* it under the terms of the GNU General Public License as published by
* the Free Software Foundation.
*
- * The registers description starts with the regsister Access type followed
+ * The registers description starts with the register Access type followed
* by size in bits. For example [RW 32]. The access types are:
* R - Read only
* RC - Clear on read
was asserted. */
#define BRB1_REG_NUM_OF_FULL_CYCLES_0 0x600c8
#define BRB1_REG_NUM_OF_FULL_CYCLES_1 0x600cc
-#define BRB1_REG_NUM_OF_FULL_CYCLES_2 0x600d0
-#define BRB1_REG_NUM_OF_FULL_CYCLES_3 0x600d4
#define BRB1_REG_NUM_OF_FULL_CYCLES_4 0x600d8
/* [ST 32] The number of cycles that the pause signal towards MAC #0 was
asserted. */
#define BRB1_REG_NUM_OF_PAUSE_CYCLES_0 0x600b8
#define BRB1_REG_NUM_OF_PAUSE_CYCLES_1 0x600bc
-#define BRB1_REG_NUM_OF_PAUSE_CYCLES_2 0x600c0
-#define BRB1_REG_NUM_OF_PAUSE_CYCLES_3 0x600c4
/* [RW 10] Write client 0: De-assert pause threshold. */
#define BRB1_REG_PAUSE_HIGH_THRESHOLD_0 0x60078
#define BRB1_REG_PAUSE_HIGH_THRESHOLD_1 0x6007c
/* [RW 10] Write client 0: Assert pause threshold. */
#define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068
#define BRB1_REG_PAUSE_LOW_THRESHOLD_1 0x6006c
+/* [R 24] The number of full blocks occupied by port. */
+#define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094
/* [RW 1] Reset the design by software. */
#define BRB1_REG_SOFT_RESET 0x600dc
/* [R 5] Used to read the value of the XX protection CAM occupancy counter. */
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define CSEM_REG_INT_TABLE 0x200400
-#define CSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define CSEM_REG_MSG_NUM_FIC0 0x200000
#define DBG_REG_DBG_PRTY_MASK 0xc0a8
/* [R 1] Parity register #0 read */
#define DBG_REG_DBG_PRTY_STS 0xc09c
-/* [RW 2] debug only: These bits indicate the credit for PCI request type 4
- interface; MUST be configured AFTER pci_ext_buffer_strt_addr_lsb/msb are
- configured */
-#define DBG_REG_PCI_REQ_CREDIT 0xc120
/* [RW 32] Commands memory. The address to command X; row Y is to calculated
as 14*X+Y. */
#define DMAE_REG_CMD_MEM 0x102400
+#define DMAE_REG_CMD_MEM_SIZE 224
/* [RW 1] If 0 - the CRC-16c initial value is all zeroes; if 1 - the CRC-16c
initial value is all ones. */
#define DMAE_REG_CRC16C_INIT 0x10201c
#define HC_REG_ATTN_MSG1_ADDR_L 0x108020
#define HC_REG_ATTN_NUM_P0 0x108038
#define HC_REG_ATTN_NUM_P1 0x10803c
+#define HC_REG_COMMAND_REG 0x108180
#define HC_REG_CONFIG_0 0x108000
#define HC_REG_CONFIG_1 0x108004
#define HC_REG_FUNC_NUM_P0 0x1080ac
be asserted). */
#define MISC_REG_DRIVER_CONTROL_16 0xa5f0
#define MISC_REG_DRIVER_CONTROL_16_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_7 0xa3c8
/* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0
only. */
#define MISC_REG_E1HMF_MODE 0xa5f8
#define MISC_REG_GPIO 0xa490
/* [R 28] this field hold the last information that caused reserved
attention. bits [19:0] - address; [22:20] function; [23] reserved;
- [27:24] the master thatcaused the attention - according to the following
+ [27:24] the master that caused the attention - according to the following
encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
dbu; 8 = dmae */
#define MISC_REG_GRC_RSV_ATTN 0xa3c0
/* [R 28] this field hold the last information that caused timeout
attention. bits [19:0] - address; [22:20] function; [23] reserved;
- [27:24] the master thatcaused the attention - according to the following
+ [27:24] the master that caused the attention - according to the following
encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
dbu; 8 = dmae */
#define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4
is reset to 0x080; giving a default blink period of approximately 8Hz. */
#define NIG_REG_LED_CONTROL_BLINK_RATE_P0 0x10310
/* [RW 1] Port0: If set along with the
- nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0
+ ~nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0
bit and ~nig_registers_led_control_traffic_p0.led_control_traffic_p0 LED
bit; the Traffic LED will blink with the blink rate specified in
~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and
/* [RW 8] init credit counter for port0 in LLH */
#define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554
#define NIG_REG_LLH0_XCM_MASK 0x10130
+#define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc
/* [RW 2] Determine the classification participants. 0: no classification.1:
/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
for port0 */
#define NIG_REG_STAT0_BRB_DISCARD 0x105f0
+/* [R 32] Rx statistics : In user packets truncated due to BRB backpressure
+ for port0 */
+#define NIG_REG_STAT0_BRB_TRUNCATE 0x105f8
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1024 and 1522 bytes for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT0 0x10750
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1523 bytes and above for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT1 0x10760
/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
for port1 */
#define NIG_REG_STAT1_BRB_DISCARD 0x10628
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1024 and 1522 bytes for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT0 0x107a0
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1523 bytes and above for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT1 0x107b0
/* [WB_R 64] Rx statistics : User octets received for LP */
#define NIG_REG_STAT2_BRB_OCTET 0x107e0
#define NIG_REG_STATUS_INTERRUPT_PORT0 0x10328
#define PRS_REG_CFC_SEARCH_INITIAL_CREDIT 0x4011c
/* [RW 24] CID for port 0 if no match */
#define PRS_REG_CID_PORT_0 0x400fc
-#define PRS_REG_CID_PORT_1 0x40100
/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
load response is reset and packet type is 0. Used in packet start message
to TCM. */
#define PXP2_REG_HST_DATA_FIFO_STATUS 0x12047c
/* [R 7] Debug only: Number of used entries in the header FIFO */
#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
+#define PXP2_REG_PGL_ADDR_88_F0 0x120534
+#define PXP2_REG_PGL_ADDR_8C_F0 0x120538
+#define PXP2_REG_PGL_ADDR_90_F0 0x12053c
+#define PXP2_REG_PGL_ADDR_94_F0 0x120540
#define PXP2_REG_PGL_CONTROL0 0x120490
#define PXP2_REG_PGL_CONTROL1 0x120514
/* [RW 32] third dword data of expansion rom request. this register is
#define PXP2_REG_PSWRQ_SRC0_L2P 0x120054
#define PXP2_REG_PSWRQ_TM0_L2P 0x12001c
#define PXP2_REG_PSWRQ_TSDM0_L2P 0x1200e0
-/* [RW 25] Interrupt mask register #0 read/write */
-#define PXP2_REG_PXP2_INT_MASK 0x120578
-/* [R 25] Interrupt register #0 read */
-#define PXP2_REG_PXP2_INT_STS 0x12056c
-/* [RC 25] Interrupt register #0 read clear */
-#define PXP2_REG_PXP2_INT_STS_CLR 0x120570
+/* [RW 32] Interrupt mask register #0 read/write */
+#define PXP2_REG_PXP2_INT_MASK_0 0x120578
+/* [R 32] Interrupt register #0 read */
+#define PXP2_REG_PXP2_INT_STS_0 0x12056c
+#define PXP2_REG_PXP2_INT_STS_1 0x120608
+/* [RC 32] Interrupt register #0 read clear */
+#define PXP2_REG_PXP2_INT_STS_CLR_0 0x120570
/* [RW 32] Parity mask register #0 read/write */
#define PXP2_REG_PXP2_PRTY_MASK_0 0x120588
#define PXP2_REG_PXP2_PRTY_MASK_1 0x120598
/* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_QM_P_SIZE 0x120050
-/* [RW 1] 1' indicates that the RBC has finished configurating the PSWRQ */
+/* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */
#define PXP2_REG_RQ_RBC_DONE 0x1201b0
/* [RW 3] Max burst size filed for read requests port 0; 000 - 128B;
001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
buffer reaches this number has_payload will be asserted */
#define PXP2_REG_WR_DMAE_MPS 0x1205ec
-/* [RW 10] if Number of entries in dmae fifo will be higer than this
+/* [RW 10] if Number of entries in dmae fifo will be higher than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_DMAE_TH 0x120368
/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
buffer reaches this number has_payload will be asserted */
#define PXP2_REG_WR_TSDM_MPS 0x1205d4
-/* [RW 10] if Number of entries in usdmdp fifo will be higer than this
+/* [RW 10] if Number of entries in usdmdp fifo will be higher than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_USDMDP_TH 0x120348
#define QM_REG_QVOQIDX_97 0x16e490
#define QM_REG_QVOQIDX_98 0x16e494
#define QM_REG_QVOQIDX_99 0x16e498
-/* [R 24] Remaining pause timeout for queues 15-0 */
-#define QM_REG_REMAINPAUSETM0 0x168418
-/* [R 24] Remaining pause timeout for queues 31-16 */
-#define QM_REG_REMAINPAUSETM1 0x16841c
-/* [R 24] Remaining pause timeout for queues 47-32 */
-#define QM_REG_REMAINPAUSETM2 0x16e69c
-/* [R 24] Remaining pause timeout for queues 63-48 */
-#define QM_REG_REMAINPAUSETM3 0x16e6a0
-/* [R 24] Remaining pause timeout for queues 79-64 */
-#define QM_REG_REMAINPAUSETM4 0x16e6a4
-/* [R 24] Remaining pause timeout for queues 95-80 */
-#define QM_REG_REMAINPAUSETM5 0x16e6a8
-/* [R 24] Remaining pause timeout for queues 111-96 */
-#define QM_REG_REMAINPAUSETM6 0x16e6ac
-/* [R 24] Remaining pause timeout for queues 127-112 */
-#define QM_REG_REMAINPAUSETM7 0x16e6b0
/* [RW 1] Initialization bit command */
#define QM_REG_SOFT_RESET 0x168428
/* [RW 8] The credit cost per every task in the QM. A value per each VOQ */
#define XSEM_XSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
#define CFC_DEBUG1_REG_WRITE_AC (0x1<<4)
#define CFC_DEBUG1_REG_WRITE_AC_SIZE 4
-/* [R 1] debug only: This bit indicates wheter indicates that external
+/* [R 1] debug only: This bit indicates whether indicates that external
buffer was wrapped (oldest data was thrown); Relevant only when
~dbg_registers_debug_target=2 (PCI) & ~dbg_registers_full_mode=1 (wrap); */
#define DBG_REG_WRAP_ON_EXT_BUFFER 0xc124
#define DBG_REG_WRAP_ON_EXT_BUFFER_SIZE 1
-/* [R 1] debug only: This bit indicates wheter the internal buffer was
+/* [R 1] debug only: This bit indicates whether the internal buffer was
wrapped (oldest data was thrown) Relevant only when
~dbg_registers_debug_target=0 (internal buffer) */
#define DBG_REG_WRAP_ON_INT_BUFFER 0xc128
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define TSEM_REG_INT_TABLE 0x180400
-#define TSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define TSEM_REG_MSG_NUM_FIC0 0x180000
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define USEM_REG_INT_TABLE 0x300400
-#define USEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define USEM_REG_MSG_NUM_FIC0 0x300000
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define XSEM_REG_INT_TABLE 0x280400
-#define XSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define XSEM_REG_MSG_NUM_FIC0 0x280000
#define EMAC_MDIO_MODE_CLOCK_CNT (0x3fL<<16)
#define EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT 16
#define EMAC_MODE_25G_MODE (1L<<5)
-#define EMAC_MODE_ACPI_RCVD (1L<<20)
#define EMAC_MODE_HALF_DUPLEX (1L<<1)
-#define EMAC_MODE_MPKT (1L<<18)
-#define EMAC_MODE_MPKT_RCVD (1L<<19)
#define EMAC_MODE_PORT_GMII (2L<<2)
#define EMAC_MODE_PORT_MII (1L<<2)
#define EMAC_MODE_PORT_MII_10M (3L<<2)
#define EMAC_RX_MODE_PROMISCUOUS (1L<<8)
#define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31)
#define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3)
+#define EMAC_TX_MODE_FLOW_EN (1L<<4)
#define MISC_REGISTERS_GPIO_0 0
#define MISC_REGISTERS_GPIO_1 1
#define MISC_REGISTERS_GPIO_2 2
#define MISC_REGISTERS_GPIO_PORT_SHIFT 4
#define MISC_REGISTERS_GPIO_SET_POS 8
#define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7)
#define MISC_REGISTERS_RESET_REG_1_SET 0x584
#define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598
#define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0)
#define HW_LOCK_MAX_RESOURCE_VALUE 31
#define HW_LOCK_RESOURCE_8072_MDIO 0
#define HW_LOCK_RESOURCE_GPIO 1
+#define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3
#define HW_LOCK_RESOURCE_SPIO 2
+#define HW_LOCK_RESOURCE_UNDI 5
#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18)
#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31)
#define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9)
#define GRCBASE_MISC_AEU GRCBASE_MISC
-/*the offset of the configuration space in the pci core register*/
+/* offset of configuration space in the pci core register */
#define PCICFG_OFFSET 0x2000
#define PCICFG_VENDOR_ID_OFFSET 0x00
#define PCICFG_DEVICE_ID_OFFSET 0x02
#define PCICFG_COMMAND_OFFSET 0x04
+#define PCICFG_COMMAND_IO_SPACE (1<<0)
+#define PCICFG_COMMAND_MEM_SPACE (1<<1)
+#define PCICFG_COMMAND_BUS_MASTER (1<<2)
+#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3)
+#define PCICFG_COMMAND_MWI_CYCLES (1<<4)
+#define PCICFG_COMMAND_VGA_SNOOP (1<<5)
+#define PCICFG_COMMAND_PERR_ENA (1<<6)
+#define PCICFG_COMMAND_STEPPING (1<<7)
+#define PCICFG_COMMAND_SERR_ENA (1<<8)
+#define PCICFG_COMMAND_FAST_B2B (1<<9)
+#define PCICFG_COMMAND_INT_DISABLE (1<<10)
+#define PCICFG_COMMAND_RESERVED (0x1f<<11)
#define PCICFG_STATUS_OFFSET 0x06
-#define PCICFG_REVESION_ID 0x08
+#define PCICFG_REVESION_ID 0x08
#define PCICFG_CACHE_LINE_SIZE 0x0c
#define PCICFG_LATENCY_TIMER 0x0d
-#define PCICFG_BAR_1_LOW 0x10
-#define PCICFG_BAR_1_HIGH 0x14
-#define PCICFG_BAR_2_LOW 0x18
-#define PCICFG_BAR_2_HIGH 0x1c
-#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
+#define PCICFG_BAR_1_LOW 0x10
+#define PCICFG_BAR_1_HIGH 0x14
+#define PCICFG_BAR_2_LOW 0x18
+#define PCICFG_BAR_2_HIGH 0x1c
+#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
-#define PCICFG_INT_LINE 0x3c
-#define PCICFG_INT_PIN 0x3d
-#define PCICFG_PM_CSR_OFFSET 0x4c
-#define PCICFG_GRC_ADDRESS 0x78
-#define PCICFG_GRC_DATA 0x80
+#define PCICFG_INT_LINE 0x3c
+#define PCICFG_INT_PIN 0x3d
+#define PCICFG_PM_CAPABILITY 0x48
+#define PCICFG_PM_CAPABILITY_VERSION (0x3<<16)
+#define PCICFG_PM_CAPABILITY_CLOCK (1<<19)
+#define PCICFG_PM_CAPABILITY_RESERVED (1<<20)
+#define PCICFG_PM_CAPABILITY_DSI (1<<21)
+#define PCICFG_PM_CAPABILITY_AUX_CURRENT (0x7<<22)
+#define PCICFG_PM_CAPABILITY_D1_SUPPORT (1<<25)
+#define PCICFG_PM_CAPABILITY_D2_SUPPORT (1<<26)
+#define PCICFG_PM_CAPABILITY_PME_IN_D0 (1<<27)
+#define PCICFG_PM_CAPABILITY_PME_IN_D1 (1<<28)
+#define PCICFG_PM_CAPABILITY_PME_IN_D2 (1<<29)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_HOT (1<<30)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_COLD (1<<31)
+#define PCICFG_PM_CSR_OFFSET 0x4c
+#define PCICFG_PM_CSR_STATE (0x3<<0)
+#define PCICFG_PM_CSR_PME_ENABLE (1<<8)
+#define PCICFG_PM_CSR_PME_STATUS (1<<15)
+#define PCICFG_GRC_ADDRESS 0x78
+#define PCICFG_GRC_DATA 0x80
#define PCICFG_DEVICE_CONTROL 0xb4
#define PCICFG_LINK_CONTROL 0xbc
-#define PCICFG_COMMAND_IO_SPACE (1<<0)
-#define PCICFG_COMMAND_MEM_SPACE (1<<1)
-#define PCICFG_COMMAND_BUS_MASTER (1<<2)
-#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3)
-#define PCICFG_COMMAND_MWI_CYCLES (1<<4)
-#define PCICFG_COMMAND_VGA_SNOOP (1<<5)
-#define PCICFG_COMMAND_PERR_ENA (1<<6)
-#define PCICFG_COMMAND_STEPPING (1<<7)
-#define PCICFG_COMMAND_SERR_ENA (1<<8)
-#define PCICFG_COMMAND_FAST_B2B (1<<9)
-#define PCICFG_COMMAND_INT_DISABLE (1<<10)
-#define PCICFG_COMMAND_RESERVED (0x1f<<11)
-
-#define PCICFG_PM_CSR_STATE (0x3<<0)
-#define PCICFG_PM_CSR_PME_STATUS (1<<15)
#define BAR_USTRORM_INTMEM 0x400000
#define BAR_CSTRORM_INTMEM 0x410000
#define BAR_XSTRORM_INTMEM 0x420000
#define BAR_TSTRORM_INTMEM 0x430000
+/* for accessing the IGU in case of status block ACK */
#define BAR_IGU_INTMEM 0x440000
#define BAR_DOORBELL_OFFSET 0x800000
#define BAR_ME_REGISTER 0x450000
-
-#define GRC_CONFIG_2_SIZE_REG 0x408 /* config_2 offset */
-#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0)
+/* config_2 offset */
+#define GRC_CONFIG_2_SIZE_REG 0x408
+#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0)
#define PCI_CONFIG_2_BAR1_SIZE_DISABLED (0L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_64K (1L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_128K (2L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_256M (13L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_512M (14L<<0)
#define PCI_CONFIG_2_BAR1_SIZE_1G (15L<<0)
-#define PCI_CONFIG_2_BAR1_64ENA (1L<<4)
-#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5)
-#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6)
-#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7)
-#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8)
+#define PCI_CONFIG_2_BAR1_64ENA (1L<<4)
+#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5)
+#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6)
+#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7)
+#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_DISABLED (0L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_2K (1L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_4K (2L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_8M (13L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_16M (14L<<8)
#define PCI_CONFIG_2_EXP_ROM_SIZE_32M (15L<<8)
-#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16)
-#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17)
+#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16)
+#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17)
/* config_3 offset */
-#define GRC_CONFIG_3_SIZE_REG (0x40c)
-#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0)
-#define PCI_CONFIG_3_FORCE_PME (1L<<24)
-#define PCI_CONFIG_3_PME_STATUS (1L<<25)
-#define PCI_CONFIG_3_PME_ENABLE (1L<<26)
-#define PCI_CONFIG_3_PM_STATE (0x3L<<27)
-#define PCI_CONFIG_3_VAUX_PRESET (1L<<30)
-#define PCI_CONFIG_3_PCI_POWER (1L<<31)
-
-/* config_2 offset */
-#define GRC_CONFIG_2_SIZE_REG 0x408
+#define GRC_CONFIG_3_SIZE_REG 0x40c
+#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0)
+#define PCI_CONFIG_3_FORCE_PME (1L<<24)
+#define PCI_CONFIG_3_PME_STATUS (1L<<25)
+#define PCI_CONFIG_3_PME_ENABLE (1L<<26)
+#define PCI_CONFIG_3_PM_STATE (0x3L<<27)
+#define PCI_CONFIG_3_VAUX_PRESET (1L<<30)
+#define PCI_CONFIG_3_PCI_POWER (1L<<31)
#define GRC_BAR2_CONFIG 0x4e0
-#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0)
-#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0)
-#define PCI_CONFIG_2_BAR2_64ENA (1L<<4)
+#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0)
+#define PCI_CONFIG_2_BAR2_64ENA (1L<<4)
+
+#define PCI_PM_DATA_A 0x410
+#define PCI_PM_DATA_B 0x414
+#define PCI_ID_VAL1 0x434
+#define PCI_ID_VAL2 0x438
-#define PCI_PM_DATA_A (0x410)
-#define PCI_PM_DATA_B (0x414)
-#define PCI_ID_VAL1 (0x434)
-#define PCI_ID_VAL2 (0x438)
#define MDIO_REG_BANK_CL73_IEEEB0 0x0
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0
#define MDIO_PMA_REG_GEN_CTRL 0xca10
#define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188
#define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a
+#define MDIO_PMA_REG_M8051_MSGIN_REG 0xca12
+#define MDIO_PMA_REG_M8051_MSGOUT_REG 0xca13
#define MDIO_PMA_REG_ROM_VER1 0xca19
#define MDIO_PMA_REG_ROM_VER2 0xca1a
#define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b
#define MDIO_AN_REG_LINK_STATUS 0x8304
#define MDIO_AN_REG_CL37_CL73 0x8370
#define MDIO_AN_REG_CL37_AN 0xffe0
-#define MDIO_AN_REG_CL37_FD 0xffe4
+#define MDIO_AN_REG_CL37_FC_LD 0xffe4
+#define MDIO_AN_REG_CL37_FC_LP 0xffe5
#define IGU_FUNC_BASE 0x0400
#define IGU_INT_NOP 2
#define IGU_INT_NOP2 3
+#define COMMAND_REG_INT_ACK 0x0
+#define COMMAND_REG_PROD_UPD 0x4
+#define COMMAND_REG_ATTN_BITS_UPD 0x8
+#define COMMAND_REG_ATTN_BITS_SET 0xc
+#define COMMAND_REG_ATTN_BITS_CLR 0x10
+#define COMMAND_REG_COALESCE_NOW 0x14
+#define COMMAND_REG_SIMD_MASK 0x18
+#define COMMAND_REG_SIMD_NOMASK 0x1c
+