debug_info_t *cio_debug_trace_id;
debug_info_t *cio_debug_crw_id;
-int cio_show_msg;
-
-static int __init
-cio_setup (char *parm)
-{
- if (!strcmp (parm, "yes"))
- cio_show_msg = 1;
- else if (!strcmp (parm, "no"))
- cio_show_msg = 0;
- else
- printk(KERN_ERR "cio: cio_setup: "
- "invalid cio_msg parameter '%s'", parm);
- return 1;
-}
-
-__setup ("cio_msg=", cio_setup);
-
/*
* Function: cio_debug_init
* Initializes three debug logs for common I/O:
stsch (sch->schid, &sch->schib);
- CIO_MSG_EVENT(0, "cio_start: 'not oper' status for "
+ CIO_MSG_EVENT(2, "cio_start: 'not oper' status for "
"subchannel 0.%x.%04x!\n", sch->schid.ssid,
sch->schid.sch_no);
sprintf(dbf_text, "no%s", sch->dev.bus_id);
/*
* Enable subchannel.
*/
-int cio_enable_subchannel(struct subchannel *sch, unsigned int isc,
- u32 intparm)
+int cio_enable_subchannel(struct subchannel *sch, u32 intparm)
{
char dbf_txt[15];
int ccode;
for (retry = 5, ret = 0; retry > 0; retry--) {
sch->schib.pmcw.ena = 1;
- sch->schib.pmcw.isc = isc;
+ sch->schib.pmcw.isc = sch->isc;
sch->schib.pmcw.intparm = intparm;
ret = cio_modify(sch);
if (ret == -ENODEV)
* ... just being curious we check for non I/O subchannels
*/
if (sch->st != 0) {
- CIO_DEBUG(KERN_INFO, 0,
- "Subchannel 0.%x.%04x reports "
- "non-I/O subchannel type %04X\n",
- sch->schid.ssid, sch->schid.sch_no, sch->st);
+ CIO_MSG_EVENT(4, "Subchannel 0.%x.%04x reports "
+ "non-I/O subchannel type %04X\n",
+ sch->schid.ssid, sch->schid.sch_no, sch->st);
/* We stop here for non-io subchannels. */
err = sch->st;
goto out;
* This device must not be known to Linux. So we simply
* say that there is no device and return ENODEV.
*/
- CIO_MSG_EVENT(4, "Blacklisted device detected "
+ CIO_MSG_EVENT(6, "Blacklisted device detected "
"at devno %04X, subchannel set %x\n",
sch->schib.pmcw.dev, sch->schid.ssid);
err = -ENODEV;
goto out;
}
- if (cio_is_console(sch->schid))
+ if (cio_is_console(sch->schid)) {
sch->opm = 0xff;
- else
+ sch->isc = 1;
+ } else {
sch->opm = chp_get_sch_opm(sch);
+ sch->isc = 3;
+ }
sch->lpm = sch->schib.pmcw.pam & sch->opm;
- CIO_DEBUG(KERN_INFO, 0,
- "Detected device %04x on subchannel 0.%x.%04X"
- " - PIM = %02X, PAM = %02X, POM = %02X\n",
- sch->schib.pmcw.dev, sch->schid.ssid,
- sch->schid.sch_no, sch->schib.pmcw.pim,
- sch->schib.pmcw.pam, sch->schib.pmcw.pom);
+ CIO_MSG_EVENT(6, "Detected device %04x on subchannel 0.%x.%04X "
+ "- PIM = %02X, PAM = %02X, POM = %02X\n",
+ sch->schib.pmcw.dev, sch->schid.ssid,
+ sch->schid.sch_no, sch->schib.pmcw.pim,
+ sch->schib.pmcw.pam, sch->schib.pmcw.pom);
/*
* We now have to initially ...
- * ... set "interruption subclass"
* ... enable "concurrent sense"
* ... enable "multipath mode" if more than one
* CHPID is available. This is done regardless
* whether multiple paths are available for us.
*/
- sch->schib.pmcw.isc = 3; /* could be smth. else */
sch->schib.pmcw.csense = 1; /* concurrent sense */
sch->schib.pmcw.ena = 0;
if ((sch->lpm & (sch->lpm - 1)) != 0)
if (!console_subchannel_in_use)
return;
- /* disable all but isc 7 (console device) */
+ /* disable all but isc 1 (console device) */
__ctl_store (save_cr6, 6, 6);
- cr6 = 0x01000000;
+ cr6 = 0x40000000;
__ctl_load (cr6, 6, 6);
do {
}
/*
- * enable console I/O-interrupt subclass 7
+ * enable console I/O-interrupt subclass 1
*/
- ctl_set_bit(6, 24);
- console_subchannel.schib.pmcw.isc = 7;
+ ctl_set_bit(6, 30);
+ console_subchannel.isc = 1;
+ console_subchannel.schib.pmcw.isc = 1;
console_subchannel.schib.pmcw.intparm =
(u32)(addr_t)&console_subchannel;
ret = cio_modify(&console_subchannel);