struct ohci_hcd *ohci = hcd_to_ohci (hcd);
ohci->flags |= OHCI_QUIRK_ZFMICRO;
- ohci_dbg (ohci, "enabled Compaq ZFMicro chipset quirk\n");
+ ohci_dbg(ohci, "enabled Compaq ZFMicro chipset quirks\n");
return 0;
}
/* Check for NEC chip and apply quirk for allegedly lost interrupts.
*/
+
+static void ohci_quirk_nec_worker(struct work_struct *work)
+{
+ struct ohci_hcd *ohci = container_of(work, struct ohci_hcd, nec_work);
+ int status;
+
+ status = ohci_init(ohci);
+ if (status != 0) {
+ ohci_err(ohci, "Restarting NEC controller failed in %s, %d\n",
+ "ohci_init", status);
+ return;
+ }
+
+ status = ohci_restart(ohci);
+ if (status != 0)
+ ohci_err(ohci, "Restarting NEC controller failed in %s, %d\n",
+ "ohci_restart", status);
+}
+
static int ohci_quirk_nec(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
ohci->flags |= OHCI_QUIRK_NEC;
+ INIT_WORK(&ohci->nec_work, ohci_quirk_nec_worker);
ohci_dbg (ohci, "enabled NEC chipset lost interrupt quirk\n");
return 0;
return ret;
}
-#if defined(CONFIG_USB_PERSIST) && (defined(CONFIG_USB_EHCI_HCD) || \
- defined(CONFIG_USB_EHCI_HCD_MODULE))
-
-/* Following a power loss, we must prepare to regain control of the ports
- * we used to own. This means turning on the port power before ehci-hcd
- * tries to switch ownership.
- *
- * This isn't a 100% perfect solution. On most systems the OHCI controllers
- * lie at lower PCI addresses than the EHCI controller, so they will be
- * discovered (and hence resumed) first. But there is no guarantee things
- * will always work this way. If the EHCI controller is resumed first and
- * the OHCI ports are unpowered, then the handover will fail.
- */
-static void prepare_for_handover(struct usb_hcd *hcd)
-{
- struct ohci_hcd *ohci = hcd_to_ohci(hcd);
- int port;
-
- /* Here we "know" root ports should always stay powered */
- ohci_dbg(ohci, "powerup ports\n");
- for (port = 0; port < ohci->num_ports; port++)
- ohci_writel(ohci, RH_PS_PPS,
- &ohci->regs->roothub.portstatus[port]);
-
- /* Flush those writes */
- ohci_readl(ohci, &ohci->regs->control);
- msleep(20);
-}
-
-#else
-
-static inline void prepare_for_handover(struct usb_hcd *hcd)
-{ }
-
-#endif /* CONFIG_USB_PERSIST etc. */
-
#ifdef CONFIG_PM
static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
static int ohci_pci_resume (struct usb_hcd *hcd)
{
set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
-
- /* FIXME: we should try to detect loss of VBUS power here */
- prepare_for_handover(hcd);
-
+ ohci_finish_controller_resume(hcd);
return 0;
}
.shutdown = ohci_shutdown,
#ifdef CONFIG_PM
- /* these suspend/resume entries are for upstream PCI glue ONLY */
- .suspend = ohci_pci_suspend,
- .resume = ohci_pci_resume,
+ .pci_suspend = ohci_pci_suspend,
+ .pci_resume = ohci_pci_resume,
#endif
/*
*/
.hub_status_data = ohci_hub_status_data,
.hub_control = ohci_hub_control,
- .hub_irq_enable = ohci_rhsc_enable,
#ifdef CONFIG_PM
.bus_suspend = ohci_bus_suspend,
.bus_resume = ohci_bus_resume,