#include "smc91x.h"
-#ifdef CONFIG_ISA
-/*
- * the LAN91C111 can be at any of the following port addresses. To change,
- * for a slightly different card, you can add it to the array. Keep in
- * mind that the array must end in zero.
- */
-static unsigned int smc_portlist[] __initdata = {
- 0x200, 0x220, 0x240, 0x260, 0x280, 0x2A0, 0x2C0, 0x2E0,
- 0x300, 0x320, 0x340, 0x360, 0x380, 0x3A0, 0x3C0, 0x3E0, 0
-};
-
-#ifndef SMC_IOADDR
-# define SMC_IOADDR -1
-#endif
-static unsigned long io = SMC_IOADDR;
-module_param(io, ulong, 0400);
-MODULE_PARM_DESC(io, "I/O base address");
-
-#ifndef SMC_IRQ
-# define SMC_IRQ -1
-#endif
-static int irq = SMC_IRQ;
-module_param(irq, int, 0400);
-MODULE_PARM_DESC(irq, "IRQ number");
-
-#endif /* CONFIG_ISA */
-
#ifndef SMC_NOWAIT
# define SMC_NOWAIT 0
#endif
PRINT_PKT(data, packet_len - 4);
- dev->last_rx = jiffies;
skb->protocol = eth_type_trans(skb, dev);
netif_rx(skb);
dev->stats.rx_packets++;
{
strncpy(info->driver, CARDNAME, sizeof(info->driver));
strncpy(info->version, version, sizeof(info->version));
- strncpy(info->bus_info, dev->dev.parent->bus_id, sizeof(info->bus_info));
+ strncpy(info->bus_info, dev_name(dev->dev.parent), sizeof(info->bus_info));
}
static int smc_ethtool_nwayreset(struct net_device *dev)
lp->msg_enable = level;
}
+static int smc_write_eeprom_word(struct net_device *dev, u16 addr, u16 word)
+{
+ u16 ctl;
+ struct smc_local *lp = netdev_priv(dev);
+ void __iomem *ioaddr = lp->base;
+
+ spin_lock_irq(&lp->lock);
+ /* load word into GP register */
+ SMC_SELECT_BANK(lp, 1);
+ SMC_SET_GP(lp, word);
+ /* set the address to put the data in EEPROM */
+ SMC_SELECT_BANK(lp, 2);
+ SMC_SET_PTR(lp, addr);
+ /* tell it to write */
+ SMC_SELECT_BANK(lp, 1);
+ ctl = SMC_GET_CTL(lp);
+ SMC_SET_CTL(lp, ctl | (CTL_EEPROM_SELECT | CTL_STORE));
+ /* wait for it to finish */
+ do {
+ udelay(1);
+ } while (SMC_GET_CTL(lp) & CTL_STORE);
+ /* clean up */
+ SMC_SET_CTL(lp, ctl);
+ SMC_SELECT_BANK(lp, 2);
+ spin_unlock_irq(&lp->lock);
+ return 0;
+}
+
+static int smc_read_eeprom_word(struct net_device *dev, u16 addr, u16 *word)
+{
+ u16 ctl;
+ struct smc_local *lp = netdev_priv(dev);
+ void __iomem *ioaddr = lp->base;
+
+ spin_lock_irq(&lp->lock);
+ /* set the EEPROM address to get the data from */
+ SMC_SELECT_BANK(lp, 2);
+ SMC_SET_PTR(lp, addr | PTR_READ);
+ /* tell it to load */
+ SMC_SELECT_BANK(lp, 1);
+ SMC_SET_GP(lp, 0xffff); /* init to known */
+ ctl = SMC_GET_CTL(lp);
+ SMC_SET_CTL(lp, ctl | (CTL_EEPROM_SELECT | CTL_RELOAD));
+ /* wait for it to finish */
+ do {
+ udelay(1);
+ } while (SMC_GET_CTL(lp) & CTL_RELOAD);
+ /* read word from GP register */
+ *word = SMC_GET_GP(lp);
+ /* clean up */
+ SMC_SET_CTL(lp, ctl);
+ SMC_SELECT_BANK(lp, 2);
+ spin_unlock_irq(&lp->lock);
+ return 0;
+}
+
+static int smc_ethtool_geteeprom_len(struct net_device *dev)
+{
+ return 0x23 * 2;
+}
+
+static int smc_ethtool_geteeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ int i;
+ int imax;
+
+ DBG(1, "Reading %d bytes at %d(0x%x)\n",
+ eeprom->len, eeprom->offset, eeprom->offset);
+ imax = smc_ethtool_geteeprom_len(dev);
+ for (i = 0; i < eeprom->len; i += 2) {
+ int ret;
+ u16 wbuf;
+ int offset = i + eeprom->offset;
+ if (offset > imax)
+ break;
+ ret = smc_read_eeprom_word(dev, offset >> 1, &wbuf);
+ if (ret != 0)
+ return ret;
+ DBG(2, "Read 0x%x from 0x%x\n", wbuf, offset >> 1);
+ data[i] = (wbuf >> 8) & 0xff;
+ data[i+1] = wbuf & 0xff;
+ }
+ return 0;
+}
+
+static int smc_ethtool_seteeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ int i;
+ int imax;
+
+ DBG(1, "Writing %d bytes to %d(0x%x)\n",
+ eeprom->len, eeprom->offset, eeprom->offset);
+ imax = smc_ethtool_geteeprom_len(dev);
+ for (i = 0; i < eeprom->len; i += 2) {
+ int ret;
+ u16 wbuf;
+ int offset = i + eeprom->offset;
+ if (offset > imax)
+ break;
+ wbuf = (data[i] << 8) | data[i + 1];
+ DBG(2, "Writing 0x%x to 0x%x\n", wbuf, offset >> 1);
+ ret = smc_write_eeprom_word(dev, offset >> 1, wbuf);
+ if (ret != 0)
+ return ret;
+ }
+ return 0;
+}
+
+
static const struct ethtool_ops smc_ethtool_ops = {
.get_settings = smc_ethtool_getsettings,
.set_settings = smc_ethtool_setsettings,
.set_msglevel = smc_ethtool_setmsglevel,
.nway_reset = smc_ethtool_nwayreset,
.get_link = ethtool_op_get_link,
-// .get_eeprom = smc_ethtool_geteeprom,
-// .set_eeprom = smc_ethtool_seteeprom,
+ .get_eeprom_len = smc_ethtool_geteeprom_len,
+ .get_eeprom = smc_ethtool_geteeprom,
+ .set_eeprom = smc_ethtool_seteeprom,
};
/*
int retval;
unsigned int val, revision_register;
const char *version_string;
- DECLARE_MAC_BUF(mac);
DBG(2, "%s: %s\n", CARDNAME, __func__);
"set using ifconfig\n", dev->name);
} else {
/* Print the Ethernet address */
- printk("%s: Ethernet addr: %s\n",
- dev->name, print_mac(mac, dev->dev_addr));
+ printk("%s: Ethernet addr: %pM\n",
+ dev->name, dev->dev_addr);
}
if (lp->phy_type == 0) {
static int __init smc_init(void)
{
-#ifdef MODULE
-#ifdef CONFIG_ISA
- if (io == -1)
- printk(KERN_WARNING
- "%s: You shouldn't use auto-probing with insmod!\n",
- CARDNAME);
-#endif
-#endif
-
return platform_driver_register(&smc_driver);
}