scsi_cmd[4] = 0x2a; /* size */
scsi_cmd[5] = 0;
scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE, result, 0x2a, NULL,
- SCSI_TIMEOUT, 3);
+ SCSI_TIMEOUT, 3, NULL);
}
/**
dev->type = &scsi_target_type;
starget->id = id;
starget->channel = channel;
+ starget->can_queue = 0;
INIT_LIST_HEAD(&starget->siblings);
INIT_LIST_HEAD(&starget->devices);
starget->state = STARGET_CREATED;
/* Each pass gets up to three chances to ignore Unit Attention */
for (count = 0; count < 3; ++count) {
+ int resid;
+
memset(scsi_cmd, 0, 6);
scsi_cmd[0] = INQUIRY;
scsi_cmd[4] = (unsigned char) try_inquiry_len;
result = scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE,
inq_result, try_inquiry_len, &sshdr,
- HZ / 2 + HZ * scsi_inq_timeout, 3);
+ HZ / 2 + HZ * scsi_inq_timeout, 3,
+ &resid);
SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO "scsi scan: INQUIRY %s "
"with code 0x%x\n",
(sshdr.ascq == 0))
continue;
}
+ } else {
+ /*
+ * if nothing was transferred, we try
+ * again. It's a workaround for some USB
+ * devices.
+ */
+ if (resid == try_inquiry_len)
+ continue;
}
break;
}
static int scsi_add_lun(struct scsi_device *sdev, unsigned char *inq_result,
int *bflags, int async)
{
+ int ret;
+
/*
* XXX do not save the inquiry, since it can change underneath us,
* save just vendor/model/rev.
/* set the device running here so that slave configure
* may do I/O */
- scsi_device_set_state(sdev, SDEV_RUNNING);
+ ret = scsi_device_set_state(sdev, SDEV_RUNNING);
+ if (ret) {
+ ret = scsi_device_set_state(sdev, SDEV_BLOCK);
+
+ if (ret) {
+ sdev_printk(KERN_ERR, sdev,
+ "in wrong state %s to complete scan\n",
+ scsi_device_state_name(sdev->sdev_state));
+ return SCSI_SCAN_NO_RESPONSE;
+ }
+ }
if (*bflags & BLIST_MS_192_BYTES_FOR_3F)
sdev->use_192_bytes_for_3f = 1;
transport_configure_device(&sdev->sdev_gendev);
if (sdev->host->hostt->slave_configure) {
- int ret = sdev->host->hostt->slave_configure(sdev);
+ ret = sdev->host->hostt->slave_configure(sdev);
if (ret) {
/*
* if LLDD reports slave not present, don't clutter
*/
sdev = scsi_device_lookup_by_target(starget, lun);
if (sdev) {
- if (rescan || sdev->sdev_state != SDEV_CREATED) {
+ if (rescan || !scsi_device_created(sdev)) {
SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO
"scsi scan: device exists on %s\n",
sdev->sdev_gendev.bus_id));
result = scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE,
lun_data, length, &sshdr,
- SCSI_TIMEOUT + 4 * HZ, 3);
+ SCSI_TIMEOUT + 4 * HZ, 3, NULL);
SCSI_LOG_SCAN_BUS(3, printk (KERN_INFO "scsi scan: REPORT LUNS"
" %s (try %d) result 0x%x\n", result
kfree(lun_data);
out:
scsi_device_put(sdev);
- if (sdev->sdev_state == SDEV_CREATED)
+ if (scsi_device_created(sdev))
/*
* the sdev we used didn't appear in the report luns scan
*/