*
*/
#include <linux/kernel.h>
-#include <linux/sched.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/unistd.h>
#define MII_M1011_IMASK_INIT 0x6400
#define MII_M1011_IMASK_CLEAR 0x0000
+#define MII_M1011_PHY_SCR 0x10
+#define MII_M1011_PHY_SCR_AUTO_CROSS 0x0060
+
+#define MII_M1145_PHY_EXT_CR 0x14
+#define MII_M1145_RGMII_RX_DELAY 0x0080
+#define MII_M1145_RGMII_TX_DELAY 0x0002
+
+#define M1145_DEV_FLAGS_RESISTANCE 0x00000001
+
+#define MII_M1111_PHY_LED_CONTROL 0x18
+#define MII_M1111_PHY_LED_DIRECT 0x4100
+#define MII_M1111_PHY_LED_COMBINE 0x411c
+#define MII_M1111_PHY_EXT_CR 0x14
+#define MII_M1111_RX_DELAY 0x80
+#define MII_M1111_TX_DELAY 0x2
+#define MII_M1111_PHY_EXT_SR 0x1b
+
+#define MII_M1111_HWCFG_MODE_MASK 0xf
+#define MII_M1111_HWCFG_MODE_COPPER_RGMII 0xb
+#define MII_M1111_HWCFG_MODE_FIBER_RGMII 0x3
+#define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4
+#define MII_M1111_HWCFG_FIBER_COPPER_AUTO 0x8000
+#define MII_M1111_HWCFG_FIBER_COPPER_RES 0x2000
+
+#define MII_M1111_COPPER 0
+#define MII_M1111_FIBER 1
+
+#define MII_M1011_PHY_STATUS 0x11
+#define MII_M1011_PHY_STATUS_1000 0x8000
+#define MII_M1011_PHY_STATUS_100 0x4000
+#define MII_M1011_PHY_STATUS_SPD_MASK 0xc000
+#define MII_M1011_PHY_STATUS_FULLDUPLEX 0x2000
+#define MII_M1011_PHY_STATUS_RESOLVED 0x0800
+#define MII_M1011_PHY_STATUS_LINK 0x0400
+
+
MODULE_DESCRIPTION("Marvell PHY driver");
MODULE_AUTHOR("Andy Fleming");
MODULE_LICENSE("GPL");
{
int err;
- if(phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
else
err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
if (err < 0)
return err;
+ err = phy_write(phydev, MII_M1011_PHY_SCR,
+ MII_M1011_PHY_SCR_AUTO_CROSS);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, MII_M1111_PHY_LED_CONTROL,
+ MII_M1111_PHY_LED_DIRECT);
+ if (err < 0)
+ return err;
err = genphy_config_aneg(phydev);
return err;
}
+static int m88e1111_config_init(struct phy_device *phydev)
+{
+ int err;
+ int temp;
+ int mode;
+
+ /* Enable Fiber/Copper auto selection */
+ temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
+ temp |= MII_M1111_HWCFG_FIBER_COPPER_AUTO;
+ phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
+
+ temp = phy_read(phydev, MII_BMCR);
+ temp |= BMCR_RESET;
+ phy_write(phydev, MII_BMCR, temp);
+
+ if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+ (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
+ (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
+ (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
+
+ temp = phy_read(phydev, MII_M1111_PHY_EXT_CR);
+ if (temp < 0)
+ return temp;
+
+ if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
+ temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY);
+ } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+ temp &= ~MII_M1111_TX_DELAY;
+ temp |= MII_M1111_RX_DELAY;
+ } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+ temp &= ~MII_M1111_RX_DELAY;
+ temp |= MII_M1111_TX_DELAY;
+ }
+
+ err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp);
+ if (err < 0)
+ return err;
+
+ temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
+ if (temp < 0)
+ return temp;
+
+ temp &= ~(MII_M1111_HWCFG_MODE_MASK);
+
+ mode = phy_read(phydev, MII_M1111_PHY_EXT_CR);
+
+ if (mode & MII_M1111_HWCFG_FIBER_COPPER_RES)
+ temp |= MII_M1111_HWCFG_MODE_FIBER_RGMII;
+ else
+ temp |= MII_M1111_HWCFG_MODE_COPPER_RGMII;
+
+ err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
+ if (err < 0)
+ return err;
+ }
+
+ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+ temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
+ if (temp < 0)
+ return temp;
+
+ temp &= ~(MII_M1111_HWCFG_MODE_MASK);
+ temp |= MII_M1111_HWCFG_MODE_SGMII_NO_CLK;
+
+ err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
+ if (err < 0)
+ return err;
+ }
+
+ err = phy_write(phydev, MII_BMCR, BMCR_RESET);
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int m88e1145_config_init(struct phy_device *phydev)
+{
+ int err;
+
+ /* Take care of errata E0 & E1 */
+ err = phy_write(phydev, 0x1d, 0x001b);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0x418f);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1d, 0x0016);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0xa2da);
+ if (err < 0)
+ return err;
+
+ if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
+ int temp = phy_read(phydev, MII_M1145_PHY_EXT_CR);
+ if (temp < 0)
+ return temp;
+
+ temp |= (MII_M1145_RGMII_RX_DELAY | MII_M1145_RGMII_TX_DELAY);
+
+ err = phy_write(phydev, MII_M1145_PHY_EXT_CR, temp);
+ if (err < 0)
+ return err;
+
+ if (phydev->dev_flags & M1145_DEV_FLAGS_RESISTANCE) {
+ err = phy_write(phydev, 0x1d, 0x0012);
+ if (err < 0)
+ return err;
+
+ temp = phy_read(phydev, 0x1e);
+ if (temp < 0)
+ return temp;
+
+ temp &= 0xf03f;
+ temp |= 2 << 9; /* 36 ohm */
+ temp |= 2 << 6; /* 39 ohm */
+
+ err = phy_write(phydev, 0x1e, temp);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1d, 0x3);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0x8000);
+ if (err < 0)
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+/* marvell_read_status
+ *
+ * Generic status code does not detect Fiber correctly!
+ * Description:
+ * Check the link, then figure out the current state
+ * by comparing what we advertise with what the link partner
+ * advertises. Start by checking the gigabit possibilities,
+ * then move on to 10/100.
+ */
+static int marvell_read_status(struct phy_device *phydev)
+{
+ int adv;
+ int err;
+ int lpa;
+ int status = 0;
+
+ /* Update the link, but return if there
+ * was an error */
+ err = genphy_update_link(phydev);
+ if (err)
+ return err;
+
+ if (AUTONEG_ENABLE == phydev->autoneg) {
+ status = phy_read(phydev, MII_M1011_PHY_STATUS);
+ if (status < 0)
+ return status;
+
+ lpa = phy_read(phydev, MII_LPA);
+ if (lpa < 0)
+ return lpa;
+
+ adv = phy_read(phydev, MII_ADVERTISE);
+ if (adv < 0)
+ return adv;
+
+ lpa &= adv;
+
+ if (status & MII_M1011_PHY_STATUS_FULLDUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ status = status & MII_M1011_PHY_STATUS_SPD_MASK;
+ phydev->pause = phydev->asym_pause = 0;
+
+ switch (status) {
+ case MII_M1011_PHY_STATUS_1000:
+ phydev->speed = SPEED_1000;
+ break;
+
+ case MII_M1011_PHY_STATUS_100:
+ phydev->speed = SPEED_100;
+ break;
+
+ default:
+ phydev->speed = SPEED_10;
+ break;
+ }
+
+ if (phydev->duplex == DUPLEX_FULL) {
+ phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
+ phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
+ }
+ } else {
+ int bmcr = phy_read(phydev, MII_BMCR);
+
+ if (bmcr < 0)
+ return bmcr;
-static struct phy_driver m88e1101_driver = {
- .phy_id = 0x01410c00,
- .phy_id_mask = 0xffffff00,
- .name = "Marvell 88E1101",
- .features = PHY_GBIT_FEATURES,
- .flags = PHY_HAS_INTERRUPT,
- .config_aneg = &marvell_config_aneg,
- .read_status = &genphy_read_status,
- .ack_interrupt = &marvell_ack_interrupt,
- .config_intr = &marvell_config_intr,
- .driver = { .owner = THIS_MODULE,},
+ if (bmcr & BMCR_FULLDPLX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (bmcr & BMCR_SPEED1000)
+ phydev->speed = SPEED_1000;
+ else if (bmcr & BMCR_SPEED100)
+ phydev->speed = SPEED_100;
+ else
+ phydev->speed = SPEED_10;
+
+ phydev->pause = phydev->asym_pause = 0;
+ }
+
+ return 0;
+}
+
+static struct phy_driver marvell_drivers[] = {
+ {
+ .phy_id = 0x01410c60,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1101",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE },
+ },
+ {
+ .phy_id = 0x01410c90,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1112",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = &m88e1111_config_init,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE },
+ },
+ {
+ .phy_id = 0x01410cc0,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1111",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = &m88e1111_config_init,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &marvell_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE },
+ },
+ {
+ .phy_id = 0x01410cd0,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1145",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = &m88e1145_config_init,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE },
+ },
+ {
+ .phy_id = 0x01410e30,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1240",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = &m88e1111_config_init,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE },
+ },
};
static int __init marvell_init(void)
{
- return phy_driver_register(&m88e1101_driver);
+ int ret;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(marvell_drivers); i++) {
+ ret = phy_driver_register(&marvell_drivers[i]);
+
+ if (ret) {
+ while (i-- > 0)
+ phy_driver_unregister(&marvell_drivers[i]);
+ return ret;
+ }
+ }
+
+ return 0;
}
static void __exit marvell_exit(void)
{
- phy_driver_unregister(&m88e1101_driver);
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(marvell_drivers); i++)
+ phy_driver_unregister(&marvell_drivers[i]);
}
module_init(marvell_init);
projects / linux-2.6-omap-h63xx.git / blobdiff