[netdrvr forcedeth] remove superfluous rx engine stop/start

[linux-2.6-omap-h63xx.git] / drivers / scsi / Kconfig

diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 3ee9b8b33be0deeeea353b4e3b46860b6d9a990b..afeca325b4dc8a18884b10544ff53f6537123343 100644 (file)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -229,7 +229,7 @@ config SCSI_FC_ATTRS
 
 config SCSI_ISCSI_ATTRS
        tristate "iSCSI Transport Attributes"
-       depends on SCSI
+       depends on SCSI && NET
        help
          If you wish to export transport-specific information about
          each attached iSCSI device to sysfs, say Y.
@@ -247,6 +247,30 @@ endmenu
 menu "SCSI low-level drivers"
        depends on SCSI!=n
 
+config ISCSI_TCP
+       tristate "iSCSI Initiator over TCP/IP"
+       depends on SCSI && INET
+       select CRYPTO
+       select CRYPTO_MD5
+       select CRYPTO_CRC32C
+       select SCSI_ISCSI_ATTRS
+       help
+        The iSCSI Driver provides a host with the ability to access storage
+        through an IP network. The driver uses the iSCSI protocol to transport
+        SCSI requests and responses over a TCP/IP network between the host
+        (the "initiator") and "targets".  Architecturally, the iSCSI driver
+        combines with the host's TCP/IP stack, network drivers, and Network
+        Interface Card (NIC) to provide the same functions as a SCSI or a
+        Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA).
+
+        To compile this driver as a module, choose M here: the
+        module will be called iscsi_tcp.
+
+        The userspace component needed to initialize the driver, documentation,
+        and sample configuration files can be found here:
+
+        http://linux-iscsi.sf.net
+
 config SGIWD93_SCSI
        tristate "SGI WD93C93 SCSI Driver"
        depends on SGI_IP22 && SCSI
@@ -489,11 +513,11 @@ config SCSI_SATA_NV
 
          If unsure, say N.
 
-config SCSI_SATA_PROMISE
-       tristate "Promise SATA TX2/TX4 support"
+config SCSI_PDC_ADMA
+       tristate "Pacific Digital ADMA support"
        depends on SCSI_SATA && PCI
        help
-         This option enables support for Promise Serial ATA TX2/TX4.
+         This option enables support for Pacific Digital ADMA controllers
 
          If unsure, say N.
 
@@ -505,6 +529,14 @@ config SCSI_SATA_QSTOR
 
          If unsure, say N.
 
+config SCSI_SATA_PROMISE
+       tristate "Promise SATA TX2/TX4 support"
+       depends on SCSI_SATA && PCI
+       help
+         This option enables support for Promise Serial ATA TX2/TX4.
+
+         If unsure, say N.
+
 config SCSI_SATA_SX4
        tristate "Promise SATA SX4 support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
@@ -521,6 +553,14 @@ config SCSI_SATA_SIL
 
          If unsure, say N.
 
+config SCSI_SATA_SIL24
+       tristate "Silicon Image 3124/3132 SATA support"
+       depends on SCSI_SATA && PCI && EXPERIMENTAL
+       help
+         This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+         If unsure, say N.
+
 config SCSI_SATA_SIS
        tristate "SiS 964/180 SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
@@ -580,19 +620,6 @@ config SCSI_OMIT_FLASHPOINT
          substantial, so users of MultiMaster Host Adapters may wish to omit
          it.
 
-#
-# This is marked broken because it uses over 4kB of stack in
-# just two routines:
-#     2076  CpqTsProcessIMQEntry
-#     2052  PeekIMQEntry
-#
-config SCSI_CPQFCTS
-       tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support"
-       depends on PCI && SCSI && BROKEN
-       help
-         Say Y here to compile in support for the Compaq StorageWorks Fibre
-         Channel 64-bit/66Mhz Host Bus Adapter.
-
 config SCSI_DMX3191D
        tristate "DMX3191D SCSI support"
        depends on PCI && SCSI