/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2007 Intel Corporation.
+ Copyright(c) 1999 - 2008 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
/* Cable length tables */
static const u16 e1000_m88_cable_length_table[] =
}
/**
- * e1000_read_phy_reg_mdic - Read MDI control register
+ * e1000e_read_phy_reg_mdic - Read MDI control register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
*
- * Reads the MDI control regsiter in the PHY at offset and stores the
+ * Reads the MDI control register in the PHY at offset and stores the
* information read to data.
**/
-static s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
{
struct e1000_phy_info *phy = &hw->phy;
u32 i, mdic = 0;
return -E1000_ERR_PARAM;
}
- /* Set up Op-code, Phy Address, and register offset in the MDI
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
* Control register. The MAC will take care of interfacing with the
* PHY to retrieve the desired data.
*/
ew32(MDIC, mdic);
- /* Poll the ready bit to see if the MDI read completed */
- for (i = 0; i < 64; i++) {
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
udelay(50);
mdic = er32(MDIC);
if (mdic & E1000_MDIC_READY)
}
/**
- * e1000_write_phy_reg_mdic - Write MDI control register
+ * e1000e_write_phy_reg_mdic - Write MDI control register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write to register at offset
*
* Writes data to MDI control register in the PHY at offset.
**/
-static s32 e1000_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
{
struct e1000_phy_info *phy = &hw->phy;
u32 i, mdic = 0;
return -E1000_ERR_PARAM;
}
- /* Set up Op-code, Phy Address, and register offset in the MDI
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
* Control register. The MAC will take care of interfacing with the
* PHY to retrieve the desired data.
*/
ew32(MDIC, mdic);
- /* Poll the ready bit to see if the MDI read completed */
- for (i = 0; i < E1000_GEN_POLL_TIMEOUT; i++) {
- udelay(5);
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+ udelay(50);
mdic = er32(MDIC);
if (mdic & E1000_MDIC_READY)
break;
hw_dbg(hw, "MDI Write did not complete\n");
return -E1000_ERR_PHY;
}
+ if (mdic & E1000_MDIC_ERROR) {
+ hw_dbg(hw, "MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
return 0;
}
if (ret_val)
return ret_val;
- ret_val = e1000_read_phy_reg_mdic(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
hw->phy.ops.release_phy(hw);
if (ret_val)
return ret_val;
- ret_val = e1000_write_phy_reg_mdic(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
hw->phy.ops.release_phy(hw);
return ret_val;
if (offset > MAX_PHY_MULTI_PAGE_REG) {
- ret_val = e1000_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (u16)offset);
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
if (ret_val) {
hw->phy.ops.release_phy(hw);
return ret_val;
}
}
- ret_val = e1000_read_phy_reg_mdic(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
hw->phy.ops.release_phy(hw);
return ret_val;
if (offset > MAX_PHY_MULTI_PAGE_REG) {
- ret_val = e1000_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (u16)offset);
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
if (ret_val) {
hw->phy.ops.release_phy(hw);
return ret_val;
}
}
- ret_val = e1000_write_phy_reg_mdic(hw,
- MAX_PHY_REG_ADDRESS & offset,
- data);
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
hw->phy.ops.release_phy(hw);
s32 ret_val;
u16 phy_data;
- /* Enable CRS on TX. This must be set for half-duplex operation. */
+ /* Enable CRS on Tx. This must be set for half-duplex operation. */
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
if (ret_val)
return ret_val;
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ /* For newer PHYs this bit is downshift enable */
+ if (phy->type == e1000_phy_m88)
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- /* Options:
+ /*
+ * Options:
* MDI/MDI-X = 0 (default)
* 0 - Auto for all speeds
* 1 - MDI mode
break;
}
- /* Options:
+ /*
+ * Options:
* disable_polarity_correction = 0 (default)
* Automatic Correction for Reversed Cable Polarity
* 0 - Disabled
if (phy->disable_polarity_correction == 1)
phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ /* Enable downshift on BM (disabled by default) */
+ if (phy->type == e1000_phy_bm)
+ phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT;
+
ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
if (ret_val)
return ret_val;
- if (phy->revision < 4) {
- /* Force TX_CLK in the Extended PHY Specific Control Register
+ if ((phy->type == e1000_phy_m88) && (phy->revision < 4)) {
+ /*
+ * Force TX_CLK in the Extended PHY Specific Control Register
* to 25MHz clock.
*/
ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
return ret_val;
}
- /* Wait 15ms for MAC to configure PHY from NVM settings. */
- msleep(15);
+ /*
+ * Wait 100ms for MAC to configure PHY from NVM settings, to avoid
+ * timeout issues when LFS is enabled.
+ */
+ msleep(100);
/* disable lplu d0 during driver init */
ret_val = e1000_set_d0_lplu_state(hw, 0);
/* set auto-master slave resolution settings */
if (hw->mac.autoneg) {
- /* when autonegotiation advertisement is only 1000Mbps then we
+ /*
+ * when autonegotiation advertisement is only 1000Mbps then we
* should disable SmartSpeed and enable Auto MasterSlave
- * resolution as hardware default. */
+ * resolution as hardware default.
+ */
if (phy->autoneg_advertised == ADVERTISE_1000_FULL) {
/* Disable SmartSpeed */
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- &data);
+ &data);
if (ret_val)
return ret_val;
data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- data);
+ data);
if (ret_val)
return ret_val;
return ret_val;
}
- /* Need to parse both autoneg_advertised and fc and set up
+ /*
+ * Need to parse both autoneg_advertised and fc and set up
* the appropriate PHY registers. First we will parse for
* autoneg_advertised software override. Since we can advertise
* a plethora of combinations, we need to check each bit
* individually.
*/
- /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ /*
+ * First we clear all the 10/100 mb speed bits in the Auto-Neg
* Advertisement Register (Address 4) and the 1000 mb speed bits in
* the 1000Base-T Control Register (Address 9).
*/
mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
}
- /* Check for a software override of the flow control settings, and
+ /*
+ * Check for a software override of the flow control settings, and
* setup the PHY advertisement registers accordingly. If
* auto-negotiation is enabled, then software will have to set the
* "PAUSE" bits to the correct value in the Auto-Negotiation
* but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames
* but we do not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: No software override. The flow control configuration
* in the EEPROM is used.
*/
- switch (hw->mac.fc) {
+ switch (hw->fc.type) {
case e1000_fc_none:
- /* Flow control (RX & TX) is completely disabled by a
+ /*
+ * Flow control (Rx & Tx) is completely disabled by a
* software over-ride.
*/
mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
case e1000_fc_rx_pause:
- /* RX Flow control is enabled, and TX Flow control is
+ /*
+ * Rx Flow control is enabled, and Tx Flow control is
* disabled, by a software over-ride.
- */
- /* Since there really isn't a way to advertise that we are
- * capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later
+ *
+ * Since there really isn't a way to advertise that we are
+ * capable of Rx Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric Rx PAUSE. Later
* (in e1000e_config_fc_after_link_up) we will disable the
* hw's ability to send PAUSE frames.
*/
mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
case e1000_fc_tx_pause:
- /* TX Flow control is enabled, and RX Flow control is
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
* disabled, by a software over-ride.
*/
mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
break;
case e1000_fc_full:
- /* Flow control (both RX and TX) is enabled by a software
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
* over-ride.
*/
mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
* Performs initial bounds checking on autoneg advertisement parameter, then
* configure to advertise the full capability. Setup the PHY to autoneg
* and restart the negotiation process between the link partner. If
- * wait_for_link, then wait for autoneg to complete before exiting.
+ * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
**/
static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
{
s32 ret_val;
u16 phy_ctrl;
- /* Perform some bounds checking on the autoneg advertisement
+ /*
+ * Perform some bounds checking on the autoneg advertisement
* parameter.
*/
phy->autoneg_advertised &= phy->autoneg_mask;
- /* If autoneg_advertised is zero, we assume it was not defaulted
+ /*
+ * If autoneg_advertised is zero, we assume it was not defaulted
* by the calling code so we set to advertise full capability.
*/
if (phy->autoneg_advertised == 0)
}
hw_dbg(hw, "Restarting Auto-Neg\n");
- /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ /*
+ * Restart auto-negotiation by setting the Auto Neg Enable bit and
* the Auto Neg Restart bit in the PHY control register.
*/
ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
if (ret_val)
return ret_val;
- /* Does the user want to wait for Auto-Neg to complete here, or
+ /*
+ * Does the user want to wait for Auto-Neg to complete here, or
* check at a later time (for example, callback routine).
*/
- if (phy->wait_for_link) {
+ if (phy->autoneg_wait_to_complete) {
ret_val = e1000_wait_autoneg(hw);
if (ret_val) {
hw_dbg(hw, "Error while waiting for "
bool link;
if (hw->mac.autoneg) {
- /* Setup autoneg and flow control advertisement and perform
- * autonegotiation. */
+ /*
+ * Setup autoneg and flow control advertisement and perform
+ * autonegotiation.
+ */
ret_val = e1000_copper_link_autoneg(hw);
if (ret_val)
return ret_val;
} else {
- /* PHY will be set to 10H, 10F, 100H or 100F
- * depending on user settings. */
+ /*
+ * PHY will be set to 10H, 10F, 100H or 100F
+ * depending on user settings.
+ */
hw_dbg(hw, "Forcing Speed and Duplex\n");
ret_val = e1000_phy_force_speed_duplex(hw);
if (ret_val) {
}
}
- /* Check link status. Wait up to 100 microseconds for link to become
+ /*
+ * Check link status. Wait up to 100 microseconds for link to become
* valid.
*/
ret_val = e1000e_phy_has_link_generic(hw,
if (ret_val)
return ret_val;
- /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ /*
+ * Clear Auto-Crossover to force MDI manually. IGP requires MDI
* forced whenever speed and duplex are forced.
*/
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
udelay(1);
- if (phy->wait_for_link) {
+ if (phy->autoneg_wait_to_complete) {
hw_dbg(hw, "Waiting for forced speed/duplex link on IGP phy.\n");
ret_val = e1000e_phy_has_link_generic(hw,
* Calls the PHY setup function to force speed and duplex. Clears the
* auto-crossover to force MDI manually. Resets the PHY to commit the
* changes. If time expires while waiting for link up, we reset the DSP.
- * After reset, TX_CLK and CRS on TX must be set. Return successful upon
+ * After reset, TX_CLK and CRS on Tx must be set. Return successful upon
* successful completion, else return corresponding error code.
**/
s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
u16 phy_data;
bool link;
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
* forced whenever speed and duplex are forced.
*/
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
udelay(1);
- if (phy->wait_for_link) {
+ if (phy->autoneg_wait_to_complete) {
hw_dbg(hw, "Waiting for forced speed/duplex link on M88 phy.\n");
ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
return ret_val;
if (!link) {
- /* We didn't get link.
+ /*
+ * We didn't get link.
* Reset the DSP and cross our fingers.
*/
- ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT, 0x001d);
+ ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT,
+ 0x001d);
if (ret_val)
return ret_val;
ret_val = e1000e_phy_reset_dsp(hw);
if (ret_val)
return ret_val;
- /* Resetting the phy means we need to re-force TX_CLK in the
+ /*
+ * Resetting the phy means we need to re-force TX_CLK in the
* Extended PHY Specific Control Register to 25MHz clock from
* the reset value of 2.5MHz.
*/
if (ret_val)
return ret_val;
- /* In addition, we must re-enable CRS on Tx for both half and full
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
* duplex.
*/
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
u32 ctrl;
/* Turn off flow control when forcing speed/duplex */
- mac->fc = e1000_fc_none;
+ hw->fc.type = e1000_fc_none;
/* Force speed/duplex on the mac */
ctrl = er32(CTRL);
if (!active) {
data &= ~IGP02E1000_PM_D3_LPLU;
- ret_val = e1e_wphy(hw,
- IGP02E1000_PHY_POWER_MGMT,
- data);
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
if (ret_val)
return ret_val;
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
* during Dx states where the power conservation is most
* important. During driver activity we should enable
- * SmartSpeed, so performance is maintained. */
+ * SmartSpeed, so performance is maintained.
+ */
if (phy->smart_speed == e1000_smart_speed_on) {
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- &data);
+ &data);
if (ret_val)
return ret_val;
data |= IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- data);
+ data);
if (ret_val)
return ret_val;
} else if (phy->smart_speed == e1000_smart_speed_off) {
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- &data);
+ &data);
if (ret_val)
return ret_val;
data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
- data);
+ data);
if (ret_val)
return ret_val;
}
}
/**
- * e1000e_check_downshift - Checks whether a downshift in speed occured
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
* @hw: pointer to the HW structure
*
* Success returns 0, Failure returns 1
s32 ret_val;
u16 data, offset, mask;
- /* Polarity is determined based on the speed of
- * our connection. */
+ /*
+ * Polarity is determined based on the speed of
+ * our connection.
+ */
ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_STATUS, &data);
if (ret_val)
return ret_val;
offset = IGP01E1000_PHY_PCS_INIT_REG;
mask = IGP01E1000_PHY_POLARITY_MASK;
} else {
- /* This really only applies to 10Mbps since
+ /*
+ * This really only applies to 10Mbps since
* there is no polarity for 100Mbps (always 0).
*/
offset = IGP01E1000_PHY_PORT_STATUS;
}
/**
- * e1000_wait_autoneg - Wait for auto-neg compeletion
+ * e1000_wait_autoneg - Wait for auto-neg completion
* @hw: pointer to the HW structure
*
* Waits for auto-negotiation to complete or for the auto-negotiation time
msleep(100);
}
- /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
+ /*
+ * PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
* has completed.
*/
return ret_val;
u16 i, phy_status;
for (i = 0; i < iterations; i++) {
- /* Some PHYs require the PHY_STATUS register to be read
+ /*
+ * Some PHYs require the PHY_STATUS register to be read
* twice due to the link bit being sticky. No harm doing
* it across the board.
*/
*
* The automatic gain control (agc) normalizes the amplitude of the
* received signal, adjusting for the attenuation produced by the
- * cable. By reading the AGC registers, which reperesent the
- * cobination of course and fine gain value, the value can be put
+ * cable. By reading the AGC registers, which represent the
+ * combination of course and fine gain value, the value can be put
* into a lookup table to obtain the approximate cable length
* for each channel.
**/
if (ret_val)
return ret_val;
- /* Getting bits 15:9, which represent the combination of
+ /*
+ * Getting bits 15:9, which represent the combination of
* course and fine gain values. The result is a number
* that can be put into the lookup table to obtain the
- * approximate cable length. */
+ * approximate cable length.
+ */
cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
IGP02E1000_AGC_LENGTH_MASK;
u16 phy_data;
bool link;
- if (hw->media_type != e1000_media_type_copper) {
+ if (hw->phy.media_type != e1000_media_type_copper) {
hw_dbg(hw, "Phy info is only valid for copper media\n");
return -E1000_ERR_CONFIG;
}
* Verify the reset block is not blocking us from resetting. Acquire
* semaphore (if necessary) and read/set/write the device control reset
* bit in the PHY. Wait the appropriate delay time for the device to
- * reset and relase the semaphore (if necessary).
+ * reset and release the semaphore (if necessary).
**/
s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
{
case IFE_C_E_PHY_ID:
phy_type = e1000_phy_ife;
break;
+ case BME1000_E_PHY_ID:
+ case BME1000_E_PHY_ID_R2:
+ phy_type = e1000_phy_bm;
+ break;
default:
phy_type = e1000_phy_unknown;
break;
return phy_type;
}
+/**
+ * e1000e_determine_phy_address - Determines PHY address.
+ * @hw: pointer to the HW structure
+ *
+ * This uses a trial and error method to loop through possible PHY
+ * addresses. It tests each by reading the PHY ID registers and
+ * checking for a match.
+ **/
+s32 e1000e_determine_phy_address(struct e1000_hw *hw)
+{
+ s32 ret_val = -E1000_ERR_PHY_TYPE;
+ u32 phy_addr= 0;
+ u32 i = 0;
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
+
+ do {
+ for (phy_addr = 0; phy_addr < 4; phy_addr++) {
+ hw->phy.addr = phy_addr;
+ e1000e_get_phy_id(hw);
+ phy_type = e1000e_get_phy_type_from_id(hw->phy.id);
+
+ /*
+ * If phy_type is valid, break - we found our
+ * PHY address
+ */
+ if (phy_type != e1000_phy_unknown) {
+ ret_val = 0;
+ break;
+ }
+ }
+ i++;
+ } while ((ret_val != 0) && (i < 100));
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address
+ * @page: page to access
+ *
+ * Returns the phy address for the page requested.
+ **/
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg)
+{
+ u32 phy_addr = 2;
+
+ if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31))
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000e_write_phy_reg_bm - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+ hw->phy.ops.release_phy(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to read or write
+ * @read: determines if operation is read or write
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting. Note that procedure to read the wakeup
+ * registers are different. It works as such:
+ * 1) Set page 769, register 17, bit 2 = 1
+ * 2) Set page to 800 for host (801 if we were manageability)
+ * 3) Write the address using the address opcode (0x11)
+ * 4) Read or write the data using the data opcode (0x12)
+ * 5) Restore 769_17.2 to its original value
+ **/
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u16 reg = ((u16)offset) & PHY_REG_MASK;
+ u16 phy_reg = 0;
+ u8 phy_acquired = 1;
+
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val) {
+ phy_acquired = 0;
+ goto out;
+ }
+
+ /* All operations in this function are phy address 1 */
+ hw->phy.addr = 1;
+
+ /* Set page 769 */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (ret_val)
+ goto out;
+
+ /* First clear bit 4 to avoid a power state change */
+ phy_reg &= ~(BM_WUC_HOST_WU_BIT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val)
+ goto out;
+
+ /* Write bit 2 = 1, and clear bit 4 to 769_17 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG,
+ phy_reg | BM_WUC_ENABLE_BIT);
+ if (ret_val)
+ goto out;
+
+ /* Select page 800 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+
+ /* Write the page 800 offset value using opcode 0x11 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg);
+ if (ret_val)
+ goto out;
+
+ if (read) {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ data);
+ } else {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ *data);
+ }
+
+ if (ret_val)
+ goto out;
+
+ /*
+ * Restore 769_17.2 to its original value
+ * Set page 769
+ */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ /* Clear 769_17.2 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+
+out:
+ if (phy_acquired == 1)
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
/**
* e1000e_commit_phy - Soft PHY reset
* @hw: pointer to the HW structure