#define C22EXT_STATUS_LINK_LBN 2
#define C22EXT_STATUS_LINK_WIDTH 1
-#define C22EXT_MSTSLV_REG 49162
-#define C22EXT_MSTSLV_1000_HD_LBN 10
-#define C22EXT_MSTSLV_1000_HD_WIDTH 1
-#define C22EXT_MSTSLV_1000_FD_LBN 11
-#define C22EXT_MSTSLV_1000_FD_WIDTH 1
+#define C22EXT_MSTSLV_CTRL 49161
+#define C22EXT_MSTSLV_CTRL_ADV_1000_HD_LBN 8
+#define C22EXT_MSTSLV_CTRL_ADV_1000_FD_LBN 9
+
+#define C22EXT_MSTSLV_STATUS 49162
+#define C22EXT_MSTSLV_STATUS_LP_1000_HD_LBN 10
+#define C22EXT_MSTSLV_STATUS_LP_1000_FD_LBN 11
/* Time to wait between powering down the LNPGA and turning off the power
* rails */
rc = tenxpress_init(efx);
if (rc < 0)
goto fail;
+ mdio_clause45_set_pause(efx);
if (efx->phy_type == PHY_TYPE_SFT9001B) {
rc = device_create_file(&efx->pci_dev->dev,
/* The XGMAC clock is driven from the SFC7101/SFT9001 312MHz clock, so
* a special software reset can glitch the XGMAC sufficiently for stats
- * requests to fail. Since we don't often special_reset, just lock. */
- spin_lock(&efx->stats_lock);
+ * requests to fail. */
+ efx_stats_disable(efx);
/* Initiate reset */
reg = mdio_clause45_read(efx, efx->mii.phy_id,
rc = mdio_clause45_wait_reset_mmds(efx,
TENXPRESS_REQUIRED_DEVS);
if (rc < 0)
- goto unlock;
+ goto out;
/* Try and reconfigure the device */
rc = tenxpress_init(efx);
if (rc < 0)
- goto unlock;
+ goto out;
/* Wait for the XGXS state machine to churn */
mdelay(10);
-unlock:
- spin_unlock(&efx->stats_lock);
+out:
+ efx_stats_enable(efx);
return rc;
}
{
struct tenxpress_phy_data *phy_data = efx->phy_data;
struct ethtool_cmd ecmd;
- bool phy_mode_change, loop_reset, loop_toggle, loopback;
+ bool phy_mode_change, loop_reset;
if (efx->phy_mode & (PHY_MODE_OFF | PHY_MODE_SPECIAL)) {
phy_data->phy_mode = efx->phy_mode;
phy_mode_change = (efx->phy_mode == PHY_MODE_NORMAL &&
phy_data->phy_mode != PHY_MODE_NORMAL);
- loopback = LOOPBACK_MASK(efx) & efx->phy_op->loopbacks;
- loop_toggle = LOOPBACK_CHANGED(phy_data, efx, efx->phy_op->loopbacks);
loop_reset = (LOOPBACK_OUT_OF(phy_data, efx, efx->phy_op->loopbacks) ||
LOOPBACK_CHANGED(phy_data, efx, 1 << LOOPBACK_GPHY));
- if (loop_reset || loop_toggle || loopback || phy_mode_change) {
+ if (loop_reset || phy_mode_change) {
int rc;
efx->phy_op->get_settings(efx, &ecmd);
falcon_reset_xaui(efx);
}
- if (efx->phy_type != PHY_TYPE_SFX7101) {
- /* Only change autoneg once, on coming out or
- * going into loopback */
- if (loop_toggle)
- ecmd.autoneg = !loopback;
- if (loopback) {
- ecmd.duplex = DUPLEX_FULL;
- if (efx->loopback_mode == LOOPBACK_GPHY)
- ecmd.speed = SPEED_1000;
- else
- ecmd.speed = SPEED_10000;
- }
- }
-
rc = efx->phy_op->set_settings(efx, &ecmd);
WARN_ON(rc);
}
return rc;
}
-static u32 tenxpress_get_xnp_lpa(struct efx_nic *efx)
+static void
+tenxpress_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
{
- int phy = efx->mii.phy_id;
- u32 lpa = 0;
+ int phy_id = efx->mii.phy_id;
+ u32 adv = 0, lpa = 0;
int reg;
if (efx->phy_type != PHY_TYPE_SFX7101) {
- reg = mdio_clause45_read(efx, phy, MDIO_MMD_C22EXT,
- C22EXT_MSTSLV_REG);
- if (reg & (1 << C22EXT_MSTSLV_1000_HD_LBN))
+ reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_C22EXT,
+ C22EXT_MSTSLV_CTRL);
+ if (reg & (1 << C22EXT_MSTSLV_CTRL_ADV_1000_FD_LBN))
+ adv |= ADVERTISED_1000baseT_Full;
+ reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_C22EXT,
+ C22EXT_MSTSLV_STATUS);
+ if (reg & (1 << C22EXT_MSTSLV_STATUS_LP_1000_HD_LBN))
lpa |= ADVERTISED_1000baseT_Half;
- if (reg & (1 << C22EXT_MSTSLV_1000_FD_LBN))
+ if (reg & (1 << C22EXT_MSTSLV_STATUS_LP_1000_FD_LBN))
lpa |= ADVERTISED_1000baseT_Full;
}
- reg = mdio_clause45_read(efx, phy, MDIO_MMD_AN, MDIO_AN_10GBT_STATUS);
+ reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_AN,
+ MDIO_AN_10GBT_CTRL);
+ if (reg & (1 << MDIO_AN_10GBT_CTRL_ADV_10G_LBN))
+ adv |= ADVERTISED_10000baseT_Full;
+ reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_AN,
+ MDIO_AN_10GBT_STATUS);
if (reg & (1 << MDIO_AN_10GBT_STATUS_LP_10G_LBN))
lpa |= ADVERTISED_10000baseT_Full;
- return lpa;
-}
-static void sfx7101_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
-{
- mdio_clause45_get_settings_ext(efx, ecmd, ADVERTISED_10000baseT_Full,
- tenxpress_get_xnp_lpa(efx));
- ecmd->supported |= SUPPORTED_10000baseT_Full;
- ecmd->advertising |= ADVERTISED_10000baseT_Full;
+ mdio_clause45_get_settings_ext(efx, ecmd, adv, lpa);
+
+ if (efx->phy_type != PHY_TYPE_SFX7101)
+ ecmd->supported |= (SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full);
+
+ /* In loopback, the PHY automatically brings up the correct interface,
+ * but doesn't advertise the correct speed. So override it */
+ if (efx->loopback_mode == LOOPBACK_GPHY)
+ ecmd->speed = SPEED_1000;
+ else if (LOOPBACK_MASK(efx) & efx->phy_op->loopbacks)
+ ecmd->speed = SPEED_10000;
}
-static void sft9001_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
+static int tenxpress_set_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
{
- int phy_id = efx->mii.phy_id;
- u32 xnp_adv = 0;
- int reg;
-
- reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_PMAPMD,
- PMA_PMD_SPEED_ENABLE_REG);
- if (EFX_WORKAROUND_13204(efx) && (reg & (1 << PMA_PMD_100TX_ADV_LBN)))
- xnp_adv |= ADVERTISED_100baseT_Full;
- if (reg & (1 << PMA_PMD_1000T_ADV_LBN))
- xnp_adv |= ADVERTISED_1000baseT_Full;
- if (reg & (1 << PMA_PMD_10000T_ADV_LBN))
- xnp_adv |= ADVERTISED_10000baseT_Full;
-
- mdio_clause45_get_settings_ext(efx, ecmd, xnp_adv,
- tenxpress_get_xnp_lpa(efx));
+ if (!ecmd->autoneg)
+ return -EINVAL;
- ecmd->supported |= (SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_1000baseT_Full);
-
- /* Use the vendor defined C22ext register for duplex settings */
- if (ecmd->speed != SPEED_10000 && !ecmd->autoneg) {
- reg = mdio_clause45_read(efx, phy_id, MDIO_MMD_C22EXT,
- GPHY_XCONTROL_REG);
- ecmd->duplex = (reg & (1 << GPHY_DUPLEX_LBN) ?
- DUPLEX_FULL : DUPLEX_HALF);
- }
+ return mdio_clause45_set_settings(efx, ecmd);
}
-static int sft9001_set_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
+static void sfx7101_set_npage_adv(struct efx_nic *efx, u32 advertising)
{
- int phy_id = efx->mii.phy_id;
- int rc;
-
- rc = mdio_clause45_set_settings(efx, ecmd);
- if (rc)
- return rc;
-
- if (ecmd->speed != SPEED_10000 && !ecmd->autoneg)
- mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_C22EXT,
- GPHY_XCONTROL_REG, GPHY_DUPLEX_LBN,
- ecmd->duplex == DUPLEX_FULL);
-
- return rc;
+ mdio_clause45_set_flag(efx, efx->mii.phy_id, MDIO_MMD_AN,
+ MDIO_AN_10GBT_CTRL,
+ MDIO_AN_10GBT_CTRL_ADV_10G_LBN,
+ advertising & ADVERTISED_10000baseT_Full);
}
-static bool sft9001_set_xnp_advertise(struct efx_nic *efx, u32 advertising)
+static void sft9001_set_npage_adv(struct efx_nic *efx, u32 advertising)
{
- int phy = efx->mii.phy_id;
- int reg = mdio_clause45_read(efx, phy, MDIO_MMD_PMAPMD,
- PMA_PMD_SPEED_ENABLE_REG);
- bool enabled;
-
- reg &= ~((1 << 2) | (1 << 3));
- if (EFX_WORKAROUND_13204(efx) &&
- (advertising & ADVERTISED_100baseT_Full))
- reg |= 1 << PMA_PMD_100TX_ADV_LBN;
- if (advertising & ADVERTISED_1000baseT_Full)
- reg |= 1 << PMA_PMD_1000T_ADV_LBN;
- if (advertising & ADVERTISED_10000baseT_Full)
- reg |= 1 << PMA_PMD_10000T_ADV_LBN;
- mdio_clause45_write(efx, phy, MDIO_MMD_PMAPMD,
- PMA_PMD_SPEED_ENABLE_REG, reg);
-
- enabled = (advertising &
- (ADVERTISED_1000baseT_Half |
- ADVERTISED_1000baseT_Full |
- ADVERTISED_10000baseT_Full));
- if (EFX_WORKAROUND_13204(efx))
- enabled |= (advertising & ADVERTISED_100baseT_Full);
- return enabled;
+ int phy_id = efx->mii.phy_id;
+
+ mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_C22EXT,
+ C22EXT_MSTSLV_CTRL,
+ C22EXT_MSTSLV_CTRL_ADV_1000_FD_LBN,
+ advertising & ADVERTISED_1000baseT_Full);
+ mdio_clause45_set_flag(efx, phy_id, MDIO_MMD_AN,
+ MDIO_AN_10GBT_CTRL,
+ MDIO_AN_10GBT_CTRL_ADV_10G_LBN,
+ advertising & ADVERTISED_10000baseT_Full);
}
struct efx_phy_operations falcon_sfx7101_phy_ops = {
.poll = tenxpress_phy_poll,
.fini = tenxpress_phy_fini,
.clear_interrupt = efx_port_dummy_op_void,
- .get_settings = sfx7101_get_settings,
- .set_settings = mdio_clause45_set_settings,
+ .get_settings = tenxpress_get_settings,
+ .set_settings = tenxpress_set_settings,
+ .set_npage_adv = sfx7101_set_npage_adv,
.num_tests = ARRAY_SIZE(sfx7101_test_names),
.test_names = sfx7101_test_names,
.run_tests = sfx7101_run_tests,
.poll = tenxpress_phy_poll,
.fini = tenxpress_phy_fini,
.clear_interrupt = efx_port_dummy_op_void,
- .get_settings = sft9001_get_settings,
- .set_settings = sft9001_set_settings,
- .set_xnp_advertise = sft9001_set_xnp_advertise,
+ .get_settings = tenxpress_get_settings,
+ .set_settings = tenxpress_set_settings,
+ .set_npage_adv = sft9001_set_npage_adv,
.num_tests = ARRAY_SIZE(sft9001_test_names),
.test_names = sft9001_test_names,
.run_tests = sft9001_run_tests,
projects / linux-2.6-omap-h63xx.git / blobdiff