# fully appropriate there, so it'd need some thought to do well.
#
menu "SPI support"
+ depends on HAS_IOMEM
config SPI
bool "SPI support"
This selects a driver for the Atmel SPI Controller, present on
many AT32 (AVR32) and AT91 (ARM) chips.
+config SPI_BFIN
+ tristate "SPI controller driver for ADI Blackfin5xx"
+ depends on SPI_MASTER && BLACKFIN
+ help
+ This is the SPI controller master driver for Blackfin 5xx processor.
+
+config SPI_AU1550
+ tristate "Au1550/Au12x0 SPI Controller"
+ depends on SPI_MASTER && (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ If you say yes to this option, support will be included for the
+ Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
+
+ This driver can also be built as a module. If so, the module
+ will be called au1550_spi.
+
config SPI_BITBANG
tristate "Bitbanging SPI master"
depends on SPI_MASTER && EXPERIMENTAL
This enables using the Freescale iMX SPI controller in master
mode.
+config SPI_LM70_LLP
+ tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
+ depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This driver supports the NS LM70 LLP Evaluation Board,
+ which interfaces to an LM70 temperature sensor using
+ a parallel port.
+
+config SPI_MPC52xx_PSC
+ tristate "Freescale MPC52xx PSC SPI controller"
+ depends on SPI_MASTER && PPC_MPC52xx && EXPERIMENTAL
+ help
+ This enables using the Freescale MPC52xx Programmable Serial
+ Controller in master SPI mode.
+
config SPI_MPC83xx
- tristate "Freescale MPC83xx SPI controller"
- depends on SPI_MASTER && PPC_83xx && EXPERIMENTAL
+ tristate "Freescale MPC83xx/QUICC Engine SPI controller"
+ depends on SPI_MASTER && (PPC_83xx || QUICC_ENGINE) && EXPERIMENTAL
select SPI_BITBANG
help
- This enables using the Freescale MPC83xx SPI controller in master
- mode.
+ This enables using the Freescale MPC83xx and QUICC Engine SPI
+ controllers in master mode.
Note, this driver uniquely supports the SPI controller on the MPC83xx
- family of PowerPC processors. The MPC83xx uses a simple set of shift
- registers for data (opposed to the CPM based descriptor model).
+ family of PowerPC processors, plus processors with QUICC Engine
+ technology. This driver uses a simple set of shift registers for data
+ (opposed to the CPM based descriptor model).
config SPI_OMAP_UWIRE
tristate "OMAP1 MicroWire"
help
This hooks up to the MicroWire controller on OMAP1 chips.
+config SPI_OMAP24XX
+ tristate "McSPI driver for OMAP24xx/OMAP34xx"
+ depends on SPI_MASTER && (ARCH_OMAP24XX || ARCH_OMAP34XX)
+ help
+ SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI
+ (McSPI) modules.
config SPI_PXA2XX
tristate "PXA2xx SSP SPI master"
depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
+ select PXA_SSP
help
This enables using a PXA2xx SSP port as a SPI master controller.
The driver can be configured to use any SSP port and additional
config SPI_S3C24XX
tristate "Samsung S3C24XX series SPI"
depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
+ select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs
config SPI_S3C24XX_GPIO
tristate "Samsung S3C24XX series SPI by GPIO"
- depends on SPI_MASTER && ARCH_S3C2410 && SPI_BITBANG && EXPERIMENTAL
+ depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL
+ select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs using
GPIO lines to provide the SPI bus. This can be used where
the inbuilt hardware cannot provide the transfer mode, or
where the board is using non hardware connected pins.
+
+config SPI_SH_SCI
+ tristate "SuperH SCI SPI controller"
+ depends on SPI_MASTER && SUPERH
+ select SPI_BITBANG
+ help
+ SPI driver for SuperH SCI blocks.
+
+config SPI_TXX9
+ tristate "Toshiba TXx9 SPI controller"
+ depends on SPI_MASTER && GENERIC_GPIO && CPU_TX49XX
+ help
+ SPI driver for Toshiba TXx9 MIPS SoCs
+
+config SPI_XILINX
+ tristate "Xilinx SPI controller"
+ depends on SPI_MASTER && XILINX_VIRTEX && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This exposes the SPI controller IP from the Xilinx EDK.
+
+ See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
+ Product Specification document (DS464) for hardware details.
+
#
# Add new SPI master controllers in alphabetical order above this line
#
This driver can also be built as a module. If so, the module
will be called at25.
+config SPI_SPIDEV
+ tristate "User mode SPI device driver support"
+ depends on SPI_MASTER && EXPERIMENTAL
+ help
+ This supports user mode SPI protocol drivers.
+
+ Note that this application programming interface is EXPERIMENTAL
+ and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
+
+config SPI_TLE62X0
+ tristate "Infineon TLE62X0 (for power switching)"
+ depends on SPI_MASTER && SYSFS
+ help
+ SPI driver for Infineon TLE62X0 series line driver chips,
+ such as the TLE6220, TLE6230 and TLE6240. This provides a
+ sysfs interface, with each line presented as a kind of GPIO
+ exposing both switch control and diagnostic feedback.
+
#
# Add new SPI protocol masters in alphabetical order above this line
#
-
# (slave support would go here)
endmenu # "SPI support"
projects / linux-2.6-omap-h63xx.git / blobdiff