#define DPRINT_CONFIG(_x...) ;
//#define DPRINT_CONFIG(_x...) printk _x
#define NOT_PROGRESS() ;
-//#define NOT_PROGRESS() printk("%s : fails %d\n", __FUNCTION__, __LINE__)
+//#define NOT_PROGRESS() printk("%s : fails %d\n", __func__, __LINE__)
/* number of characters we want to transmit to the lower level at a time */
#define MAX_CHARS 256
sbbr_h = &idd->vma->sbbr_h;
ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
DPRINT_CONFIG(("%s: ring_pci_addr 0x%p\n",
- __FUNCTION__, (void *)ring_pci_addr));
+ __func__, (void *)ring_pci_addr));
writel((unsigned int)((uint64_t) ring_pci_addr >> 32), sbbr_h);
writel((unsigned int)ring_pci_addr | BUF_SIZE_BIT, sbbr_l);
DPRINT_CONFIG(("%s: line %d baud %d byte_size %d stop %d parenb %d "
"parodd %d\n",
- __FUNCTION__, ((struct uart_port *)port->ip_port)->line,
+ __func__, ((struct uart_port *)port->ip_port)->line,
baud, byte_size, stop_bits, parenb, parodd));
if (set_baud(port, baud))
default:
case PROTO_RS232:
/* Clear the appropriate GIO pin */
- DPRINT_CONFIG(("%s: rs232\n", __FUNCTION__));
+ DPRINT_CONFIG(("%s: rs232\n", __func__));
writel(0, (&port->ip_idd->vma->gppr[0]
+ hooks->rs422_select_pin));
break;
case PROTO_RS422:
/* Set the appropriate GIO pin */
- DPRINT_CONFIG(("%s: rs422\n", __FUNCTION__));
+ DPRINT_CONFIG(("%s: rs422\n", __func__));
writel(1, (&port->ip_idd->vma->gppr[0]
+ hooks->rs422_select_pin));
break;
return;
info = the_port->info;
- tty = info->tty;
+ tty = info->port.tty;
if (uart_circ_empty(&info->xmit) || uart_tx_stopped(the_port)) {
/* Nothing to do or hw stopped */
}
baud = uart_get_baud_rate(the_port, new_termios, old_termios,
MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED);
- DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __FUNCTION__, baud,
+ DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __func__, baud,
the_port->line));
if (!the_port->fifosize)
the_port->ignore_status_mask = N_ALL_INPUT;
- info->tty->low_latency = 1;
+ info->port.tty->low_latency = 1;
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
the_port->ignore_status_mask &= ~(N_PARITY_ERROR
| N_FRAMING_ERROR);
- if (I_IGNBRK(info->tty)) {
+ if (I_IGNBRK(info->port.tty)) {
the_port->ignore_status_mask &= ~N_BREAK;
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
}
if (!(cflag & CREAD)) {
DPRINT_CONFIG(("%s : port 0x%p line %d cflag 0%o "
"config_port(baud %d data %d stop %d penable %d "
" parity %d), notification 0x%x\n",
- __FUNCTION__, (void *)port, the_port->line, cflag, baud,
+ __func__, (void *)port, the_port->line, cflag, baud,
new_data, new_stop, new_parity_enable, new_parity,
the_port->ignore_status_mask));
/* Make sure all the pointers are "good" ones */
if (!info)
return 0;
- if (!info->tty)
+ if (!info->port.tty)
return 0;
if (!(port->ip_flags & INPUT_ENABLE))
return 0;
spin_lock_irqsave(&the_port->lock, pflags);
- tty = info->tty;
+ tty = info->port.tty;
read_count = do_read(the_port, ch, MAX_CHARS);
if (read_count > 0) {
struct pci_dev *pdev = idd->pdev;
DPRINT_CONFIG(("%s: attach pdev 0x%p - card_ptr 0x%p\n",
- __FUNCTION__, pdev, (void *)card_ptr));
+ __func__, pdev, (void *)card_ptr));
if (!card_ptr)
return -ENODEV;
port->ip_port = the_port;
DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p [%d/%d]\n",
- __FUNCTION__, (void *)the_port, (void *)port,
+ __func__, (void *)the_port, (void *)port,
phys_port, ii));
/* membase, iobase and mapbase just need to be non-0 */
if (uart_add_one_port(&ioc3_uart, the_port) < 0) {
printk(KERN_WARNING
"%s: unable to add port %d bus %d\n",
- __FUNCTION__, the_port->line, pdev->bus->number);
+ __func__, the_port->line, pdev->bus->number);
} else {
DPRINT_CONFIG(("IOC3 serial port %d irq %d bus %d\n",
the_port->line, the_port->irq, pdev->bus->number));
struct ioc3_port *ports[PORTS_PER_CARD];
int phys_port;
- DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __FUNCTION__, is, idd));
+ DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, is, idd));
card_ptr = kzalloc(sizeof(struct ioc3_card), GFP_KERNEL);
if (!card_ptr) {
DPRINT_CONFIG(("%s : Port A ip_serial_regs 0x%p "
"ip_uart_regs 0x%p\n",
- __FUNCTION__,
+ __func__,
(void *)port->ip_serial_regs,
(void *)port->ip_uart_regs));
DPRINT_CONFIG(("%s : Port A ip_cpu_ringbuf 0x%p "
"ip_dma_ringbuf 0x%p, ip_inring 0x%p "
"ip_outring 0x%p\n",
- __FUNCTION__,
+ __func__,
(void *)port->ip_cpu_ringbuf,
(void *)port->ip_dma_ringbuf,
(void *)port->ip_inring,
DPRINT_CONFIG(("%s : Port B ip_serial_regs 0x%p "
"ip_uart_regs 0x%p\n",
- __FUNCTION__,
+ __func__,
(void *)port->ip_serial_regs,
(void *)port->ip_uart_regs));
DPRINT_CONFIG(("%s : Port B ip_cpu_ringbuf 0x%p "
"ip_dma_ringbuf 0x%p, ip_inring 0x%p "
"ip_outring 0x%p\n",
- __FUNCTION__,
+ __func__,
(void *)port->ip_cpu_ringbuf,
(void *)port->ip_dma_ringbuf,
(void *)port->ip_inring,
}
DPRINT_CONFIG(("%s : port %d [addr 0x%p] card_ptr 0x%p",
- __FUNCTION__,
+ __func__,
phys_port, (void *)port, (void *)card_ptr));
DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n",
(void *)port->ip_serial_regs,
DPRINT_CONFIG(("%s: phys_port %d port 0x%p inring 0x%p "
"outring 0x%p\n",
- __FUNCTION__,
+ __func__,
phys_port, (void *)port,
(void *)port->ip_inring,
(void *)port->ip_outring));
if ((ret = uart_register_driver(&ioc3_uart)) < 0) {
printk(KERN_WARNING
"%s: Couldn't register IOC3 uart serial driver\n",
- __FUNCTION__);
+ __func__);
return ret;
}
ret = ioc3_register_submodule(&ioc3uart_submodule);