*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
/* RSSI to dBm */
#define IWL_RSSI_OFFSET 44
-/*
- * EEPROM related constants, enums, and structures.
- */
-
-/*
- * EEPROM access time values:
- *
- * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
- * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
- * CSR_EEPROM_REG_BIT_CMD (0x2).
- * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
- * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
- * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
- */
-#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
-#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
-
-/*
- * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
- *
- * IBSS and/or AP operation is allowed *only* on those channels with
- * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
- * RADAR detection is not supported by the 4965 driver, but is a
- * requirement for establishing a new network for legal operation on channels
- * requiring RADAR detection or restricting ACTIVE scanning.
- *
- * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
- * It only indicates that 20 MHz channel use is supported; FAT channel
- * usage is indicated by a separate set of regulatory flags for each
- * FAT channel pair.
- *
- * NOTE: Using a channel inappropriately will result in a uCode error!
- */
-enum {
- EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
- EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
- /* Bit 2 Reserved */
- EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
- EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
- EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
- EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
- EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
-};
-
-/* SKU Capabilities */
-#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
-#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
-
-/* *regulatory* channel data format in eeprom, one for each channel.
- * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
-struct iwl4965_eeprom_channel {
- u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
- s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
-} __attribute__ ((packed));
-
-/* 4965 has two radio transmitters (and 3 radio receivers) */
-#define EEPROM_TX_POWER_TX_CHAINS (2)
-
-/* 4965 has room for up to 8 sets of txpower calibration data */
-#define EEPROM_TX_POWER_BANDS (8)
-
-/* 4965 factory calibration measures txpower gain settings for
- * each of 3 target output levels */
-#define EEPROM_TX_POWER_MEASUREMENTS (3)
-
-/* 4965 driver does not work with txpower calibration version < 5.
- * Look for this in calib_version member of struct iwl4965_eeprom. */
-#define EEPROM_TX_POWER_VERSION_NEW (5)
-
-
-/*
- * 4965 factory calibration data for one txpower level, on one channel,
- * measured on one of the 2 tx chains (radio transmitter and associated
- * antenna). EEPROM contains:
- *
- * 1) Temperature (degrees Celsius) of device when measurement was made.
- *
- * 2) Gain table index used to achieve the target measurement power.
- * This refers to the "well-known" gain tables (see iwl-4965-hw.h).
- *
- * 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
- *
- * 4) RF power amplifier detector level measurement (not used).
- */
-struct iwl4965_eeprom_calib_measure {
- u8 temperature; /* Device temperature (Celsius) */
- u8 gain_idx; /* Index into gain table */
- u8 actual_pow; /* Measured RF output power, half-dBm */
- s8 pa_det; /* Power amp detector level (not used) */
-} __attribute__ ((packed));
-
-
-/*
- * 4965 measurement set for one channel. EEPROM contains:
- *
- * 1) Channel number measured
- *
- * 2) Measurements for each of 3 power levels for each of 2 radio transmitters
- * (a.k.a. "tx chains") (6 measurements altogether)
- */
-struct iwl4965_eeprom_calib_ch_info {
- u8 ch_num;
- struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
- [EEPROM_TX_POWER_MEASUREMENTS];
-} __attribute__ ((packed));
-
-/*
- * 4965 txpower subband info.
- *
- * For each frequency subband, EEPROM contains the following:
- *
- * 1) First and last channels within range of the subband. "0" values
- * indicate that this sample set is not being used.
- *
- * 2) Sample measurement sets for 2 channels close to the range endpoints.
- */
-struct iwl4965_eeprom_calib_subband_info {
- u8 ch_from; /* channel number of lowest channel in subband */
- u8 ch_to; /* channel number of highest channel in subband */
- struct iwl4965_eeprom_calib_ch_info ch1;
- struct iwl4965_eeprom_calib_ch_info ch2;
-} __attribute__ ((packed));
-
-
-/*
- * 4965 txpower calibration info. EEPROM contains:
- *
- * 1) Factory-measured saturation power levels (maximum levels at which
- * tx power amplifier can output a signal without too much distortion).
- * There is one level for 2.4 GHz band and one for 5 GHz band. These
- * values apply to all channels within each of the bands.
- *
- * 2) Factory-measured power supply voltage level. This is assumed to be
- * constant (i.e. same value applies to all channels/bands) while the
- * factory measurements are being made.
- *
- * 3) Up to 8 sets of factory-measured txpower calibration values.
- * These are for different frequency ranges, since txpower gain
- * characteristics of the analog radio circuitry vary with frequency.
- *
- * Not all sets need to be filled with data;
- * struct iwl4965_eeprom_calib_subband_info contains range of channels
- * (0 if unused) for each set of data.
- */
-struct iwl4965_eeprom_calib_info {
- u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
- u8 saturation_power52; /* half-dBm */
- s16 voltage; /* signed */
- struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
-} __attribute__ ((packed));
-
-
-/*
- * 4965 EEPROM map
- */
-struct iwl4965_eeprom {
- u8 reserved0[16];
-#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
- u16 device_id; /* abs.ofs: 16 */
- u8 reserved1[2];
-#define EEPROM_PMC (2*0x0A) /* 2 bytes */
- u16 pmc; /* abs.ofs: 20 */
- u8 reserved2[20];
-#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
- u8 mac_address[6]; /* abs.ofs: 42 */
- u8 reserved3[58];
-#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
- u16 board_revision; /* abs.ofs: 106 */
- u8 reserved4[11];
-#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
- u8 board_pba_number[9]; /* abs.ofs: 119 */
- u8 reserved5[8];
-#define EEPROM_VERSION (2*0x44) /* 2 bytes */
- u16 version; /* abs.ofs: 136 */
-#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
- u8 sku_cap; /* abs.ofs: 138 */
-#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
- u8 leds_mode; /* abs.ofs: 139 */
-#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
- u16 oem_mode;
-#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
- u16 wowlan_mode; /* abs.ofs: 142 */
-#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
- u16 leds_time_interval; /* abs.ofs: 144 */
-#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
- u8 leds_off_time; /* abs.ofs: 146 */
-#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
- u8 leds_on_time; /* abs.ofs: 147 */
-#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
- u8 almgor_m_version; /* abs.ofs: 148 */
-#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
- u8 antenna_switch_type; /* abs.ofs: 149 */
- u8 reserved6[8];
-#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
- u16 board_revision_4965; /* abs.ofs: 158 */
- u8 reserved7[13];
-#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
- u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
- u8 reserved8[10];
-#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
- u8 sku_id[4]; /* abs.ofs: 192 */
-
-/*
- * Per-channel regulatory data.
- *
- * Each channel that *might* be supported by 3945 or 4965 has a fixed location
- * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
- * txpower (MSB).
- *
- * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
- * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
- *
- * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
- */
-#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
- u16 band_1_count; /* abs.ofs: 196 */
-#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
- struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
-
-/*
- * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
- * 5.0 GHz channels 7, 8, 11, 12, 16
- * (4915-5080MHz) (none of these is ever supported)
- */
-#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
- u16 band_2_count; /* abs.ofs: 226 */
-#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
- struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
-
-/*
- * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
- * (5170-5320MHz)
- */
-#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
- u16 band_3_count; /* abs.ofs: 254 */
-#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
- struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
-
-/*
- * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
- * (5500-5700MHz)
- */
-#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
- u16 band_4_count; /* abs.ofs: 280 */
-#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
- struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
-
-/*
- * 5.7 GHz channels 145, 149, 153, 157, 161, 165
- * (5725-5825MHz)
- */
-#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
- u16 band_5_count; /* abs.ofs: 304 */
-#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
- struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
-
- u8 reserved10[2];
-
-
-/*
- * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
- *
- * The channel listed is the center of the lower 20 MHz half of the channel.
- * The overall center frequency is actually 2 channels (10 MHz) above that,
- * and the upper half of each FAT channel is centered 4 channels (20 MHz) away
- * from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
- * and the overall FAT channel width centers on channel 3.
- *
- * NOTE: The RXON command uses 20 MHz channel numbers to specify the
- * control channel to which to tune. RXON also specifies whether the
- * control channel is the upper or lower half of a FAT channel.
- *
- * NOTE: 4965 does not support FAT channels on 2.4 GHz.
- */
-#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
- struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
- u8 reserved11[2];
-
-/*
- * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
- * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
- */
-#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
- struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
- u8 reserved12[6];
-
-/*
- * 4965 driver requires txpower calibration format version 5 or greater.
- * Driver does not work with txpower calibration version < 5.
- * This value is simply a 16-bit number, no major/minor versions here.
- */
-#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
- u16 calib_version; /* abs.ofs: 364 */
- u8 reserved13[2];
- u8 reserved14[96]; /* abs.ofs: 368 */
-
-/*
- * 4965 Txpower calibration data.
- */
-#define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */
- struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */
-
- u8 reserved16[140]; /* fill out to full 1024 byte block */
-
-
-} __attribute__ ((packed));
-
-#define IWL_EEPROM_IMAGE_SIZE 1024
-
-/* End of EEPROM */
#include "iwl-4965-commands.h"
#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
-/*=== CSR (control and status registers) ===*/
-#define CSR_BASE (0x000)
-
-#define CSR_SW_VER (CSR_BASE+0x000)
-#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
-#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
-#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
-#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
-#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
-#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
-#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
-#define CSR_GP_CNTRL (CSR_BASE+0x024)
-
-/*
- * Hardware revision info
- * Bit fields:
- * 31-8: Reserved
- * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
- * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
- * 1-0: "Dash" value, as in A-1, etc.
- *
- * NOTE: Revision step affects calculation of CCK txpower for 4965.
- */
-#define CSR_HW_REV (CSR_BASE+0x028)
-
-/* EEPROM reads */
-#define CSR_EEPROM_REG (CSR_BASE+0x02c)
-#define CSR_EEPROM_GP (CSR_BASE+0x030)
-#define CSR_GP_UCODE (CSR_BASE+0x044)
-#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
-#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
-#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
-#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-
-/*
- * Indicates hardware rev, to determine CCK backoff for txpower calculation.
- * Bit fields:
- * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
- */
-#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
-
-/* Hardware interface configuration bits */
-#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010)
-#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
-#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
-
-/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
- * acknowledged (reset) by host writing "1" to flagged bits. */
-#define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */
-#define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */
-#define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */
-#define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */
-#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */
-#define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */
-#define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */
-#define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */
-#define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */
-#define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */
-#define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */
-
-#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
- CSR_INT_BIT_HW_ERR | \
- CSR_INT_BIT_FH_TX | \
- CSR_INT_BIT_SW_ERR | \
- CSR_INT_BIT_RF_KILL | \
- CSR_INT_BIT_SW_RX | \
- CSR_INT_BIT_WAKEUP | \
- CSR_INT_BIT_ALIVE)
-
-/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
-#define CSR_FH_INT_BIT_ERR (1<<31) /* Error */
-#define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */
-#define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */
-#define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */
-#define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */
-#define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */
-
-#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
- CSR_FH_INT_BIT_RX_CHNL1 | \
- CSR_FH_INT_BIT_RX_CHNL0)
-
-#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
- CSR_FH_INT_BIT_TX_CHNL0)
-
-
-/* RESET */
-#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
-#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
-#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
-#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
-#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
-
-/* GP (general purpose) CONTROL */
-#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
-#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
-#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
-
-#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
-
-#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
-#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
-
-
-/* EEPROM REG */
-#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
-#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
-
-/* EEPROM GP */
-#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
-#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
-#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
-
-/* UCODE DRV GP */
-#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
-#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
-#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
-#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
-
-/* GPIO */
-#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
-#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
-#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
-
-/* GI Chicken Bits */
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-
-/*=== HBUS (Host-side Bus) ===*/
-#define HBUS_BASE (0x400)
-
-/*
- * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
- * structures, error log, event log, verifying uCode load).
- * First write to address register, then read from or write to data register
- * to complete the job. Once the address register is set up, accesses to
- * data registers auto-increment the address by one dword.
- * Bit usage for address registers (read or write):
- * 0-31: memory address within device
- */
-#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
-#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
-#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
-#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
-
-/*
- * Registers for accessing device's internal peripheral registers
- * (e.g. SCD, BSM, etc.). First write to address register,
- * then read from or write to data register to complete the job.
- * Bit usage for address registers (read or write):
- * 0-15: register address (offset) within device
- * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
- */
-#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
-#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
-#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
-#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
-
-/*
- * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
- * Driver sets this to indicate index to next TFD that driver will fill
- * (1 past latest filled).
- * Bit usage:
- * 0-7: queue write index (0-255)
- * 11-8: queue selector (0-15)
- */
-#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
-
-#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
-
-#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
-
#define TFD_QUEUE_SIZE_MAX (256)
#define IWL_NUM_SCAN_RATES (2)
#define TFD_TX_CMD_SLOTS 256
#define TFD_CMD_SLOTS 32
-#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \
- sizeof(struct iwl4965_cmd_meta))
-
/*
* RX related structures and functions
*/
#define RX_LOW_WATERMARK 8
/* Size of one Rx buffer in host DRAM */
-#define IWL_RX_BUF_SIZE (4 * 1024)
+#define IWL_RX_BUF_SIZE_4K (4 * 1024)
+#define IWL_RX_BUF_SIZE_8K (8 * 1024)
/* Sizes and addresses for instruction and data memory (SRAM) in
* 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
#define RTC_INST_LOWER_BOUND (0x000000)
-#define KDR_RTC_INST_UPPER_BOUND (0x018000)
+#define IWL49_RTC_INST_UPPER_BOUND (0x018000)
#define RTC_DATA_LOWER_BOUND (0x800000)
-#define KDR_RTC_DATA_UPPER_BOUND (0x80A000)
+#define IWL49_RTC_DATA_UPPER_BOUND (0x80A000)
-#define KDR_RTC_INST_SIZE (KDR_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
-#define KDR_RTC_DATA_SIZE (KDR_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
+#define IWL49_RTC_INST_SIZE \
+ (IWL49_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
+#define IWL49_RTC_DATA_SIZE \
+ (IWL49_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
-#define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE
-#define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE
+#define IWL_MAX_INST_SIZE IWL49_RTC_INST_SIZE
+#define IWL_MAX_DATA_SIZE IWL49_RTC_DATA_SIZE
/* Size of uCode instruction memory in bootstrap state machine */
#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE
static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
{
return (addr >= RTC_DATA_LOWER_BOUND) &&
- (addr < KDR_RTC_DATA_UPPER_BOUND);
+ (addr < IWL49_RTC_DATA_UPPER_BOUND);
}
/********************* START TEMPERATURE *************************************/
#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */
#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20)
-#define FH_RCSR_RX_CONFIG_RB_SIZE_BITSHIFT (16)
+#define FH_RCSR_RX_CONFIG_REG_IRQ_RBTH_BITSHIFT (4)
+#define RX_RB_TIMEOUT (0x10)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
-#define IWL_FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl))
+/********************* START TX SCHEDULER *************************************/
+
+/**
+ * 4965 Tx Scheduler
+ *
+ * The Tx Scheduler selects the next frame to be transmitted, chosing TFDs
+ * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
+ * host DRAM. It steers each frame's Tx command (which contains the frame
+ * data) into one of up to 7 prioritized Tx DMA FIFO channels within the
+ * device. A queue maps to only one (selectable by driver) Tx DMA channel,
+ * but one DMA channel may take input from several queues.
+ *
+ * Tx DMA channels have dedicated purposes. For 4965, they are used as follows:
+ *
+ * 0 -- EDCA BK (background) frames, lowest priority
+ * 1 -- EDCA BE (best effort) frames, normal priority
+ * 2 -- EDCA VI (video) frames, higher priority
+ * 3 -- EDCA VO (voice) and management frames, highest priority
+ * 4 -- Commands (e.g. RXON, etc.)
+ * 5 -- HCCA short frames
+ * 6 -- HCCA long frames
+ * 7 -- not used by driver (device-internal only)
+ *
+ * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
+ * In addition, driver can map queues 7-15 to Tx DMA/FIFO channels 0-3 to
+ * support 11n aggregation via EDCA DMA channels.
+ *
+ * The driver sets up each queue to work in one of two modes:
+ *
+ * 1) Scheduler-Ack, in which the scheduler automatically supports a
+ * block-ack (BA) window of up to 64 TFDs. In this mode, each queue
+ * contains TFDs for a unique combination of Recipient Address (RA)
+ * and Traffic Identifier (TID), that is, traffic of a given
+ * Quality-Of-Service (QOS) priority, destined for a single station.
+ *
+ * In scheduler-ack mode, the scheduler keeps track of the Tx status of
+ * each frame within the BA window, including whether it's been transmitted,
+ * and whether it's been acknowledged by the receiving station. The device
+ * automatically processes block-acks received from the receiving STA,
+ * and reschedules un-acked frames to be retransmitted (successful
+ * Tx completion may end up being out-of-order).
+ *
+ * The driver must maintain the queue's Byte Count table in host DRAM
+ * (struct iwl4965_sched_queue_byte_cnt_tbl) for this mode.
+ * This mode does not support fragmentation.
+ *
+ * 2) FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
+ * The device may automatically retry Tx, but will retry only one frame
+ * at a time, until receiving ACK from receiving station, or reaching
+ * retry limit and giving up.
+ *
+ * The command queue (#4) must use this mode!
+ * This mode does not require use of the Byte Count table in host DRAM.
+ *
+ * Driver controls scheduler operation via 3 means:
+ * 1) Scheduler registers
+ * 2) Shared scheduler data base in internal 4956 SRAM
+ * 3) Shared data in host DRAM
+ *
+ * Initialization:
+ *
+ * When loading, driver should allocate memory for:
+ * 1) 16 TFD circular buffers, each with space for (typically) 256 TFDs.
+ * 2) 16 Byte Count circular buffers in 16 KBytes contiguous memory
+ * (1024 bytes for each queue).
+ *
+ * After receiving "Alive" response from uCode, driver must initialize
+ * the scheduler (especially for queue #4, the command queue, otherwise
+ * the driver can't issue commands!):
+ */
+
+/**
+ * Max Tx window size is the max number of contiguous TFDs that the scheduler
+ * can keep track of at one time when creating block-ack chains of frames.
+ * Note that "64" matches the number of ack bits in a block-ack packet.
+ * Driver should use SCD_WIN_SIZE and SCD_FRAME_LIMIT values to initialize
+ * SCD_CONTEXT_QUEUE_OFFSET(x) values.
+ */
#define SCD_WIN_SIZE 64
#define SCD_FRAME_LIMIT 64
-/* SRAM structures */
-#define SCD_CONTEXT_DATA_OFFSET 0x380
-#define SCD_TX_STTS_BITMAP_OFFSET 0x400
-#define SCD_TRANSLATE_TBL_OFFSET 0x500
-#define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
-#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
- ((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
+/* SCD registers are internal, must be accessed via HBUS_TARG_PRPH regs */
+#define SCD_START_OFFSET 0xa02c00
+/*
+ * 4965 tells driver SRAM address for internal scheduler structs via this reg.
+ * Value is valid only after "Alive" response from uCode.
+ */
+#define SCD_SRAM_BASE_ADDR (SCD_START_OFFSET + 0x0)
+
+/*
+ * Driver may need to update queue-empty bits after changing queue's
+ * write and read pointers (indexes) during (re-)initialization (i.e. when
+ * scheduler is not tracking what's happening).
+ * Bit fields:
+ * 31-16: Write mask -- 1: update empty bit, 0: don't change empty bit
+ * 15-00: Empty state, one for each queue -- 1: empty, 0: non-empty
+ * NOTE: This register is not used by Linux driver.
+ */
+#define SCD_EMPTY_BITS (SCD_START_OFFSET + 0x4)
+
+/*
+ * Physical base address of array of byte count (BC) circular buffers (CBs).
+ * Each Tx queue has a BC CB in host DRAM to support Scheduler-ACK mode.
+ * This register points to BC CB for queue 0, must be on 1024-byte boundary.
+ * Others are spaced by 1024 bytes.
+ * Each BC CB is 2 bytes * (256 + 64) = 740 bytes, followed by 384 bytes pad.
+ * (Index into a queue's BC CB) = (index into queue's TFD CB) = (SSN & 0xff).
+ * Bit fields:
+ * 25-00: Byte Count CB physical address [35:10], must be 1024-byte aligned.
+ */
+#define SCD_DRAM_BASE_ADDR (SCD_START_OFFSET + 0x10)
+
+/*
+ * Enables any/all Tx DMA/FIFO channels.
+ * Scheduler generates requests for only the active channels.
+ * Set this to 0xff to enable all 8 channels (normal usage).
+ * Bit fields:
+ * 7- 0: Enable (1), disable (0), one bit for each channel 0-7
+ */
+#define SCD_TXFACT (SCD_START_OFFSET + 0x1c)
+
+/* Mask to enable contiguous Tx DMA/FIFO channels between "lo" and "hi". */
#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
- ((1<<(hi))|((1<<(hi))-(1<<(lo))))
+ ((1 << (hi)) | ((1 << (hi)) - (1 << (lo))))
+
+/*
+ * Queue (x) Write Pointers (indexes, really!), one for each Tx queue.
+ * Initialized and updated by driver as new TFDs are added to queue.
+ * NOTE: If using Block Ack, index must correspond to frame's
+ * Start Sequence Number; index = (SSN & 0xff)
+ * NOTE: Alternative to HBUS_TARG_WRPTR, which is what Linux driver uses?
+ */
+#define SCD_QUEUE_WRPTR(x) (SCD_START_OFFSET + 0x24 + (x) * 4)
+/*
+ * Queue (x) Read Pointers (indexes, really!), one for each Tx queue.
+ * For FIFO mode, index indicates next frame to transmit.
+ * For Scheduler-ACK mode, index indicates first frame in Tx window.
+ * Initialized by driver, updated by scheduler.
+ */
+#define SCD_QUEUE_RDPTR(x) (SCD_START_OFFSET + 0x64 + (x) * 4)
+
+/*
+ * Select which queues work in chain mode (1) vs. not (0).
+ * Use chain mode to build chains of aggregated frames.
+ * Bit fields:
+ * 31-16: Reserved
+ * 15-00: Mode, one bit for each queue -- 1: Chain mode, 0: one-at-a-time
+ * NOTE: If driver sets up queue for chain mode, it should be also set up
+ * Scheduler-ACK mode as well, via SCD_QUEUE_STATUS_BITS(x).
+ */
+#define SCD_QUEUECHAIN_SEL (SCD_START_OFFSET + 0xd0)
+
+/*
+ * Select which queues interrupt driver when scheduler increments
+ * a queue's read pointer (index).
+ * Bit fields:
+ * 31-16: Reserved
+ * 15-00: Interrupt enable, one bit for each queue -- 1: enabled, 0: disabled
+ * NOTE: This functionality is apparently a no-op; driver relies on interrupts
+ * from Rx queue to read Tx command responses and update Tx queues.
+ */
+#define SCD_INTERRUPT_MASK (SCD_START_OFFSET + 0xe4)
+
+/*
+ * Queue search status registers. One for each queue.
+ * Sets up queue mode and assigns queue to Tx DMA channel.
+ * Bit fields:
+ * 19-10: Write mask/enable bits for bits 0-9
+ * 9: Driver should init to "0"
+ * 8: Scheduler-ACK mode (1), non-Scheduler-ACK (i.e. FIFO) mode (0).
+ * Driver should init to "1" for aggregation mode, or "0" otherwise.
+ * 7-6: Driver should init to "0"
+ * 5: Window Size Left; indicates whether scheduler can request
+ * another TFD, based on window size, etc. Driver should init
+ * this bit to "1" for aggregation mode, or "0" for non-agg.
+ * 4-1: Tx FIFO to use (range 0-7).
+ * 0: Queue is active (1), not active (0).
+ * Other bits should be written as "0"
+ *
+ * NOTE: If enabling Scheduler-ACK mode, chain mode should also be enabled
+ * via SCD_QUEUECHAIN_SEL.
+ */
+#define SCD_QUEUE_STATUS_BITS(x) (SCD_START_OFFSET + 0x104 + (x) * 4)
+
+/* Bit field positions */
#define SCD_QUEUE_STTS_REG_POS_ACTIVE (0)
#define SCD_QUEUE_STTS_REG_POS_TXF (1)
#define SCD_QUEUE_STTS_REG_POS_WSL (5)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACK (8)
+
+/* Write masks */
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10)
#define SCD_QUEUE_STTS_REG_MSK (0x0007FC00)
+/**
+ * 4965 internal SRAM structures for scheduler, shared with driver ...
+ *
+ * Driver should clear and initialize the following areas after receiving
+ * "Alive" response from 4965 uCode, i.e. after initial
+ * uCode load, or after a uCode load done for error recovery:
+ *
+ * SCD_CONTEXT_DATA_OFFSET (size 128 bytes)
+ * SCD_TX_STTS_BITMAP_OFFSET (size 256 bytes)
+ * SCD_TRANSLATE_TBL_OFFSET (size 32 bytes)
+ *
+ * Driver accesses SRAM via HBUS_TARG_MEM_* registers.
+ * Driver reads base address of this scheduler area from SCD_SRAM_BASE_ADDR.
+ * All OFFSET values must be added to this base address.
+ */
+
+/*
+ * Queue context. One 8-byte entry for each of 16 queues.
+ *
+ * Driver should clear this entire area (size 0x80) to 0 after receiving
+ * "Alive" notification from uCode. Additionally, driver should init
+ * each queue's entry as follows:
+ *
+ * LS Dword bit fields:
+ * 0-06: Max Tx window size for Scheduler-ACK. Driver should init to 64.
+ *
+ * MS Dword bit fields:
+ * 16-22: Frame limit. Driver should init to 10 (0xa).
+ *
+ * Driver should init all other bits to 0.
+ *
+ * Init must be done after driver receives "Alive" response from 4965 uCode,
+ * and when setting up queue for aggregation.
+ */
+#define SCD_CONTEXT_DATA_OFFSET 0x380
+#define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
+
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F)
-
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000)
+/*
+ * Tx Status Bitmap
+ *
+ * Driver should clear this entire area (size 0x100) to 0 after receiving
+ * "Alive" notification from uCode. Area is used only by device itself;
+ * no other support (besides clearing) is required from driver.
+ */
+#define SCD_TX_STTS_BITMAP_OFFSET 0x400
+
+/*
+ * RAxTID to queue translation mapping.
+ *
+ * When queue is in Scheduler-ACK mode, frames placed in a that queue must be
+ * for only one combination of receiver address (RA) and traffic ID (TID), i.e.
+ * one QOS priority level destined for one station (for this wireless link,
+ * not final destination). The SCD_TRANSLATE_TABLE area provides 16 16-bit
+ * mappings, one for each of the 16 queues. If queue is not in Scheduler-ACK
+ * mode, the device ignores the mapping value.
+ *
+ * Bit fields, for each 16-bit map:
+ * 15-9: Reserved, set to 0
+ * 8-4: Index into device's station table for recipient station
+ * 3-0: Traffic ID (tid), range 0-15
+ *
+ * Driver should clear this entire area (size 32 bytes) to 0 after receiving
+ * "Alive" notification from uCode. To update a 16-bit map value, driver
+ * must read a dword-aligned value from device SRAM, replace the 16-bit map
+ * value of interest, and write the dword value back into device SRAM.
+ */
+#define SCD_TRANSLATE_TBL_OFFSET 0x500
+
+/* Find translation table dword to read/write for given queue */
+#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
+ ((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
+
+#define SCD_TXFIFO_POS_TID (0)
+#define SCD_TXFIFO_POS_RA (4)
+#define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)
+
+/*********************** END TX SCHEDULER *************************************/
+
static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFF;
* up to 7 DMA channels (FIFOs). Each Tx queue is supported by a circular array
* in DRAM containing 256 Transmit Frame Descriptors (TFDs).
*/
-#define IWL4965_MAX_WIN_SIZE 64
-#define IWL4965_QUEUE_SIZE 256
-#define IWL4965_NUM_FIFOS 7
-#define IWL_MAX_NUM_QUEUES 16
+#define IWL4965_MAX_WIN_SIZE 64
+#define IWL4965_QUEUE_SIZE 256
+#define IWL4965_NUM_FIFOS 7
+#define IWL4965_MAX_NUM_QUEUES 16
/**
*/
struct iwl4965_shared {
struct iwl4965_sched_queue_byte_cnt_tbl
- queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES];
- __le32 val0;
+ queues_byte_cnt_tbls[IWL4965_MAX_NUM_QUEUES];
+ __le32 rb_closed;
/* __le32 rb_closed_stts_rb_num:12; */
#define IWL_rb_closed_stts_rb_num_POS 0
#define IWL_rb_closed_stts_rb_num_LEN 12
-#define IWL_rb_closed_stts_rb_num_SYM val0
+#define IWL_rb_closed_stts_rb_num_SYM rb_closed
/* __le32 rsrv1:4; */
/* __le32 rb_closed_stts_rx_frame_num:12; */
#define IWL_rb_closed_stts_rx_frame_num_POS 16
#define IWL_rb_closed_stts_rx_frame_num_LEN 12
-#define IWL_rb_closed_stts_rx_frame_num_SYM val0
+#define IWL_rb_closed_stts_rx_frame_num_SYM rb_closed
/* __le32 rsrv2:4; */
- __le32 val1;
+ __le32 frm_finished;
/* __le32 frame_finished_stts_rb_num:12; */
#define IWL_frame_finished_stts_rb_num_POS 0
#define IWL_frame_finished_stts_rb_num_LEN 12
-#define IWL_frame_finished_stts_rb_num_SYM val1
+#define IWL_frame_finished_stts_rb_num_SYM frm_finished
/* __le32 rsrv3:4; */
/* __le32 frame_finished_stts_rx_frame_num:12; */
#define IWL_frame_finished_stts_rx_frame_num_POS 16
#define IWL_frame_finished_stts_rx_frame_num_LEN 12
-#define IWL_frame_finished_stts_rx_frame_num_SYM val1
+#define IWL_frame_finished_stts_rx_frame_num_SYM frm_finished
/* __le32 rsrv4:4; */
__le32 padding1; /* so that allocation will be aligned to 16B */