/*
- * linux/drivers/ide/setup-pci.c Version 1.10 2002/08/19
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 1995-1998 Mark Lord
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*
- * Copyright (c) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- *
- * Copyright (c) 1995-1998 Mark Lord
* May be copied or modified under the terms of the GNU General Public License
*/
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+static void ide_pci_clear_simplex(unsigned long dma_base, const char *name)
+{
+ u8 dma_stat = inb(dma_base + 2);
+
+ outb(dma_stat & 0x60, dma_base + 2);
+ dma_stat = inb(dma_base + 2);
+ if (dma_stat & 0x80)
+ printk(KERN_INFO "%s: simplex device: DMA forced\n", name);
+}
+
/**
* ide_get_or_set_dma_base - setup BMIBA
* @d: IDE port info
static unsigned long ide_get_or_set_dma_base(const struct ide_port_info *d, ide_hwif_t *hwif)
{
- unsigned long dma_base = 0;
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long dma_base = 0;
+ u8 dma_stat = 0;
if (hwif->mmio)
return hwif->dma_base;
if (hwif->channel)
dma_base += 8;
- if ((d->host_flags & IDE_HFLAG_CS5520) == 0) {
- u8 simplex_stat = 0;
-
- switch(dev->device) {
- case PCI_DEVICE_ID_AL_M5219:
- case PCI_DEVICE_ID_AL_M5229:
- case PCI_DEVICE_ID_AMD_VIPER_7409:
- case PCI_DEVICE_ID_CMD_643:
- case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
- case PCI_DEVICE_ID_REVOLUTION:
- simplex_stat = inb(dma_base + 2);
- outb(simplex_stat & 0x60, dma_base + 2);
- simplex_stat = inb(dma_base + 2);
- if (simplex_stat & 0x80) {
- printk(KERN_INFO "%s: simplex device: "
- "DMA forced\n",
- d->name);
- }
- break;
- default:
- /*
- * If the device claims "simplex" DMA,
- * this means only one of the two interfaces
- * can be trusted with DMA at any point in time.
- * So we should enable DMA only on one of the
- * two interfaces.
- */
- simplex_stat = hwif->INB(dma_base + 2);
- if (simplex_stat & 0x80) {
- /* simplex device? */
-/*
- * At this point we haven't probed the drives so we can't make the
- * appropriate decision. Really we should defer this problem
- * until we tune the drive then try to grab DMA ownership if we want
- * to be the DMA end. This has to be become dynamic to handle hot
- * plug.
- */
- if (hwif->mate && hwif->mate->dma_base) {
- printk(KERN_INFO "%s: simplex device: "
- "DMA disabled\n",
- d->name);
- dma_base = 0;
- }
- }
- }
+ if (d->host_flags & IDE_HFLAG_CS5520)
+ goto out;
+
+ if (d->host_flags & IDE_HFLAG_CLEAR_SIMPLEX) {
+ ide_pci_clear_simplex(dma_base, d->name);
+ goto out;
+ }
+
+ /*
+ * If the device claims "simplex" DMA, this means that only one of
+ * the two interfaces can be trusted with DMA at any point in time
+ * (so we should enable DMA only on one of the two interfaces).
+ *
+ * FIXME: At this point we haven't probed the drives so we can't make
+ * the appropriate decision. Really we should defer this problem until
+ * we tune the drive then try to grab DMA ownership if we want to be
+ * the DMA end. This has to be become dynamic to handle hot-plug.
+ */
+ dma_stat = hwif->INB(dma_base + 2);
+ if ((dma_stat & 0x80) && hwif->mate && hwif->mate->dma_base) {
+ printk(KERN_INFO "%s: simplex device: DMA disabled\n", d->name);
+ dma_base = 0;
}
+out:
return dma_base;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
* @d: IDE port info
*
* Enable the IDE PCI device. We attempt to enable the device in full
- * but if that fails then we only need BAR4 so we will enable that.
+ * but if that fails then we only need IO space. The PCI code should
+ * have setup the proper resources for us already for controllers in
+ * legacy mode.
*
* Returns zero on success or an error code
*/
int ret;
if (pci_enable_device(dev)) {
- ret = pci_enable_device_bars(dev, 1 << 4);
+ ret = pci_enable_device_io(dev);
if (ret < 0) {
printk(KERN_WARNING "%s: (ide_setup_pci_device:) "
"Could not enable device.\n", d->name);
* ide_hwif_configure - configure an IDE interface
* @dev: PCI device holding interface
* @d: IDE port info
- * @mate: Paired interface if any
+ * @port: port number
+ * @irq: PCI IRQ
*
* Perform the initial set up for the hardware interface structure. This
* is done per interface port rather than per PCI device. There may be
* Returns the new hardware interface structure, or NULL on a failure
*/
-static ide_hwif_t *ide_hwif_configure(struct pci_dev *dev, const struct ide_port_info *d, ide_hwif_t *mate, int port, int irq)
+static ide_hwif_t *ide_hwif_configure(struct pci_dev *dev,
+ const struct ide_port_info *d,
+ unsigned int port, int irq)
{
unsigned long ctl = 0, base = 0;
ide_hwif_t *hwif;
hwif->noprobe = oldnoprobe;
- hwif->pci_dev = dev;
+ hwif->dev = &dev->dev;
hwif->cds = d;
- hwif->channel = port;
- if (mate) {
- hwif->mate = mate;
- mate->mate = hwif;
- }
return hwif;
}
+#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
/**
* ide_hwif_setup_dma - configure DMA interface
- * @dev: PCI device
- * @d: IDE port info
* @hwif: IDE interface
+ * @d: IDE port info
*
* Set up the DMA base for the interface. Enable the master bits as
* necessary and attempt to bring the device DMA into a ready to use
* state
*/
-static void ide_hwif_setup_dma(struct pci_dev *dev, const struct ide_port_info *d, ide_hwif_t *hwif)
+void ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d)
{
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u16 pcicmd;
pci_read_config_word(dev, PCI_COMMAND, &pcicmd);
if (d->init_dma) {
d->init_dma(hwif, dma_base);
} else {
- ide_setup_dma(hwif, dma_base, 8);
+ ide_setup_dma(hwif, dma_base);
}
} else {
printk(KERN_INFO "%s: %s Bus-Master DMA disabled "
"(BIOS)\n", hwif->name, d->name);
}
}
-#endif /* CONFIG_BLK_DEV_IDEDMA_PCI*/
}
+#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
/**
* ide_setup_pci_controller - set up IDE PCI
void ide_pci_setup_ports(struct pci_dev *dev, const struct ide_port_info *d, int pciirq, u8 *idx)
{
int channels = (d->host_flags & IDE_HFLAG_SINGLE) ? 1 : 2, port;
- ide_hwif_t *hwif, *mate = NULL;
+ ide_hwif_t *hwif;
u8 tmp;
/*
continue; /* port not enabled */
}
- if ((hwif = ide_hwif_configure(dev, d, mate, port, pciirq)) == NULL)
+ hwif = ide_hwif_configure(dev, d, port, pciirq);
+ if (hwif == NULL)
continue;
*(idx + port) = hwif->index;
-
- if (d->init_iops)
- d->init_iops(hwif);
-
- if ((d->host_flags & IDE_HFLAG_NO_DMA) == 0)
- ide_hwif_setup_dma(dev, d, hwif);
-
- if ((!hwif->irq && (d->host_flags & IDE_HFLAG_LEGACY_IRQS)) ||
- (d->host_flags & IDE_HFLAG_FORCE_LEGACY_IRQS))
- hwif->irq = port ? 15 : 14;
-
- hwif->host_flags = d->host_flags;
- hwif->pio_mask = d->pio_mask;
-
- if ((d->host_flags & IDE_HFLAG_SERIALIZE) && hwif->mate)
- hwif->mate->serialized = hwif->serialized = 1;
-
- if (d->host_flags & IDE_HFLAG_IO_32BIT) {
- hwif->drives[0].io_32bit = 1;
- hwif->drives[1].io_32bit = 1;
- }
-
- if (d->host_flags & IDE_HFLAG_UNMASK_IRQS) {
- hwif->drives[0].unmask = 1;
- hwif->drives[1].unmask = 1;
- }
-
- if (hwif->dma_base) {
- hwif->swdma_mask = d->swdma_mask;
- hwif->mwdma_mask = d->mwdma_mask;
- hwif->ultra_mask = d->udma_mask;
- }
-
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
-
- if (d->host_flags & IDE_HFLAG_RQSIZE_256)
- hwif->rqsize = 256;
-
- if (d->init_hwif)
- /* Call chipset-specific routine
- * for each enabled hwif
- */
- d->init_hwif(hwif);
-
- mate = hwif;
}
}
ret = do_ide_setup_pci_device(dev, d, &idx[0], 1);
if (ret >= 0)
- ide_device_add(idx);
+ ide_device_add(idx, d);
return ret;
}
goto out;
}
- ide_device_add(idx);
+ ide_device_add(idx, d);
out:
return ret;
}
projects / linux-2.6-omap-h63xx.git / blobdiff