Merge branch 'master' into upstream

[linux-2.6-omap-h63xx.git] / drivers / net / Kconfig

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 68bc073b8b31f9e65cc300482cecb8db2f27a16a..7c826db84604a9d20d6a12b615d0abe850777625 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -447,6 +447,7 @@ config MIPS_GT96100ETH
 config MIPS_AU1X00_ENET
        bool "MIPS AU1000 Ethernet support"
        depends on NET_ETHERNET && SOC_AU1X00
+       select PHYLIB
        select CRC32
        help
          If you have an Alchemy Semi AU1X00 based system
@@ -853,6 +854,17 @@ config SMC9194
          <file:Documentation/networking/net-modules.txt>. The module
          will be called smc9194.
 
+config NET_NETX
+       tristate "NetX Ethernet support"
+       select MII
+       depends on NET_ETHERNET && ARCH_NETX
+       help
+         This is support for the Hilscher netX builtin Ethernet ports
+
+         To compile this driver as a module, choose M here and read
+         <file:Documentation/networking/net-modules.txt>. The module
+         will be called netx-eth.
+
 config DM9000
        tristate "DM9000 support"
        depends on (ARM || MIPS) && NET_ETHERNET
@@ -869,7 +881,7 @@ config SMC911X
        tristate "SMSC LAN911[5678] support"
        select CRC32
        select MII
-       depends on NET_ETHERNET
+       depends on NET_ETHERNET && ARCH_PXA
        help
          This is a driver for SMSC's LAN911x series of Ethernet chipsets
          including the new LAN9115, LAN9116, LAN9117, and LAN9118.
@@ -1375,8 +1387,8 @@ config APRICOT
          called apricot.
 
 config B44
-       tristate "Broadcom 4400 ethernet support (EXPERIMENTAL)"
-       depends on NET_PCI && PCI && EXPERIMENTAL
+       tristate "Broadcom 4400 ethernet support"
+       depends on NET_PCI && PCI
        select MII
        help
          If you have a network (Ethernet) controller of this type, say Y and
@@ -2179,6 +2191,8 @@ config TIGON3
 config BNX2
        tristate "Broadcom NetXtremeII support"
        depends on PCI
+       select CRC32
+       select ZLIB_INFLATE
        help
          This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
 
@@ -2187,7 +2201,7 @@ config BNX2
 
 config SPIDER_NET
        tristate "Spider Gigabit Ethernet driver"
-       depends on PCI && PPC_CELL
+       depends on PCI && PPC_IBM_CELL_BLADE
        select FW_LOADER
        help
          This driver supports the Gigabit Ethernet chips present on the
@@ -2195,11 +2209,11 @@ config SPIDER_NET
 
 config GIANFAR
        tristate "Gianfar Ethernet"
-       depends on 85xx || 83xx
+       depends on 85xx || 83xx || PPC_86xx
        select PHYLIB
        help
-         This driver supports the Gigabit TSEC on the MPC85xx 
-         family of chips, and the FEC on the 8540
+         This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+         and MPC86xx family of chips, and the FEC on the 8540.
 
 config GFAR_NAPI
        bool "NAPI Support"
@@ -2327,6 +2341,23 @@ config S2IO_NAPI
 
          If in doubt, say N.
 
+config MYRI10GE
+       tristate "Myricom Myri-10G Ethernet support"
+       depends on PCI
+       select FW_LOADER
+       select CRC32
+       ---help---
+         This driver supports Myricom Myri-10G Dual Protocol interface in
+         Ethernet mode. If the eeprom on your board is not recent enough,
+         you will need a newer firmware image.
+         You may get this image or more information, at:
+
+         <http://www.myri.com/Myri-10G/>
+
+         To compile this driver as a module, choose M here and read
+         <file:Documentation/networking/net-modules.txt>.  The module
+         will be called myri10ge.
+
 endmenu
 
 source "drivers/net/tokenring/Kconfig"
@@ -2478,6 +2509,7 @@ config PLIP
 
 config PPP
        tristate "PPP (point-to-point protocol) support"
+       select SLHC
        ---help---
          PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
          the same purpose: sending Internet traffic over telephone (and other
@@ -2658,6 +2690,7 @@ config SLIP
 config SLIP_COMPRESSED
        bool "CSLIP compressed headers"
        depends on SLIP
+       select SLHC
        ---help---
          This protocol is faster than SLIP because it uses compression on the
          TCP/IP headers (not on the data itself), but it has to be supported
@@ -2670,6 +2703,12 @@ config SLIP_COMPRESSED
          <http://www.tldp.org/docs.html#howto>, explains how to configure
          CSLIP. This won't enlarge your kernel.
 
+config SLHC
+       tristate
+       help
+         This option enables Van Jacobsen serial line header compression
+         routines.
+
 config SLIP_SMART
        bool "Keepalive and linefill"
        depends on SLIP