[0].failures = 0;
- hwif->drives[1].failures = 0;
- if ((bus_reg & resetmask) == 0)
+ if (!(bsr2 & resetmask))
return 0;
- tri_reg &= ~TRISTATE_BIT;
- bus_reg &= ~resetmask;
- break;
+ hwif->drives[0].failures = hwif->drives[1].failures = 0;
+
+ pci_write_config_byte(dev, 0x59, bsr2 & ~resetmask);
+ pci_write_config_word(dev, mcr_addr, mcr & ~TRISTATE_BIT);
+ return 0;
case BUSSTATE_OFF:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask))
+ if ((bsr2 & resetmask) && !(mcr & TRISTATE_BIT))
return 0;
- tri_reg &= ~TRISTATE_BIT;
- bus_reg |= resetmask;
+ mcr &= ~TRISTATE_BIT;
break;
case BUSSTATE_TRISTATE:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask))
+ if ((bsr2 & resetmask) && (mcr & TRISTATE_BIT))
return 0;
- tri_reg |= TRISTATE_BIT;
- bus_reg |= resetmask;
+ mcr |= TRISTATE_BIT;
break;
+ default:
+ return -EINVAL;
}
- pci_write_config_byte(dev, 0x59, bus_reg);
- pci_write_config_word(dev, tristate, tri_reg);
+ hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
+ hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
+
+ pci_write_config_word(dev, mcr_addr, mcr);
+ pci_write_config_byte(dev, 0x59, bsr2 | resetmask);
return 0;
}
-static void __devinit hpt366_clocking(ide_hwif_t *hwif)
+/**
+ * hpt37x_calibrate_dpll - calibrate the DPLL
+ * @dev: PCI device
+ *
+ * Perform a calibration cycle on the DPLL.
+ * Returns 1 if this succeeds
+ */
+static int __devinit hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high)
{
- u32 reg1 = 0;
- struct hpt_info *info = ide_get_hwifdata(hwif);
+ u32 dpll = (f_high << 16) | f_low | 0x100;
+ u8 scr2;
+ int i;
- pci_read_config_dword(hwif->pci_dev, 0x40, ®1);
+ pci_write_config_dword(dev, 0x5c, dpll);
- /* detect bus speed by looking at control reg timing: */
- switch((reg1 >> 8) & 7) {
- case 5:
- info->speed = forty_base_hpt366;
- break;
- case 9:
- info->speed = twenty_five_base_hpt366;
- break;
- case 7:
- default:
- info->speed = thirty_three_base_hpt366;
+ /* Wait for oscillator ready */
+ for(i = 0; i < 0x5000; ++i) {
+ udelay(50);
+ pci_read_config_byte(dev, 0x5b, &scr2);
+ if (scr2 & 0x80)
break;
}
+ /* See if it stays ready (we'll just bail out if it's not yet) */
+ for(i = 0; i < 0x1000; ++i) {
+ pci_read_config_byte(dev, 0x5b, &scr2);
+ /* DPLL destabilized? */
+ if(!(scr2 & 0x80))
+ return 0;
+ }
+ /* Turn off tuning, we have the DPLL set */
+ pci_read_config_dword (dev, 0x5c, &dpll);
+ pci_write_config_dword(dev, 0x5c, (dpll & ~0x100));
+ return 1;
}
-static void __devinit hpt37x_clocking(ide_hwif_t *hwif)
+static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
{
- struct hpt_info *info = ide_get_hwifdata(hwif);
- struct pci_dev *dev = hwif->pci_dev;
- int adjust, i;
- u16 freq;
- u32 pll;
- u8 reg5bh;
-
+ struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
+ unsigned long io_base = pci_resource_start(dev, 4);
+ u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
+ enum ata_clock clock;
+
+ if (info == NULL) {
+ printk(KERN_ERR "%s: out of memory!\n", name);
+ return -ENOMEM;
+ }
+
/*
- * default to pci clock. make sure MA15/16 are set to output
- * to prevent drives having problems with 40-pin cables. Needed
- * for some drives such as IBM-DTLA which will not enter ready
- * state on reset when PDIAG is a input.
- *
- * ToDo: should we set 0x21 when using PLL mode ?
+ * Copy everything from a static "template" structure
+ * to just allocated per-chip hpt_info structure.
*/
- pci_write_config_byte(dev, 0x5b, 0x23);
+ *info = *(struct hpt_info *)pci_get_drvdata(dev);
/*
- * set up the PLL. we need to adjust it so that it's stable.
- * freq = Tpll * 192 / Tpci
- *
- * Todo. For non x86 should probably check the dword is
- * set to 0xABCDExxx indicating the BIOS saved f_CNT
+ * FIXME: Not portable. Also, why do we enable the ROM in the first place?
+ * We don't seem to be using it.
*/
- pci_read_config_word(dev, 0x78, &freq);
- freq &= 0x1FF;
-
+ if (dev->resource[PCI_ROM_RESOURCE].start)
+ pci_write_config_dword(dev, PCI_ROM_ADDRESS,
+ dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
+
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+ pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+ pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
/*
- * The 372N uses different PCI clock information and has
- * some other complications
- * On PCI33 timing we must clock switch
- * On PCI66 timing we must NOT use the PCI clock
- *
- * Currently we always set up the PLL for the 372N
+ * First, try to estimate the PCI clock frequency...
*/
-
- if(info->flags & IS_372N)
- {
- printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n");
- if(freq < 0x55)
- pll = F_LOW_PCI_33;
- else if(freq < 0x70)
- pll = F_LOW_PCI_40;
- else if(freq < 0x7F)
- pll = F_LOW_PCI_50;
- else
- pll = F_LOW_PCI_66;
-
- printk(KERN_INFO "FREQ: %d PLL: %d\n", freq, pll);
-
- /* We always use the pll not the PCI clock on 372N */
- }
- else
- {
- if(freq < 0x9C)
- pll = F_LOW_PCI_33;
- else if(freq < 0xb0)
- pll = F_LOW_PCI_40;
- else if(freq <0xc8)
- pll = F_LOW_PCI_50;
- else
- pll = F_LOW_PCI_66;
-
- if (pll == F_LOW_PCI_33) {
- if (info->revision >= 8)
- info->speed = thirty_three_base_hpt374;
- else if (info->revision >= 5)
- info->speed = thirty_three_base_hpt372;
- else if (info->revision >= 4)
- info->speed = thirty_three_base_hpt370a;
- else
- info->speed = thirty_three_base_hpt370;
- printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n");
- } else if (pll == F_LOW_PCI_40) {
- /* Unsupported */
- } else if (pll == F_LOW_PCI_50) {
- if (info->revision >= 8)
- info->speed = fifty_base_hpt370a;
- else if (info->revision >= 5)
- info->speed = fifty_base_hpt372;
- else if (info->revision >= 4)
- info->speed = fifty_base_hpt370a;
- else
- info->speed = fifty_base_hpt370a;
- printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n");
- } else {
- if (info->revision >= 8) {
- printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n");
+ if (info->chip_type >= HPT370) {
+ u8 scr1 = 0;
+ u16 f_cnt = 0;
+ u32 temp = 0;
+
+ /* Interrupt force enable. */
+ pci_read_config_byte(dev, 0x5a, &scr1);
+ if (scr1 & 0x10)
+ pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
+
+ /*
+ * HighPoint does this for HPT372A.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (info->chip_type == HPT372A)
+ outb(0x0e, io_base + 0x9c);
+
+ /*
+ * Default to PCI clock. Make sure MA15/16 are set to output
+ * to prevent drives having problems with 40-pin cables.
+ */
+ pci_write_config_byte(dev, 0x5b, 0x23);
+
+ /*
+ * We'll have to read f_CNT value in order to determine
+ * the PCI clock frequency according to the following ratio:
+ *
+ * f_CNT = Fpci * 192 / Fdpll
+ *
+ * First try reading the register in which the HighPoint BIOS
+ * saves f_CNT value before reprogramming the DPLL from its
+ * default setting (which differs for the various chips).
+ * NOTE: This register is only accessible via I/O space.
+ *
+ * In case the signature check fails, we'll have to resort to
+ * reading the f_CNT register itself in hopes that nobody has
+ * touched the DPLL yet...
+ */
+ temp = inl(io_base + 0x90);
+ if ((temp & 0xFFFFF000) != 0xABCDE000) {
+ int i;
+
+ printk(KERN_WARNING "%s: no clock data saved by BIOS\n",
+ name);
+
+ /* Calculate the average value of f_CNT. */
+ for (temp = i = 0; i < 128; i++) {
+ pci_read_config_word(dev, 0x78, &f_cnt);
+ temp += f_cnt & 0x1ff;
+ mdelay(1);
}
- else if (info->revision >= 5)
- info->speed = sixty_six_base_hpt372;
- else if (info->revision >= 4)
- info->speed = sixty_six_base_hpt370a;
- else
- info->speed = sixty_six_base_hpt370;
- printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n");
+ f_cnt = temp / 128;
+ } else
+ f_cnt = temp & 0x1ff;
+
+ dpll_clk = info->dpll_clk;
+ pci_clk = (f_cnt * dpll_clk) / 192;
+
+ /* Clamp PCI clock to bands. */
+ if (pci_clk < 40)
+ pci_clk = 33;
+ else if(pci_clk < 45)
+ pci_clk = 40;
+ else if(pci_clk < 55)
+ pci_clk = 50;
+ else
+ pci_clk = 66;
+
+ printk(KERN_INFO "%s: DPLL base: %d MHz, f_CNT: %d, "
+ "assuming %d MHz PCI\n", name, dpll_clk, f_cnt, pci_clk);
+ } else {
+ u32 itr1 = 0;
+
+ pci_read_config_dword(dev, 0x40, &itr1);
+
+ /* Detect PCI clock by looking at cmd_high_time. */
+ switch((itr1 >> 8) & 0x07) {
+ case 0x09:
+ pci_clk = 40;
+ break;
+ case 0x05:
+ pci_clk = 25;
+ break;
+ case 0x07:
+ default:
+ pci_clk = 33;
+ break;
}
}
-
- /*
- * only try the pll if we don't have a table for the clock
- * speed that we're running at. NOTE: the internal PLL will
- * result in slow reads when using a 33MHz PCI clock. we also
- * don't like to use the PLL because it will cause glitches
- * on PRST/SRST when the HPT state engine gets reset.
- *
- * ToDo: Use 66MHz PLL when ATA133 devices are present on a
- * 372 device so we can get ATA133 support
- */
- if (info->speed)
- goto init_hpt37X_done;
- info->flags |= PLL_MODE;
-
+ /* Let's assume we'll use PCI clock for the ATA clock... */
+ switch (pci_clk) {
+ case 25:
+ clock = ATA_CLOCK_25MHZ;
+ break;
+ case 33:
+ default:
+ clock = ATA_CLOCK_33MHZ;
+ break;
+ case 40:
+ clock = ATA_CLOCK_40MHZ;
+ break;
+ case 50:
+ clock = ATA_CLOCK_50MHZ;
+ break;
+ case 66:
+ clock = ATA_CLOCK_66MHZ;
+ break;
+ }
+
/*
- * FIXME: make this work correctly, esp with 372N as per
- * reference driver code.
+ * Only try the DPLL if we don't have a table for the PCI clock that
+ * we are running at for HPT370/A, always use it for anything newer...
*
- * adjust PLL based upon PCI clock, enable it, and wait for
- * stabilization.
+ * NOTE: Using the internal DPLL results in slow reads on 33 MHz PCI.
+ * We also don't like using the DPLL because this causes glitches
+ * on PRST-/SRST- when the state engine gets reset...
*/
- adjust = 0;
- freq = (pll < F_LOW_PCI_50) ? 2 : 4;
- while (adjust++ < 6) {
- pci_write_config_dword(dev, 0x5c, (freq + pll) << 16 |
- pll | 0x100);
-
- /* wait for clock stabilization */
- for (i = 0; i < 0x50000; i++) {
- pci_read_config_byte(dev, 0x5b, ®5bh);
- if (reg5bh & 0x80) {
- /* spin looking for the clock to destabilize */
- for (i = 0; i < 0x1000; ++i) {
- pci_read_config_byte(dev, 0x5b,
- ®5bh);
- if ((reg5bh & 0x80) == 0)
- goto pll_recal;
- }
- pci_read_config_dword(dev, 0x5c, &pll);
- pci_write_config_dword(dev, 0x5c,
- pll & ~0x100);
- pci_write_config_byte(dev, 0x5b, 0x21);
- if (info->revision >= 8)
- info->speed = fifty_base_hpt370a;
- else if (info->revision >= 5)
- info->speed = fifty_base_hpt372;
- else if (info->revision >= 4)
- info->speed = fifty_base_hpt370a;
- else
- info->speed = fifty_base_hpt370a;
- printk("HPT37X: using 50MHz internal PLL\n");
- goto init_hpt37X_done;
- }
+ if (info->chip_type >= HPT374 || info->settings[clock] == NULL) {
+ u16 f_low, delta = pci_clk < 50 ? 2 : 4;
+ int adjust;
+
+ /*
+ * Select 66 MHz DPLL clock only if UltraATA/133 mode is
+ * supported/enabled, use 50 MHz DPLL clock otherwise...
+ */
+ if (info->max_mode == 0x04) {
+ dpll_clk = 66;
+ clock = ATA_CLOCK_66MHZ;
+ } else if (dpll_clk) { /* HPT36x chips don't have DPLL */
+ dpll_clk = 50;
+ clock = ATA_CLOCK_50MHZ;
}
- if (!pci_get_drvdata(dev)) {
- printk("No Clock Stabilization!!!\n");
- return;
+
+ if (info->settings[clock] == NULL) {
+ printk(KERN_ERR "%s: unknown bus timing!\n", name);
+ kfree(info);
+ return -EIO;
}
-pll_recal:
- if (adjust & 1)
- pll -= (adjust >> 1);
- else
- pll += (adjust >> 1);
- }
-
-init_hpt37X_done:
- if (!info->speed)
- printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n",
- (info->flags & IS_372N)?"N":"", pll, freq);
- /* reset state engine */
- pci_write_config_byte(dev, 0x50, 0x37);
- pci_write_config_byte(dev, 0x54, 0x37);
- udelay(100);
-}
-static int __devinit init_hpt37x(struct pci_dev *dev)
-{
- u8 reg5ah;
+ /* Select the DPLL clock. */
+ pci_write_config_byte(dev, 0x5b, 0x21);
- pci_read_config_byte(dev, 0x5a, ®5ah);
- /* interrupt force enable */
- pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
- return 0;
-}
+ /*
+ * Adjust the DPLL based upon PCI clock, enable it,
+ * and wait for stabilization...
+ */
+ f_low = (pci_clk * 48) / dpll_clk;
-static int __devinit init_hpt366(struct pci_dev *dev)
-{
- u32 reg1 = 0;
- u8 drive_fast = 0;
+ for (adjust = 0; adjust < 8; adjust++) {
+ if(hpt37x_calibrate_dpll(dev, f_low, f_low + delta))
+ break;
- /*
- * Disable the "fast interrupt" prediction.
- */
- pci_read_config_byte(dev, 0x51, &drive_fast);
- if (drive_fast & 0x80)
- pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
- pci_read_config_dword(dev, 0x40, ®1);
-
- return 0;
-}
+ /*
+ * See if it'll settle at a fractionally different clock
+ */
+ if (adjust & 1)
+ f_low -= adjust >> 1;
+ else
+ f_low += adjust >> 1;
+ }
+ if (adjust == 8) {
+ printk(KERN_ERR "%s: DPLL did not stabilize!\n", name);
+ kfree(info);
+ return -EIO;
+ }
-static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
-{
- int ret = 0;
+ printk("%s: using %d MHz DPLL clock\n", name, dpll_clk);
+ } else {
+ /* Mark the fact that we're not using the DPLL. */
+ dpll_clk = 0;
+
+ printk("%s: using %d MHz PCI clock\n", name, pci_clk);
+ }
/*
- * FIXME: Not portable. Also, why do we enable the ROM in the first place?
- * We don't seem to be using it.
+ * Advance the table pointer to a slot which points to the list
+ * of the register values settings matching the clock being used.
*/
- if (dev->resource[PCI_ROM_RESOURCE].start)
- pci_write_config_dword(dev, PCI_ROM_ADDRESS,
- dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
+ info->settings += clock;
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
- pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
- pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+ /* Store the clock frequencies. */
+ info->dpll_clk = dpll_clk;
+ info->pci_clk = pci_clk;
- if (hpt_revision(dev) >= 3)
- ret = init_hpt37x(dev);
- else
- ret = init_hpt366(dev);
+ /* Point to this chip's own instance of the hpt_info structure. */
+ pci_set_drvdata(dev, info);
- if (ret)
- return ret;
+ if (info->chip_type >= HPT370) {
+ u8 mcr1, mcr4;
+
+ /*
+ * Reset the state engines.
+ * NOTE: Avoid accidentally enabling the disabled channels.
+ */
+ pci_read_config_byte (dev, 0x50, &mcr1);
+ pci_read_config_byte (dev, 0x54, &mcr4);
+ pci_write_config_byte(dev, 0x50, (mcr1 | 0x32));
+ pci_write_config_byte(dev, 0x54, (mcr4 | 0x32));
+ udelay(100);
+ }
+
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (info->chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
+
+ outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c);
return dev->irq;
}
static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 ata66 = 0, regmask = (hwif->channel) ? 0x01 : 0x02;
-
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
+ int serialize = HPT_SERIALIZE_IO;
+ u8 scr1 = 0, ata66 = (hwif->channel) ? 0x01 : 0x02;
+ u8 chip_type = info->chip_type;
+ u8 new_mcr, old_mcr = 0;
+
+ /* Cache the channel's MISC. control registers' offset */
+ hwif->select_data = hwif->channel ? 0x54 : 0x50;
+
hwif->tuneproc = &hpt3xx_tune_drive;
hwif->speedproc = &hpt3xx_tune_chipset;
hwif->quirkproc = &hpt3xx_quirkproc;
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
-
- if(info->flags & IS_372N)
- hwif->rw_disk = &hpt372n_rw_disk;
+ hwif->busproc = &hpt3xx_busproc;
+ hwif->udma_filter = &hpt3xx_udma_filter;
/*
- * The HPT37x uses the CBLID pins as outputs for MA15/MA16
- * address lines to access an external eeprom. To read valid
- * cable detect state the pins must be enabled as inputs.
+ * HPT3xxN chips have some complications:
+ *
+ * - on 33 MHz PCI we must clock switch
+ * - on 66 MHz PCI we must NOT use the PCI clock
*/
- if (info->revision >= 8 && (PCI_FUNC(dev->devfn) & 1)) {
+ if (chip_type >= HPT372N && info->dpll_clk && info->pci_clk < 66) {
/*
- * HPT374 PCI function 1
- * - set bit 15 of reg 0x52 to enable TCBLID as input
- * - set bit 15 of reg 0x56 to enable FCBLID as input
+ * Clock is shared between the channels,
+ * so we'll have to serialize them... :-(
*/
- u16 mcr3, mcr6;
- pci_read_config_word(dev, 0x52, &mcr3);
- pci_read_config_word(dev, 0x56, &mcr6);
- pci_write_config_word(dev, 0x52, mcr3 | 0x8000);
- pci_write_config_word(dev, 0x56, mcr6 | 0x8000);
- /* now read cable id register */
- pci_read_config_byte(dev, 0x5a, &ata66);
- pci_write_config_word(dev, 0x52, mcr3);
- pci_write_config_word(dev, 0x56, mcr6);
- } else if (info->revision >= 3) {
- /*
- * HPT370/372 and 374 pcifn 0
- * - clear bit 0 of 0x5b to enable P/SCBLID as inputs
- */
- u8 scr2;
- pci_read_config_byte(dev, 0x5b, &scr2);
- pci_write_config_byte(dev, 0x5b, scr2 & ~1);
- /* now read cable id register */
- pci_read_config_byte(dev, 0x5a, &ata66);
- pci_write_config_byte(dev, 0x5b, scr2);
- } else {
- pci_read_config_byte(dev, 0x5a, &ata66);
+ serialize = 1;
+ hwif->rw_disk = &hpt3xxn_rw_disk;
}
-#ifdef DEBUG
- printk("HPT366: reg5ah=0x%02x ATA-%s Cable Port%d\n",
- ata66, (ata66 & regmask) ? "33" : "66",
- PCI_FUNC(hwif->pci_dev->devfn));
-#endif /* DEBUG */
-
-#ifdef HPT_SERIALIZE_IO
- /* serialize access to this device */
- if (hwif->mate)
+ /* Serialize access to this device if needed */
+ if (serialize && hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
+
+ /*
+ * Disable the "fast interrupt" prediction. Don't hold off
+ * on interrupts. (== 0x01 despite what the docs say)
+ */
+ pci_read_config_byte(dev, hwif->select_data + 1, &old_mcr);
+
+ if (info->chip_type >= HPT374)
+ new_mcr = old_mcr & ~0x07;
+ else if (info->chip_type >= HPT370) {
+ new_mcr = old_mcr;
+ new_mcr &= ~0x02;
+
+#ifdef HPT_DELAY_INTERRUPT
+ new_mcr &= ~0x01;
+#else
+ new_mcr |= 0x01;
#endif
+ } else /* HPT366 and HPT368 */
+ new_mcr = old_mcr & ~0x80;
- if (info->revision >= 3) {
- u8 reg5ah = 0;
- pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
- /*
- * set up ioctl for power status.
- * note: power affects both
- * drives on each channel
- */
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt370_busproc;
- } else if (info->revision >= 2) {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- } else {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- }
+ if (new_mcr != old_mcr)
+ pci_write_config_byte(dev, hwif->select_data + 1, new_mcr);
if (!hwif->dma_base) {
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
+ hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
return;
}
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
- if (!(hwif->udma_four))
- hwif->udma_four = ((ata66 & regmask) ? 0 : 1);
- hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
-
- if (info->revision >= 8) {
- hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
- hwif->ide_dma_end = &hpt374_ide_dma_end;
- } else if (info->revision >= 5) {
- hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
- hwif->ide_dma_end = &hpt374_ide_dma_end;
- } else if (info->revision >= 3) {
- hwif->dma_start = &hpt370_ide_dma_start;
- hwif->ide_dma_end = &hpt370_ide_dma_end;
- hwif->ide_dma_timeout = &hpt370_ide_dma_timeout;
- hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq;
- } else if (info->revision >= 2)
- hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
- else
- hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
+ /*
+ * The HPT37x uses the CBLID pins as outputs for MA15/MA16
+ * address lines to access an external EEPROM. To read valid
+ * cable detect state the pins must be enabled as inputs.
+ */
+ if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
+ /*
+ * HPT374 PCI function 1
+ * - set bit 15 of reg 0x52 to enable TCBLID as input
+ * - set bit 15 of reg 0x56 to enable FCBLID as input
+ */
+ u8 mcr_addr = hwif->select_data + 2;
+ u16 mcr;
+
+ pci_read_config_word (dev, mcr_addr, &mcr);
+ pci_write_config_word(dev, mcr_addr, (mcr | 0x8000));
+ /* now read cable id register */
+ pci_read_config_byte (dev, 0x5a, &scr1);
+ pci_write_config_word(dev, mcr_addr, mcr);
+ } else if (chip_type >= HPT370) {
+ /*
+ * HPT370/372 and 374 pcifn 0
+ * - clear bit 0 of reg 0x5b to enable P/SCBLID as inputs
+ */
+ u8 scr2 = 0;
+
+ pci_read_config_byte (dev, 0x5b, &scr2);
+ pci_write_config_byte(dev, 0x5b, (scr2 & ~1));
+ /* now read cable id register */
+ pci_read_config_byte (dev, 0x5a, &scr1);
+ pci_write_config_byte(dev, 0x5b, scr2);
+ } else
+ pci_read_config_byte (dev, 0x5a, &scr1);
+
+ if (!hwif->udma_four)
+ hwif->udma_four = (scr1 & ata66) ? 0 : 1;
+
+ hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
+
+ if (chip_type >= HPT374) {
+ hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
+ hwif->ide_dma_end = &hpt374_ide_dma_end;
+ } else if (chip_type >= HPT370) {
+ hwif->dma_start = &hpt370_ide_dma_start;
+ hwif->ide_dma_end = &hpt370_ide_dma_end;
+ hwif->dma_timeout = &hpt370_dma_timeout;
+ } else
+ hwif->dma_lost_irq = &hpt366_dma_lost_irq;
if (!noautodma)
hwif->autodma = 1;
- hwif->drives[0].autodma = hwif->autodma;
- hwif->drives[1].autodma = hwif->autodma;
+ hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
{
- struct hpt_info *info = ide_get_hwifdata(hwif);
- u8 masterdma = 0, slavedma = 0;
- u8 dma_new = 0, dma_old = 0;
- u8 primary = hwif->channel ? 0x4b : 0x43;
- u8 secondary = hwif->channel ? 0x4f : 0x47;
+ struct pci_dev *dev = hwif->pci_dev;
+ u8 masterdma = 0, slavedma = 0;
+ u8 dma_new = 0, dma_old = 0;
unsigned long flags;
- if (!dmabase)
- return;
-
- if(info->speed == NULL) {
- printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n");
- return;
- }
-
- dma_old = hwif->INB(dmabase+2);
+ dma_old = hwif->INB(dmabase + 2);
local_irq_save(flags);
dma_new = dma_old;
- pci_read_config_byte(hwif->pci_dev, primary, &masterdma);
- pci_read_config_byte(hwif->pci_dev, secondary, &slavedma);
+ pci_read_config_byte(dev, hwif->channel ? 0x4b : 0x43, &masterdma);
+ pci_read_config_byte(dev, hwif->channel ? 0x4f : 0x47, &slavedma);
if (masterdma & 0x30) dma_new |= 0x20;
- if (slavedma & 0x30) dma_new |= 0x40;
+ if ( slavedma & 0x30) dma_new |= 0x40;
if (dma_new != dma_old)
- hwif->OUTB(dma_new, dmabase+2);
+ hwif->OUTB(dma_new, dmabase + 2);
local_irq_restore(flags);
ide_setup_dma(hwif, dmabase, 8);
}
-/*
- * We "borrow" this hook in order to set the data structures
- * up early enough before dma or init_hwif calls are made.
- */
-
-static void __devinit init_iops_hpt366(ide_hwif_t *hwif)
+static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
{
- struct hpt_info *info = kzalloc(sizeof(struct hpt_info), GFP_KERNEL);
- unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4);
- u8 did, rid;
+ struct pci_dev *dev2;
- if(info == NULL) {
- printk(KERN_WARNING "hpt366: out of memory.\n");
- return;
- }
- ide_set_hwifdata(hwif, info);
+ if (PCI_FUNC(dev->devfn) & 1)
+ return -ENODEV;
- if(dmabase) {
- did = inb(dmabase + 0x22);
- rid = inb(dmabase + 0x28);
+ pci_set_drvdata(dev, &hpt374);
- if((did == 4 && rid == 6) || (did == 5 && rid > 1))
- info->flags |= IS_372N;
+ if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
+ int ret;
+
+ pci_set_drvdata(dev2, &hpt374);
+
+ if (dev2->irq != dev->irq) {
+ /* FIXME: we need a core pci_set_interrupt() */
+ dev2->irq = dev->irq;
+ printk(KERN_WARNING "%s: PCI config space interrupt "
+ "fixed.\n", d->name);
+ }
+ ret = ide_setup_pci_devices(dev, dev2, d);
+ if (ret < 0)
+ pci_dev_put(dev2);
+ return ret;
}
+ return ide_setup_pci_device(dev, d);
+}
- info->revision = hpt_revision(hwif->pci_dev);
+static int __devinit init_setup_hpt372n(struct pci_dev *dev, ide_pci_device_t *d)
+{
+ pci_set_drvdata(dev, &hpt372n);
- if (info->revision >= 3)
- hpt37x_clocking(hwif);
- else
- hpt366_clocking(hwif);
+ return ide_setup_pci_device(dev, d);
}
-static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
+static int __devinit init_setup_hpt371(struct pci_dev *dev, ide_pci_device_t *d)
{
- struct pci_dev *findev = NULL;
+ struct hpt_info *info;
+ u8 rev = 0, mcr1 = 0;
- if (PCI_FUNC(dev->devfn) & 1)
- return -ENODEV;
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
+
+ if (rev > 1) {
+ d->name = "HPT371N";
+
+ info = &hpt371n;
+ } else
+ info = &hpt371;
+
+ /*
+ * HPT371 chips physically have only one channel, the secondary one,
+ * but the primary channel registers do exist! Go figure...
+ * So, we manually disable the non-existing channel here
+ * (if the BIOS hasn't done this already).
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x04)
+ pci_write_config_byte(dev, 0x50, mcr1 & ~0x04);
+
+ pci_set_drvdata(dev, info);
- while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) {
- if ((findev->vendor == dev->vendor) &&
- (findev->device == dev->device) &&
- ((findev->devfn - dev->devfn) == 1) &&
- (PCI_FUNC(findev->devfn) & 1)) {
- if (findev->irq != dev->irq) {
- /* FIXME: we need a core pci_set_interrupt() */
- findev->irq = dev->irq;
- printk(KERN_WARNING "%s: pci-config space interrupt "
- "fixed.\n", d->name);
- }
- return ide_setup_pci_devices(dev, findev, d);
- }
- }
return ide_setup_pci_device(dev, d);
}
-static int __devinit init_setup_hpt37x(struct pci_dev *dev, ide_pci_device_t *d)
+static int __devinit init_setup_hpt372a(struct pci_dev *dev, ide_pci_device_t *d)
{
+ struct hpt_info *info;
+ u8 rev = 0;
+
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
+
+ if (rev > 1) {
+ d->name = "HPT372N";
+
+ info = &hpt372n;
+ } else
+ info = &hpt372a;
+ pci_set_drvdata(dev, info);
+
+ return ide_setup_pci_device(dev, d);
+}
+
+static int __devinit init_setup_hpt302(struct pci_dev *dev, ide_pci_device_t *d)
+{
+ struct hpt_info *info;
+ u8 rev = 0;
+
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
+
+ if (rev > 1) {
+ d->name = "HPT302N";
+
+ info = &hpt302n;
+ } else
+ info = &hpt302;
+ pci_set_drvdata(dev, info);
+
return ide_setup_pci_device(dev, d);
}
static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d)
{
- struct pci_dev *findev = NULL;
- u8 pin1 = 0, pin2 = 0;
- unsigned int class_rev;
- char *chipset_names[] = {"HPT366", "HPT366", "HPT368",
- "HPT370", "HPT370A", "HPT372",
- "HPT372N" };
+ struct pci_dev *dev2;
+ u8 rev = 0;
+ static char *chipset_names[] = { "HPT366", "HPT366", "HPT368",
+ "HPT370", "HPT370A", "HPT372",
+ "HPT372N" };
+ static struct hpt_info *info[] = { &hpt36x, &hpt36x, &hpt36x,
+ &hpt370, &hpt370a, &hpt372,
+ &hpt372n };
if (PCI_FUNC(dev->devfn) & 1)
return -ENODEV;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
+ pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
- if(dev->device == PCI_DEVICE_ID_TTI_HPT372N)
- class_rev = 6;
+ if (rev > 6)
+ rev = 6;
- if(class_rev <= 6)
- d->name = chipset_names[class_rev];
-
- switch(class_rev) {
- case 6:
- case 5:
- case 4:
- case 3:
- goto init_single;
- default:
- break;
- }
+ d->name = chipset_names[rev];
+
+ pci_set_drvdata(dev, info[rev]);
+ if (rev > 2)
+ goto init_single;
+
+ /*
+ * HPT36x chips have one channel per function and have
+ * both channel enable bits located differently and visible
+ * to both functions -- really stupid design decision... :-(
+ * Bit 4 is for the primary channel, bit 5 for the secondary.
+ */
d->channels = 1;
+ d->enablebits[0].mask = d->enablebits[0].val = 0x10;
- pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
- while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) {
- if ((findev->vendor == dev->vendor) &&
- (findev->device == dev->device) &&
- ((findev->devfn - dev->devfn) == 1) &&
- (PCI_FUNC(findev->devfn) & 1)) {
- pci_read_config_byte(findev, PCI_INTERRUPT_PIN, &pin2);
- if ((pin1 != pin2) && (dev->irq == findev->irq)) {
- d->bootable = ON_BOARD;
- printk("%s: onboard version of chipset, "
- "pin1=%d pin2=%d\n", d->name,
- pin1, pin2);
- }
- return ide_setup_pci_devices(dev, findev, d);
+ if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
+ u8 mcr1 = 0, pin1 = 0, pin2 = 0;
+ int ret;
+
+ pci_set_drvdata(dev2, info[rev]);
+
+ /*
+ * Now we'll have to force both channels enabled if
+ * at least one of them has been enabled by BIOS...
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x30)
+ pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
+
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
+ pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
+ if (pin1 != pin2 && dev->irq == dev2->irq) {
+ d->bootable = ON_BOARD;
+ printk("%s: onboard version of chipset, pin1=%d pin2=%d\n",
+ d->name, pin1, pin2);
}
+ ret = ide_setup_pci_devices(dev, dev2, d);
+ if (ret < 0)
+ pci_dev_put(dev2);
+ return ret;
}
init_single:
return ide_setup_pci_device(dev, d);
.name = "HPT366",
.init_setup = init_setup_hpt366,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
.extra = 240
},{ /* 1 */
.name = "HPT372A",
- .init_setup = init_setup_hpt37x,
+ .init_setup = init_setup_hpt372a,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
+ .extra = 240
},{ /* 2 */
.name = "HPT302",
- .init_setup = init_setup_hpt37x,
+ .init_setup = init_setup_hpt302,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
+ .extra = 240
},{ /* 3 */
.name = "HPT371",
- .init_setup = init_setup_hpt37x,
+ .init_setup = init_setup_hpt371,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
+ .extra = 240
},{ /* 4 */
.name = "HPT374",
.init_setup = init_setup_hpt374,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2, /* 4 */
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
+ .extra = 240
},{ /* 5 */
.name = "HPT372N",
- .init_setup = init_setup_hpt37x,
+ .init_setup = init_setup_hpt372n,
.init_chipset = init_chipset_hpt366,
- .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2, /* 4 */
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
+ .extra = 240
}
};
*
* Called when the PCI registration layer (or the IDE initialization)
* finds a device matching our IDE device tables.
+ *
+ * NOTE: since we'll have to modify some fields of the ide_pci_device_t
+ * structure depending on the chip's revision, we'd better pass a local
+ * copy down the call chain...
*/
-
static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_pci_device_t *d = &hpt366_chipsets[id->driver_data];
+ ide_pci_device_t d = hpt366_chipsets[id->driver_data];
- return d->init_setup(dev, d);
+ return d.init_setup(dev, &d);
}
static struct pci_device_id hpt366_pci_tbl[] = {
.probe = hpt366_init_one,
};
-static int hpt366_ide_init(void)
+static int __init hpt366_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
projects / linux-2.6-omap-h63xx.git / blobdiff