/*******************************************************************************
Intel(R) Gigabit Ethernet Linux driver
- Copyright(c) 2007 Intel Corporation.
+ Copyright(c) 2007 - 2008 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
#define E1000_I2CCMD_ERROR 0x80000000
#define E1000_MAX_SGMII_PHY_REG_ADDR 255
#define E1000_I2CCMD_PHY_TIMEOUT 200
+#define E1000_IVAR_VALID 0x80
+#define E1000_GPIE_NSICR 0x00000001
+#define E1000_GPIE_MSIX_MODE 0x00000010
+#define E1000_GPIE_EIAME 0x40000000
+#define E1000_GPIE_PBA 0x80000000
-/* Receive Decriptor bit definitions */
+/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
-#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
/* Device Control */
#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
*/
#define E1000_CONNSW_ENRGSRC 0x4
+#define E1000_PCS_CFG_PCS_EN 8
#define E1000_PCS_LCTL_FLV_LINK_UP 1
#define E1000_PCS_LCTL_FSV_100 2
#define E1000_PCS_LCTL_FSV_1000 4
#define E1000_PCS_LCTL_FDV_FULL 8
#define E1000_PCS_LCTL_FSD 0x10
#define E1000_PCS_LCTL_FORCE_LINK 0x20
+#define E1000_PCS_LCTL_FORCE_FCTRL 0x80
#define E1000_PCS_LCTL_AN_ENABLE 0x10000
#define E1000_PCS_LCTL_AN_RESTART 0x20000
#define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
+#define E1000_ENABLE_SERDES_LOOPBACK 0x0410
#define E1000_PCS_LSTS_LINK_OK 1
#define E1000_PCS_LSTS_SPEED_100 2
#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
/* Header split receive */
+#define E1000_RFCTL_LEF 0x00040000
/* Collision related configuration parameters */
#define E1000_COLLISION_THRESHOLD 15
#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
#define E1000_PBA_24K 0x0018
#define E1000_PBA_34K 0x0022
+#define E1000_PBA_64K 0x0040 /* 64KB */
#define IFS_MAX 80
#define IFS_MIN 40
#define E1000_ICR_RXO 0x00000040 /* rx overrun */
#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
-#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
+#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */
#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-/* queue 0 Rx descriptor FIFO parity error */
-/* queue 0 Tx descriptor FIFO parity error */
-/* host arb read buffer parity error */
-/* packet buffer parity error */
-/* queue 1 Rx descriptor FIFO parity error */
-/* queue 1 Tx descriptor FIFO parity error */
/* Extended Interrupt Mask Set */
#define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */
/* Interrupt Cause Set */
#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-/* queue 0 Rx descriptor FIFO parity error */
-/* queue 0 Tx descriptor FIFO parity error */
-/* host arb read buffer parity error */
-/* packet buffer parity error */
-/* queue 1 Rx descriptor FIFO parity error */
-/* queue 1 Tx descriptor FIFO parity error */
/* Extended Interrupt Cause Set */
/* PHY Control Register */
#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
/* 1000BASE-T Control Register */
#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
- /* 0=DTE device */
#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
/* 0=Configure PHY as Slave */
#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CONTROL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Regiser */
+#define PHY_STATUS 0x01 /* Status Register */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
/* Auto crossover enabled all speeds */
#define M88E1000_PSCR_AUTO_X_MODE 0x0060
/*
- * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T RX Threshold
- * 0=Normal 10BASE-T RX Threshold
+ * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold
+ * 0=Normal 10BASE-T Rx Threshold
*/
/* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
projects / linux-2.6-omap-h63xx.git / blobdiff