help
This enables support for accessing all type of NAND flash
devices. For further information see
- <http://www.linux-mtd.infradead.org/tech/nand.html>.
+ <http://www.linux-mtd.infradead.org/doc/nand.html>.
config MTD_NAND_VERIFY_WRITE
bool "Verify NAND page writes"
NAND flash device internally checks only bits transitioning
from 1 to 0. There is a rare possibility that even though the
device thinks the write was successful, a bit could have been
- flipped accidentaly due to device wear or something else.
+ flipped accidentally due to device wear or something else.
+
+config MTD_NAND_ECC_SMC
+ bool "NAND ECC Smart Media byte order"
+ depends on MTD_NAND
+ default n
+ help
+ Software ECC according to the Smart Media Specification.
+ The original Linux implementation had byte 0 and 1 swapped.
config MTD_NAND_AUTCPU12
tristate "SmartMediaCard on autronix autcpu12 board"
help
If you had to ask, you don't have one. Say 'N'.
+config MTD_NAND_AMS_DELTA
+ tristate "NAND Flash device on Amstrad E3"
+ depends on MACH_AMS_DELTA && MTD_NAND
+ help
+ Support for NAND flash on Amstrad E3 (Delta).
+
config MTD_NAND_TOTO
tristate "NAND Flash device on TOTO board"
- depends on ARCH_OMAP && MTD_NAND
+ depends on ARCH_OMAP && MTD_NAND && BROKEN
help
Support for NAND flash on Texas Instruments Toto platform.
+config MTD_NAND_TS7250
+ tristate "NAND Flash device on TS-7250 board"
+ depends on MACH_TS72XX && MTD_NAND
+ help
+ Support for NAND flash on Technologic Systems TS-7250 platform.
+
config MTD_NAND_IDS
tristate
depends on MTD_NAND && SH_SOLUTION_ENGINE
select REED_SOLOMON
select REED_SOLOMON_DEC8
+ select BITREVERSE
help
This enables the driver for the Renesas Technology AG-AND
flash interface board (FROM_BOARD4)
config MTD_NAND_PPCHAMELEONEVB
tristate "NAND Flash device on PPChameleonEVB board"
- depends on PPCHAMELEONEVB && MTD_NAND
+ depends on PPCHAMELEONEVB && MTD_NAND && BROKEN
help
This enables the NAND flash driver on the PPChameleon EVB Board.
This enables the NAND flash controller on the S3C2410 and S3C2440
SoCs
- No board specfic support is done by this driver, each board
+ No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C2410_DEBUG
incorrect ECC generation, and if using these, the default of
software ECC is preferable.
- If you lay down a device with the hardware ECC, then you will
- currently not be able to switch to software, as there is no
- implementation for ECC method used by the S3C2410
+config MTD_NAND_NDFC
+ tristate "NDFC NanD Flash Controller"
+ depends on MTD_NAND && 44x
+ select MTD_NAND_ECC_SMC
+ help
+ NDFC Nand Flash Controllers are integrated in EP44x SoCs
+
+config MTD_NAND_S3C2410_CLKSTOP
+ bool "S3C2410 NAND IDLE clock stop"
+ depends on MTD_NAND_S3C2410
+ default n
+ help
+ Stop the clock to the NAND controller when there is no chip
+ selected to save power. This will mean there is a small delay
+ when the is NAND chip selected or released, but will save
+ approximately 5mA of power when there is nothing happening.
config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
Even if you leave this disabled, you can enable BBT writes at module
load time (assuming you build diskonchip as a module) with the module
parameter "inftl_bbt_write=1".
-
- config MTD_NAND_SHARPSL
- bool "Support for NAND Flash on Sharp SL Series (C7xx + others)"
- depends on MTD_NAND && ARCH_PXA
-
- config MTD_NAND_NANDSIM
- bool "Support for NAND Flash Simulator"
- depends on MTD_NAND && MTD_PARTITIONS
+config MTD_NAND_SHARPSL
+ tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
+ depends on MTD_NAND && ARCH_PXA
+
+config MTD_NAND_BASLER_EXCITE
+ tristate "Support for NAND Flash on Basler eXcite"
+ depends on MTD_NAND && BASLER_EXCITE
+ help
+ This enables the driver for the NAND flash device found on the
+ Basler eXcite Smart Camera. If built as a module, the driver
+ will be named "excite_nandflash.ko".
+
+config MTD_NAND_CAFE
+ tristate "NAND support for OLPC CAFÉ chip"
+ depends on MTD_NAND && PCI
+ help
+ Use NAND flash attached to the CAFÉ chip designed for the $100
+ laptop.
+
+config MTD_NAND_CS553X
+ tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
+ depends on MTD_NAND && X86_32 && (X86_PC || X86_GENERICARCH)
+ help
+ The CS553x companion chips for the AMD Geode processor
+ include NAND flash controllers with built-in hardware ECC
+ capabilities; enabling this option will allow you to use
+ these. The driver will check the MSRs to verify that the
+ controller is enabled for NAND, and currently requires that
+ the controller be in MMIO mode.
+
+ If you say "m", the module will be called "cs553x_nand.ko".
+
+config MTD_NAND_AT91
+ bool "Support for NAND Flash / SmartMedia on AT91"
+ depends on MTD_NAND && ARCH_AT91
help
- The simulator may simulate verious NAND flash chips for the
+ Enables support for NAND Flash / Smart Media Card interface
+ on Atmel AT91 processors.
+
+config MTD_NAND_NANDSIM
+ tristate "Support for NAND Flash Simulator"
+ depends on MTD_NAND && MTD_PARTITIONS
+ help
+ The simulator may simulate various NAND flash chips for the
MTD nand layer.
-
+
endmenu