MODULE_DEVICE_TABLE(pci, rtl8180_table);
+static const struct ieee80211_rate rtl818x_rates[] = {
+ { .bitrate = 10, .hw_value = 0, },
+ { .bitrate = 20, .hw_value = 1, },
+ { .bitrate = 55, .hw_value = 2, },
+ { .bitrate = 110, .hw_value = 3, },
+ { .bitrate = 60, .hw_value = 4, },
+ { .bitrate = 90, .hw_value = 5, },
+ { .bitrate = 120, .hw_value = 6, },
+ { .bitrate = 180, .hw_value = 7, },
+ { .bitrate = 240, .hw_value = 8, },
+ { .bitrate = 360, .hw_value = 9, },
+ { .bitrate = 480, .hw_value = 10, },
+ { .bitrate = 540, .hw_value = 11, },
+};
+
+static const struct ieee80211_channel rtl818x_channels[] = {
+ { .center_freq = 2412 },
+ { .center_freq = 2417 },
+ { .center_freq = 2422 },
+ { .center_freq = 2427 },
+ { .center_freq = 2432 },
+ { .center_freq = 2437 },
+ { .center_freq = 2442 },
+ { .center_freq = 2447 },
+ { .center_freq = 2452 },
+ { .center_freq = 2457 },
+ { .center_freq = 2462 },
+ { .center_freq = 2467 },
+ { .center_freq = 2472 },
+ { .center_freq = 2484 },
+};
+
+
+
+
void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
{
struct rtl8180_priv *priv = dev->priv;
rx_status.antenna = (flags2 >> 15) & 1;
/* TODO: improve signal/rssi reporting */
- rx_status.signal = flags2 & 0xFF;
- rx_status.ssi = (flags2 >> 8) & 0x7F;
- rx_status.rate = (flags >> 20) & 0xF;
- rx_status.freq = dev->conf.freq;
- rx_status.channel = dev->conf.channel;
- rx_status.phymode = dev->conf.phymode;
+ rx_status.qual = flags2 & 0xFF;
+ rx_status.signal = (flags2 >> 8) & 0x7F;
+ /* XXX: is this correct? */
+ rx_status.rate_idx = (flags >> 20) & 0xF;
+ rx_status.freq = dev->conf.channel->center_freq;
+ rx_status.band = dev->conf.channel->band;
rx_status.mactime = le64_to_cpu(entry->tsft);
rx_status.flag |= RX_FLAG_TSFT;
if (flags & RTL8180_RX_DESC_FLAG_CRC32_ERR)
while (skb_queue_len(&ring->queue)) {
struct rtl8180_tx_desc *entry = &ring->desc[ring->idx];
struct sk_buff *skb;
- struct ieee80211_tx_status status;
- struct ieee80211_tx_control *control;
+ struct ieee80211_tx_info *info;
u32 flags = le32_to_cpu(entry->flags);
if (flags & RTL8180_TX_DESC_FLAG_OWN)
return;
- memset(&status, 0, sizeof(status));
-
ring->idx = (ring->idx + 1) % ring->entries;
skb = __skb_dequeue(&ring->queue);
pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf),
skb->len, PCI_DMA_TODEVICE);
- control = *((struct ieee80211_tx_control **)skb->cb);
- if (control)
- memcpy(&status.control, control, sizeof(*control));
- kfree(control);
+ info = IEEE80211_SKB_CB(skb);
+ memset(&info->status, 0, sizeof(info->status));
- if (!(status.control.flags & IEEE80211_TXCTL_NO_ACK)) {
+ if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
if (flags & RTL8180_TX_DESC_FLAG_TX_OK)
- status.flags = IEEE80211_TX_STATUS_ACK;
+ info->flags |= IEEE80211_TX_STAT_ACK;
else
- status.excessive_retries = 1;
+ info->status.excessive_retries = 1;
}
- status.retry_count = flags & 0xFF;
+ info->status.retry_count = flags & 0xFF;
- ieee80211_tx_status_irqsafe(dev, skb, &status);
+ ieee80211_tx_status_irqsafe(dev, skb);
if (ring->entries - skb_queue_len(&ring->queue) == 2)
ieee80211_wake_queue(dev, prio);
}
return IRQ_HANDLED;
}
-static int rtl8180_tx(struct ieee80211_hw *dev, struct sk_buff *skb,
- struct ieee80211_tx_control *control)
+static int rtl8180_tx(struct ieee80211_hw *dev, struct sk_buff *skb)
{
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct rtl8180_priv *priv = dev->priv;
struct rtl8180_tx_ring *ring;
struct rtl8180_tx_desc *entry;
u16 plcp_len = 0;
__le16 rts_duration = 0;
- prio = control->queue;
+ prio = skb_get_queue_mapping(skb);
ring = &priv->tx_ring[prio];
mapping = pci_map_single(priv->pdev, skb->data,
skb->len, PCI_DMA_TODEVICE);
tx_flags = RTL8180_TX_DESC_FLAG_OWN | RTL8180_TX_DESC_FLAG_FS |
- RTL8180_TX_DESC_FLAG_LS | (control->tx_rate << 24) |
- (control->rts_cts_rate << 19) | skb->len;
+ RTL8180_TX_DESC_FLAG_LS |
+ (ieee80211_get_tx_rate(dev, info)->hw_value << 24) |
+ skb->len;
if (priv->r8185)
tx_flags |= RTL8180_TX_DESC_FLAG_DMA |
RTL8180_TX_DESC_FLAG_NO_ENC;
- if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS)
+ if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) {
tx_flags |= RTL8180_TX_DESC_FLAG_RTS;
- else if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT)
+ tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
+ } else if (info->flags & IEEE80211_TX_CTL_USE_CTS_PROTECT) {
tx_flags |= RTL8180_TX_DESC_FLAG_CTS;
+ tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
+ }
- *((struct ieee80211_tx_control **) skb->cb) =
- kmemdup(control, sizeof(*control), GFP_ATOMIC);
-
- if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS)
+ if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS)
rts_duration = ieee80211_rts_duration(dev, priv->vif, skb->len,
- control);
+ info);
if (!priv->r8185) {
unsigned int remainder;
plcp_len = DIV_ROUND_UP(16 * (skb->len + 4),
- (control->rate->rate * 2) / 10);
+ (ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10);
remainder = (16 * (skb->len + 4)) %
- ((control->rate->rate * 2) / 10);
+ ((ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10);
if (remainder > 0 && remainder <= 6)
plcp_len |= 1 << 15;
}
entry->plcp_len = cpu_to_le16(plcp_len);
entry->tx_buf = cpu_to_le32(mapping);
entry->frame_len = cpu_to_le32(skb->len);
- entry->flags2 = control->alt_retry_rate != -1 ?
- control->alt_retry_rate << 4 : 0;
- entry->retry_limit = control->retry_limit;
+ entry->flags2 = info->control.alt_retry_rate_idx >= 0 ?
+ ieee80211_get_alt_retry_rate(dev, info)->bitrate << 4 : 0;
+ entry->retry_limit = info->control.retry_limit;
entry->flags = cpu_to_le32(tx_flags);
__skb_queue_tail(&ring->queue, skb);
if (ring->entries - skb_queue_len(&ring->queue) < 2)
- ieee80211_stop_queue(dev, control->queue);
+ ieee80211_stop_queue(dev, skb_get_queue_mapping(skb));
spin_unlock_irqrestore(&priv->lock, flags);
rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, (1 << (prio + 4)));
pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf),
skb->len, PCI_DMA_TODEVICE);
- kfree(*((struct ieee80211_tx_control **) skb->cb));
kfree_skb(skb);
ring->idx = (ring->idx + 1) % ring->entries;
}
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->MAC[0],
- cpu_to_le32(*(u32 *)conf->mac_addr));
+ le32_to_cpu(*(__le32 *)conf->mac_addr));
rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->MAC[4],
- cpu_to_le16(*(u16 *)(conf->mac_addr + 4)));
+ le16_to_cpu(*(__le16 *)(conf->mac_addr + 4)));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
return 0;
goto err_free_dev;
}
+ BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels));
+ BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates));
+
memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
- priv->modes[0].mode = MODE_IEEE80211G;
- priv->modes[0].num_rates = ARRAY_SIZE(rtl818x_rates);
- priv->modes[0].rates = priv->rates;
- priv->modes[0].num_channels = ARRAY_SIZE(rtl818x_channels);
- priv->modes[0].channels = priv->channels;
- priv->modes[1].mode = MODE_IEEE80211B;
- priv->modes[1].num_rates = 4;
- priv->modes[1].rates = priv->rates;
- priv->modes[1].num_channels = ARRAY_SIZE(rtl818x_channels);
- priv->modes[1].channels = priv->channels;
- priv->mode = IEEE80211_IF_TYPE_INVALID;
+
+ priv->band.band = IEEE80211_BAND_2GHZ;
+ priv->band.channels = priv->channels;
+ priv->band.n_channels = ARRAY_SIZE(rtl818x_channels);
+ priv->band.bitrates = priv->rates;
+ priv->band.n_bitrates = 4;
+ dev->wiphy->bands[IEEE80211_BAND_2GHZ] = &priv->band;
+
dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
- IEEE80211_HW_RX_INCLUDES_FCS;
+ IEEE80211_HW_RX_INCLUDES_FCS |
+ IEEE80211_HW_SIGNAL_UNSPEC;
dev->queues = 1;
- dev->max_rssi = 65;
+ dev->max_signal = 65;
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
reg &= RTL818X_TX_CONF_HWVER_MASK;
priv->r8185 = reg & RTL818X_TX_CONF_R8185_ABC;
if (priv->r8185) {
- if ((err = ieee80211_register_hwmode(dev, &priv->modes[0])))
- goto err_iounmap;
-
+ priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates);
pci_try_set_mwi(pdev);
}
- if ((err = ieee80211_register_hwmode(dev, &priv->modes[1])))
- goto err_iounmap;
-
eeprom.data = dev;
eeprom.register_read = rtl8180_eeprom_register_read;
eeprom.register_write = rtl8180_eeprom_register_write;
for (i = 0; i < 14; i += 2) {
u16 txpwr;
eeprom_93cx6_read(&eeprom, 0x10 + (i >> 1), &txpwr);
- priv->channels[i].val = txpwr & 0xFF;
- priv->channels[i + 1].val = txpwr >> 8;
+ priv->channels[i].hw_value = txpwr & 0xFF;
+ priv->channels[i + 1].hw_value = txpwr >> 8;
}
/* OFDM TX power */
for (i = 0; i < 14; i += 2) {
u16 txpwr;
eeprom_93cx6_read(&eeprom, 0x20 + (i >> 1), &txpwr);
- priv->channels[i].val |= (txpwr & 0xFF) << 8;
- priv->channels[i + 1].val |= txpwr & 0xFF00;
+ priv->channels[i].hw_value |= (txpwr & 0xFF) << 8;
+ priv->channels[i + 1].hw_value |= txpwr & 0xFF00;
}
}