config SPI_BFIN
tristate "SPI controller driver for ADI Blackfin5xx"
- depends on SPI_MASTER && BFIN
+ depends on SPI_MASTER && BLACKFIN
help
This is the SPI controller master driver for Blackfin 5xx processor.
Controller in master SPI mode.
config SPI_MPC83xx
- tristate "Freescale MPC83xx SPI controller"
- depends on SPI_MASTER && PPC_83xx && EXPERIMENTAL
+ tristate "Freescale MPC83xx/QUICC Engine SPI controller"
+ depends on SPI_MASTER && (PPC_83xx || QUICC_ENGINE) && EXPERIMENTAL
select SPI_BITBANG
help
- This enables using the Freescale MPC83xx SPI controller in master
- mode.
+ This enables using the Freescale MPC83xx and QUICC Engine SPI
+ controllers in master mode.
Note, this driver uniquely supports the SPI controller on the MPC83xx
- family of PowerPC processors. The MPC83xx uses a simple set of shift
- registers for data (opposed to the CPM based descriptor model).
+ family of PowerPC processors, plus processors with QUICC Engine
+ technology. This driver uses a simple set of shift registers for data
+ (opposed to the CPM based descriptor model).
config SPI_OMAP_UWIRE
tristate "OMAP1 MicroWire"
This driver can also be built as a module. If so, the module
will be called at25.
+config SPI_TSC2101
+ depends on SPI_MASTER
+ tristate "TSC2101 chip support"
+ ---help---
+ Say Y here if you want support for the TSC2101 chip.
+ At the moment it provides basic register read / write interface
+ as well as a way to enable the MCLK clock.
+
+config SPI_TSC2102
+ depends on SPI_MASTER
+ tristate "TSC2102 codec support"
+ ---help---
+ Say Y here if you want support for the TSC2102 chip. It
+ will be needed for the touchscreen driver on some boards.
+
+config SPI_TSC210X
+ depends on SPI_MASTER && EXPERIMENTAL
+ tristate "TI TSC210x (TSC2101/TSC2102) support"
+ help
+ Say Y here if you want support for the TSC210x chips. Some
+ boards use these for touchscreen and audio support.
+
+ These are members of a family of highly integrated PDA analog
+ interface circuit. They include a 12-bit ADC used for battery,
+ temperature, touchscreen, and other sensors. They also have
+ an audio DAC and amplifier, and in some models an audio ADC.
+ The audio support is highly chip-specific, but most of the
+ sensor support works the same.
+
+ Note that the device has to be present in the board's SPI
+ devices table for this driver to load. This driver doesn't
+ automatically enable touchscreen, sensors or audio
+ functionality - enable these in their respective menus.
+
+config SPI_TSC2301
+ tristate "TSC2301 driver"
+ depends on SPI_MASTER
+ help
+ Say Y here if you have a TSC2301 chip connected to an SPI
+ bus on your board.
+
+ The TSC2301 is a highly integrated PDA analog interface circuit.
+ It contains a complete 12-bit A/D resistive touch screen
+ converter (ADC) including drivers, touch pressure measurement
+ capability, keypad controller, and 8-bit D/A converter (DAC) output
+ for LCD contrast control.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc2301.
+
+config SPI_TSC2301_AUDIO
+ boolean "TSC2301 audio support"
+ depends on SPI_TSC2301 && SND
+ help
+ Say Y here for if you are using the audio features of TSC2301.
+
config SPI_SPIDEV
tristate "User mode SPI device driver support"
depends on SPI_MASTER && EXPERIMENTAL