# drivers/mtd/maps/Kconfig
-# $Id: Kconfig,v 1.61 2005/11/07 11:14:26 gleixner Exp $
menu "Mapping drivers for chip access"
depends on MTD!=n
particular board as well as the bus width, either statically
with config options or at run-time.
+ To compile this driver as a module, choose M here: the
+ module will be called physmap.
+
config MTD_PHYSMAP_START
hex "Physical start address of flash mapping"
depends on MTD_PHYSMAP
help
This is the total width of the data bus of the flash devices
in octets. For example, if you have a data bus width of 32
- bits, you would set the bus width octect value to 4. This is
+ bits, you would set the bus width octet value to 4. This is
used internally by the CFI drivers.
Ignore this option if you use run-time physmap configuration
(i.e., run-time calling physmap_configure()).
depends on PMC_MSP && MTD_CFI
select MTD_PARTITIONS
help
- This provides a 'mapping' driver which support the way
- in which user-programmable flash chips are connected on the
- PMC-Sierra MSP eval/demo boards
+ This provides a 'mapping' driver which supports the way
+ in which user-programmable flash chips are connected on the
+ PMC-Sierra MSP eval/demo boards.
choice
- prompt "Maximum mappable memory avialable for flash IO"
+ prompt "Maximum mappable memory available for flash IO"
depends on MTD_PMC_MSP_EVM
default MSP_FLASH_MAP_LIMIT_32M
config MTD_SUN_UFLASH
tristate "Sun Microsystems userflash support"
- depends on SPARC && MTD_CFI
+ depends on SPARC && MTD_CFI && PCI
help
This provides a 'mapping' driver which supports the way in
which user-programmable flash chips are connected on various
Sun Microsystems boardsets. This driver will require CFI support
in the kernel, so if you did not enable CFI previously, do that now.
-config MTD_PNC2000
- tristate "CFI Flash device mapped on Photron PNC-2000"
- depends on X86 && MTD_CFI && MTD_PARTITIONS
- help
- PNC-2000 is the name of Network Camera product from PHOTRON
- Ltd. in Japan. It uses CFI-compliant flash.
-
config MTD_SC520CDP
tristate "CFI Flash device mapped on AMD SC520 CDP"
depends on X86 && MTD_CFI && MTD_CONCAT
More info at
<http://www.arcomcontrols.com/products/icp/pc104/processors/SBC_GX1.htm>.
-config MTD_LUBBOCK
- tristate "CFI Flash device mapped on Intel Lubbock XScale eval board"
- depends on ARCH_LUBBOCK && MTD_CFI_INTELEXT && MTD_PARTITIONS
- help
- This provides a driver for the on-board flash of the Intel
- 'Lubbock' XScale evaluation board.
-
-config MTD_MAINSTONE
- tristate "CFI Flash device mapped on Intel Mainstone XScale eval board"
- depends on MACH_MAINSTONE && MTD_CFI_INTELEXT
+config MTD_PXA2XX
+ tristate "CFI Flash device mapped on Intel XScale PXA2xx based boards"
+ depends on (PXA25x || PXA27x) && MTD_CFI_INTELEXT
select MTD_PARTITIONS
help
- This provides a driver for the on-board flash of the Intel
- 'Mainstone PXA27x evaluation board.
+ This provides a driver for the NOR flash attached to a PXA2xx chip.
config MTD_OCTAGON
tristate "JEDEC Flash device mapped on Octagon 5066 SBC"
help
Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards
-config MTD_MTX1
- tristate "4G Systems MTX-1 Flash device"
- depends on MIPS_MTX1 && MTD_CFI
- help
- Flash memory access on 4G Systems MTX-1 Board. If you have one of
- these boards and would like to use the flash chips on it, say 'Y'.
-
config MTD_DILNETPC
tristate "CFI Flash device mapped on DIL/Net PC"
depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT
config MTD_WALNUT
tristate "Flash device mapped on IBM 405GP Walnut"
- depends on MTD_JEDECPROBE && WALNUT
+ depends on MTD_JEDECPROBE && WALNUT && !PPC_MERGE
help
This enables access routines for the flash chips on the IBM 405GP
Walnut board. If you have one of these boards and would like to
config MTD_EBONY
tristate "Flash devices mapped on IBM 440GP Ebony"
- depends on MTD_JEDECPROBE && EBONY
+ depends on MTD_JEDECPROBE && EBONY && !PPC_MERGE
help
This enables access routines for the flash chips on the IBM 440GP
Ebony board. If you have one of these boards and would like to
config MTD_OCOTEA
tristate "Flash devices mapped on IBM 440GX Ocotea"
- depends on MTD_CFI && OCOTEA
+ depends on MTD_CFI && OCOTEA && !PPC_MERGE
help
This enables access routines for the flash chips on the IBM 440GX
Ocotea board. If you have one of these boards and would like to
Redwood board. If you have one of these boards and would like to
use the flash chips on it, say 'Y'.
-config MTD_TQM834x
- tristate "Flash device mapped on TQ Components TQM834x Boards"
- depends on MTD_CFI && TQM834x
- help
- This enables access routines for the flash chips on the
- TQ Components TQM834x boards. If you have one of these boards
- and would like to use the flash chips on it, say 'Y'.
-
-config MTD_OCELOT
- tristate "Momenco Ocelot boot flash device"
- depends on MOMENCO_OCELOT
- help
- This enables access routines for the boot flash device and for the
- NVRAM on the Momenco Ocelot board. If you have one of these boards
- and would like access to either of these, say 'Y'.
-
config MTD_SOLUTIONENGINE
tristate "CFI Flash device mapped on Hitachi SolutionEngine"
- depends on SUPERH && MTD_CFI && MTD_REDBOOT_PARTS
+ depends on SUPERH && SOLUTION_ENGINE && MTD_CFI && MTD_REDBOOT_PARTS
help
This enables access to the flash chips on the Hitachi SolutionEngine and
similar boards. Say 'Y' if you are building a kernel for such a board.
This enables access to the flash chips on the Hynix evaluation boards.
If you have such a board, say 'Y'.
-config MTD_MPC1211
- tristate "CFI Flash device mapped on Interface MPC-1211"
- depends on SH_MPC1211 && MTD_CFI
- help
- This enables access to the flash chips on the Interface MPC-1211(CTP/PCI/MPC-SH02).
- If you have such a board, say 'Y'.
-
config MTD_OMAP_NOR
tristate "TI OMAP board mappings"
depends on MTD_CFI && ARCH_OMAP
If unsure, say N.
+config MTD_BFIN_ASYNC
+ tristate "Blackfin BF533-STAMP Flash Chip Support"
+ depends on BFIN533_STAMP && MTD_CFI
+ select MTD_PARTITIONS
+ default y
+ help
+ Map driver which allows for simultaneous utilization of
+ ethernet and CFI parallel flash.
+
+ If compiled as a module, it will be called bfin-async-flash.
+
config MTD_UCLINUX
tristate "Generic uClinux RAM/ROM filesystem support"
depends on MTD_PARTITIONS && !MMU
help
Map driver for Dy-4 SVME/DMV-182 board.
-config MTD_BAST
- tristate "Map driver for Simtec BAST (EB2410ITX) or Thorcom VR1000"
- depends on ARCH_BAST || MACH_VR1000
- select MTD_PARTITIONS
- select MTD_MAP_BANK_WIDTH_16
- select MTD_JEDECPROBE
- help
- Map driver for NOR flash on the Simtec BAST (EB2410ITX), or the
- Thorcom VR1000
-
- Note, this driver *cannot* over-ride the WP link on the
- board, or currently detect the state of the link.
-
-config MTD_BAST_MAXSIZE
- int "Maximum size for BAST flash area (MiB)"
- depends on MTD_BAST
- default "4"
-
config MTD_SHARP_SL
- bool "ROM mapped on Sharp SL Series"
+ tristate "ROM mapped on Sharp SL Series"
depends on ARCH_PXA
help
This enables access to the flash chip on the Sharp SL Series of PDAs.
+config MTD_INTEL_VR_NOR
+ tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
+ depends on PCI
+ help
+ Map driver for a NOR flash bank located on the Expansion Bus of the
+ Intel Vermilion Range chipset.
+
config MTD_PLATRAM
tristate "Map driver for platform device RAM (mtd-ram)"
select MTD_RAM