uint32_t response_q_address[2];
uint32_t prio_request_q_address[2];
- uint8_t reserved_2[8];
+ uint16_t msix;
+ uint8_t reserved_2[6];
uint16_t atio_q_inpointer;
uint16_t atio_q_length;
* BIT 17-31 = Reserved
*/
uint32_t firmware_options_3;
-
- uint8_t reserved_3[24];
+ uint16_t qos;
+ uint16_t rid;
+ uint8_t reserved_3[20];
};
/*
uint32_t handle_to_abort; /* System handle to abort. */
- uint8_t reserved_1[32];
+ uint16_t req_que_no;
+ uint8_t reserved_1[30];
uint8_t port_id[3]; /* PortID of destination port. */
uint8_t vp_index;
struct qla_flt_location {
uint8_t sig[4];
- uint32_t start_lo;
- uint32_t start_hi;
- uint16_t unused;
+ uint16_t start_lo;
+ uint16_t start_hi;
+ uint8_t version;
+ uint8_t unused[5];
uint16_t checksum;
};
struct qla_npiv_entry {
uint16_t flags;
uint16_t vf_id;
- uint16_t qos;
+ uint8_t q_qos;
+ uint8_t f_qos;
uint16_t unused1;
uint8_t port_name[WWN_SIZE];
uint8_t node_name[WWN_SIZE];
uint32_t reserved[12];
};
+
+/* 81XX Support **************************************************************/
+
+#define MBA_DCBX_START 0x8016
+#define MBA_DCBX_COMPLETE 0x8030
+#define MBA_FCF_CONF_ERR 0x8031
+#define MBA_DCBX_PARAM_UPDATE 0x8032
+#define MBA_IDC_COMPLETE 0x8100
+#define MBA_IDC_NOTIFY 0x8101
+#define MBA_IDC_TIME_EXT 0x8102
+
+#define MBC_IDC_ACK 0x101
+
+struct nvram_81xx {
+ /* NVRAM header. */
+ uint8_t id[4];
+ uint16_t nvram_version;
+ uint16_t reserved_0;
+
+ /* Firmware Initialization Control Block. */
+ uint16_t version;
+ uint16_t reserved_1;
+ uint16_t frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+ uint16_t reserved_2;
+
+ uint8_t port_name[WWN_SIZE];
+ uint8_t node_name[WWN_SIZE];
+
+ uint16_t login_retry_count;
+ uint16_t reserved_3;
+ uint16_t interrupt_delay_timer;
+ uint16_t login_timeout;
+
+ uint32_t firmware_options_1;
+ uint32_t firmware_options_2;
+ uint32_t firmware_options_3;
+
+ uint16_t reserved_4[4];
+
+ /* Offset 64. */
+ uint8_t enode_mac[6];
+ uint16_t reserved_5[5];
+
+ /* Offset 80. */
+ uint16_t reserved_6[24];
+
+ /* Offset 128. */
+ uint16_t reserved_7[64];
+
+ /*
+ * BIT 0 = Enable spinup delay
+ * BIT 1 = Disable BIOS
+ * BIT 2 = Enable Memory Map BIOS
+ * BIT 3 = Enable Selectable Boot
+ * BIT 4 = Disable RISC code load
+ * BIT 5 = Disable Serdes
+ * BIT 6 = Opt boot mode
+ * BIT 7 = Interrupt enable
+ *
+ * BIT 8 = EV Control enable
+ * BIT 9 = Enable lip reset
+ * BIT 10 = Enable lip full login
+ * BIT 11 = Enable target reset
+ * BIT 12 = Stop firmware
+ * BIT 13 = Enable nodename option
+ * BIT 14 = Default WWPN valid
+ * BIT 15 = Enable alternate WWN
+ *
+ * BIT 16 = CLP LUN string
+ * BIT 17 = CLP Target string
+ * BIT 18 = CLP BIOS enable string
+ * BIT 19 = CLP Serdes string
+ * BIT 20 = CLP WWPN string
+ * BIT 21 = CLP WWNN string
+ * BIT 22 =
+ * BIT 23 =
+ * BIT 24 = Keep WWPN
+ * BIT 25 = Temp WWPN
+ * BIT 26-31 =
+ */
+ uint32_t host_p;
+
+ uint8_t alternate_port_name[WWN_SIZE];
+ uint8_t alternate_node_name[WWN_SIZE];
+
+ uint8_t boot_port_name[WWN_SIZE];
+ uint16_t boot_lun_number;
+ uint16_t reserved_8;
+
+ uint8_t alt1_boot_port_name[WWN_SIZE];
+ uint16_t alt1_boot_lun_number;
+ uint16_t reserved_9;
+
+ uint8_t alt2_boot_port_name[WWN_SIZE];
+ uint16_t alt2_boot_lun_number;
+ uint16_t reserved_10;
+
+ uint8_t alt3_boot_port_name[WWN_SIZE];
+ uint16_t alt3_boot_lun_number;
+ uint16_t reserved_11;
+
+ /*
+ * BIT 0 = Selective Login
+ * BIT 1 = Alt-Boot Enable
+ * BIT 2 = Reserved
+ * BIT 3 = Boot Order List
+ * BIT 4 = Reserved
+ * BIT 5 = Selective LUN
+ * BIT 6 = Reserved
+ * BIT 7-31 =
+ */
+ uint32_t efi_parameters;
+
+ uint8_t reset_delay;
+ uint8_t reserved_12;
+ uint16_t reserved_13;
+
+ uint16_t boot_id_number;
+ uint16_t reserved_14;
+
+ uint16_t max_luns_per_target;
+ uint16_t reserved_15;
+
+ uint16_t port_down_retry_count;
+ uint16_t link_down_timeout;
+
+ /* FCode parameters. */
+ uint16_t fcode_parameter;
+
+ uint16_t reserved_16[3];
+
+ /* Offset 352. */
+ uint8_t reserved_17[4];
+ uint16_t reserved_18[5];
+ uint8_t reserved_19[2];
+ uint16_t reserved_20[8];
+
+ /* Offset 384. */
+ uint8_t reserved_21[16];
+ uint16_t reserved_22[8];
+
+ /* Offset 416. */
+ uint16_t reserved_23[32];
+
+ /* Offset 480. */
+ uint8_t model_name[16];
+
+ /* Offset 496. */
+ uint16_t feature_mask_l;
+ uint16_t feature_mask_h;
+ uint16_t reserved_24[2];
+
+ uint16_t subsystem_vendor_id;
+ uint16_t subsystem_device_id;
+
+ uint32_t checksum;
+};
+
+/*
+ * ISP Initialization Control Block.
+ * Little endian except where noted.
+ */
+#define ICB_VERSION 1
+struct init_cb_81xx {
+ uint16_t version;
+ uint16_t reserved_1;
+
+ uint16_t frame_payload_size;
+ uint16_t execution_throttle;
+ uint16_t exchange_count;
+
+ uint16_t reserved_2;
+
+ uint8_t port_name[WWN_SIZE]; /* Big endian. */
+ uint8_t node_name[WWN_SIZE]; /* Big endian. */
+
+ uint16_t response_q_inpointer;
+ uint16_t request_q_outpointer;
+
+ uint16_t login_retry_count;
+
+ uint16_t prio_request_q_outpointer;
+
+ uint16_t response_q_length;
+ uint16_t request_q_length;
+
+ uint16_t reserved_3;
+
+ uint16_t prio_request_q_length;
+
+ uint32_t request_q_address[2];
+ uint32_t response_q_address[2];
+ uint32_t prio_request_q_address[2];
+
+ uint8_t reserved_4[8];
+
+ uint16_t atio_q_inpointer;
+ uint16_t atio_q_length;
+ uint32_t atio_q_address[2];
+
+ uint16_t interrupt_delay_timer; /* 100us increments. */
+ uint16_t login_timeout;
+
+ /*
+ * BIT 0-3 = Reserved
+ * BIT 4 = Enable Target Mode
+ * BIT 5 = Disable Initiator Mode
+ * BIT 6 = Reserved
+ * BIT 7 = Reserved
+ *
+ * BIT 8-13 = Reserved
+ * BIT 14 = Node Name Option
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_1;
+
+ /*
+ * BIT 0 = Operation Mode bit 0
+ * BIT 1 = Operation Mode bit 1
+ * BIT 2 = Operation Mode bit 2
+ * BIT 3 = Operation Mode bit 3
+ * BIT 4-7 = Reserved
+ *
+ * BIT 8 = Enable Class 2
+ * BIT 9 = Enable ACK0
+ * BIT 10 = Reserved
+ * BIT 11 = Enable FC-SP Security
+ * BIT 12 = FC Tape Enable
+ * BIT 13 = Reserved
+ * BIT 14 = Enable Target PRLI Control
+ * BIT 15-31 = Reserved
+ */
+ uint32_t firmware_options_2;
+
+ /*
+ * BIT 0-3 = Reserved
+ * BIT 4 = FCP RSP Payload bit 0
+ * BIT 5 = FCP RSP Payload bit 1
+ * BIT 6 = Enable Receive Out-of-Order data frame handling
+ * BIT 7 = Reserved
+ *
+ * BIT 8 = Reserved
+ * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling
+ * BIT 10-16 = Reserved
+ * BIT 17 = Enable multiple FCFs
+ * BIT 18-20 = MAC addressing mode
+ * BIT 21-25 = Ethernet data rate
+ * BIT 26 = Enable ethernet header rx IOCB for ATIO q
+ * BIT 27 = Enable ethernet header rx IOCB for response q
+ * BIT 28 = SPMA selection bit 0
+ * BIT 28 = SPMA selection bit 1
+ * BIT 30-31 = Reserved
+ */
+ uint32_t firmware_options_3;
+
+ uint8_t reserved_5[8];
+
+ uint8_t enode_mac[6];
+
+ uint8_t reserved_6[10];
+};
+
+struct mid_init_cb_81xx {
+ struct init_cb_81xx init_cb;
+
+ uint16_t count;
+ uint16_t options;
+
+ struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC];
+};
+
+#define FARX_ACCESS_FLASH_CONF_81XX 0x7FFD0000
+#define FARX_ACCESS_FLASH_DATA_81XX 0x7F800000
+
+/* 81XX Flash locations -- occupies second 2MB region. */
+#define FA_BOOT_CODE_ADDR_81 0x80000
+#define FA_RISC_CODE_ADDR_81 0xA0000
+#define FA_FW_AREA_ADDR_81 0xC0000
+#define FA_VPD_NVRAM_ADDR_81 0xD0000
+#define FA_FEATURE_ADDR_81 0xD4000
+#define FA_FLASH_DESCR_ADDR_81 0xD8000
+#define FA_FLASH_LAYOUT_ADDR_81 0xD8400
+#define FA_HW_EVENT0_ADDR_81 0xDC000
+#define FA_HW_EVENT1_ADDR_81 0xDC400
+#define FA_NPIV_CONF0_ADDR_81 0xD1000
+#define FA_NPIV_CONF1_ADDR_81 0xD2000
+
#endif
projects / linux-2.6-omap-h63xx.git / blobdiff