#include <linux/fb.h>
#include <linux/init.h>
#include <linux/delay.h>
+#include <linux/backlight.h>
#include <asm/arch/board.h>
#include <asm/arch/cpu.h>
#define ATMEL_LCDC_CVAL_DEFAULT 0xc8
#define ATMEL_LCDC_DMA_BURST_LEN 8
-#if defined(CONFIG_ARCH_AT91SAM9263)
+#if defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9)
#define ATMEL_LCDC_FIFO_SIZE 2048
#else
#define ATMEL_LCDC_FIFO_SIZE 512
}
#endif
+static const u32 contrast_ctr = ATMEL_LCDC_PS_DIV8
+ | ATMEL_LCDC_POL_POSITIVE
+ | ATMEL_LCDC_ENA_PWMENABLE;
+
+#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
+
+/* some bl->props field just changed */
+static int atmel_bl_update_status(struct backlight_device *bl)
+{
+ struct atmel_lcdfb_info *sinfo = bl_get_data(bl);
+ int power = sinfo->bl_power;
+ int brightness = bl->props.brightness;
+
+ /* REVISIT there may be a meaningful difference between
+ * fb_blank and power ... there seem to be some cases
+ * this doesn't handle correctly.
+ */
+ if (bl->props.fb_blank != sinfo->bl_power)
+ power = bl->props.fb_blank;
+ else if (bl->props.power != sinfo->bl_power)
+ power = bl->props.power;
+
+ if (brightness < 0 && power == FB_BLANK_UNBLANK)
+ brightness = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_VAL);
+ else if (power != FB_BLANK_UNBLANK)
+ brightness = 0;
+
+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, brightness);
+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR,
+ brightness ? contrast_ctr : 0);
+
+ bl->props.fb_blank = bl->props.power = sinfo->bl_power = power;
+
+ return 0;
+}
+
+static int atmel_bl_get_brightness(struct backlight_device *bl)
+{
+ struct atmel_lcdfb_info *sinfo = bl_get_data(bl);
+
+ return lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_VAL);
+}
+
+static struct backlight_ops atmel_lcdc_bl_ops = {
+ .update_status = atmel_bl_update_status,
+ .get_brightness = atmel_bl_get_brightness,
+};
+
+static void init_backlight(struct atmel_lcdfb_info *sinfo)
+{
+ struct backlight_device *bl;
+
+ sinfo->bl_power = FB_BLANK_UNBLANK;
+
+ if (sinfo->backlight)
+ return;
+
+ bl = backlight_device_register("backlight", &sinfo->pdev->dev,
+ sinfo, &atmel_lcdc_bl_ops);
+ if (IS_ERR(sinfo->backlight)) {
+ dev_err(&sinfo->pdev->dev, "error %ld on backlight register\n",
+ PTR_ERR(bl));
+ return;
+ }
+ sinfo->backlight = bl;
+
+ bl->props.power = FB_BLANK_UNBLANK;
+ bl->props.fb_blank = FB_BLANK_UNBLANK;
+ bl->props.max_brightness = 0xff;
+ bl->props.brightness = atmel_bl_get_brightness(bl);
+}
+
+static void exit_backlight(struct atmel_lcdfb_info *sinfo)
+{
+ if (sinfo->backlight)
+ backlight_device_unregister(sinfo->backlight);
+}
+
+#else
+
+static void init_backlight(struct atmel_lcdfb_info *sinfo)
+{
+ dev_warn(&sinfo->pdev->dev, "backlight control is not available\n");
+}
+
+static void exit_backlight(struct atmel_lcdfb_info *sinfo)
+{
+}
+
+#endif
+
+static void init_contrast(struct atmel_lcdfb_info *sinfo)
+{
+ /* have some default contrast/backlight settings */
+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
+
+ if (sinfo->lcdcon_is_backlight)
+ init_backlight(sinfo);
+}
+
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
.type = FB_TYPE_PACKED_PIXELS,
.accel = FB_ACCEL_NONE,
};
+static unsigned long compute_hozval(unsigned long xres, unsigned long lcdcon2)
+{
+ unsigned long value;
+
+ if (!(cpu_is_at91sam9261() || cpu_is_at32ap7000()))
+ return xres;
+
+ value = xres;
+ if ((lcdcon2 & ATMEL_LCDC_DISTYPE) != ATMEL_LCDC_DISTYPE_TFT) {
+ /* STN display */
+ if ((lcdcon2 & ATMEL_LCDC_DISTYPE) == ATMEL_LCDC_DISTYPE_STNCOLOR) {
+ value *= 3;
+ }
+ if ( (lcdcon2 & ATMEL_LCDC_IFWIDTH) == ATMEL_LCDC_IFWIDTH_4
+ || ( (lcdcon2 & ATMEL_LCDC_IFWIDTH) == ATMEL_LCDC_IFWIDTH_8
+ && (lcdcon2 & ATMEL_LCDC_SCANMOD) == ATMEL_LCDC_SCANMOD_DUAL ))
+ value = DIV_ROUND_UP(value, 4);
+ else
+ value = DIV_ROUND_UP(value, 8);
+ }
+
+ return value;
+}
static void atmel_lcdfb_update_dma(struct fb_info *info,
struct fb_var_screeninfo *var)
var->transp.offset = var->transp.length = 0;
var->xoffset = var->yoffset = 0;
+ /* Saturate vertical and horizontal timings at maximum values */
+ var->vsync_len = min_t(u32, var->vsync_len,
+ (ATMEL_LCDC_VPW >> ATMEL_LCDC_VPW_OFFSET) + 1);
+ var->upper_margin = min_t(u32, var->upper_margin,
+ ATMEL_LCDC_VBP >> ATMEL_LCDC_VBP_OFFSET);
+ var->lower_margin = min_t(u32, var->lower_margin,
+ ATMEL_LCDC_VFP);
+ var->right_margin = min_t(u32, var->right_margin,
+ (ATMEL_LCDC_HFP >> ATMEL_LCDC_HFP_OFFSET) + 1);
+ var->hsync_len = min_t(u32, var->hsync_len,
+ (ATMEL_LCDC_HPW >> ATMEL_LCDC_HPW_OFFSET) + 1);
+ var->left_margin = min_t(u32, var->left_margin,
+ ATMEL_LCDC_HBP + 1);
+
+ /* Some parameters can't be zero */
+ var->vsync_len = max_t(u32, var->vsync_len, 1);
+ var->right_margin = max_t(u32, var->right_margin, 1);
+ var->hsync_len = max_t(u32, var->hsync_len, 1);
+ var->left_margin = max_t(u32, var->left_margin, 1);
+
switch (var->bits_per_pixel) {
+ case 1:
case 2:
case 4:
case 8:
var->blue.offset = 10;
var->red.length = var->green.length = var->blue.length = 5;
break;
- case 24:
case 32:
+ var->transp.offset = 24;
+ var->transp.length = 8;
+ /* fall through */
+ case 24:
var->red.offset = 0;
var->green.offset = 8;
var->blue.offset = 16;
static int atmel_lcdfb_set_par(struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ unsigned long hozval_linesz;
unsigned long value;
unsigned long clk_value_khz;
+ unsigned long bits_per_line;
dev_dbg(info->device, "%s:\n", __func__);
dev_dbg(info->device, " * resolution: %ux%u (%ux%u virtual)\n",
/* Turn off the LCD controller and the DMA controller */
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON, sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
+ /* Wait for the LCDC core to become idle */
+ while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
+ msleep(10);
+
lcdc_writel(sinfo, ATMEL_LCDC_DMACON, 0);
- if (info->var.bits_per_pixel <= 8)
+ if (info->var.bits_per_pixel == 1)
+ info->fix.visual = FB_VISUAL_MONO01;
+ else if (info->var.bits_per_pixel <= 8)
info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
else
info->fix.visual = FB_VISUAL_TRUECOLOR;
- info->fix.line_length = info->var.xres_virtual * (info->var.bits_per_pixel / 8);
+ bits_per_line = info->var.xres_virtual * info->var.bits_per_pixel;
+ info->fix.line_length = DIV_ROUND_UP(bits_per_line, 8);
/* Re-initialize the DMA engine... */
dev_dbg(info->device, " * update DMA engine\n");
/* Set pixel clock */
clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
- value = clk_value_khz / PICOS2KHZ(info->var.pixclock);
-
- if (clk_value_khz % PICOS2KHZ(info->var.pixclock))
- value++;
+ value = DIV_ROUND_UP(clk_value_khz, PICOS2KHZ(info->var.pixclock));
value = (value / 2) - 1;
+ dev_dbg(info->device, " * programming CLKVAL = 0x%08lx\n", value);
if (value <= 0) {
dev_notice(info->device, "Bypassing pixel clock divider\n");
lcdc_writel(sinfo, ATMEL_LCDC_LCDCON1, ATMEL_LCDC_BYPASS);
- } else
+ } else {
lcdc_writel(sinfo, ATMEL_LCDC_LCDCON1, value << ATMEL_LCDC_CLKVAL_OFFSET);
+ info->var.pixclock = KHZ2PICOS(clk_value_khz / (2 * (value + 1)));
+ dev_dbg(info->device, " updated pixclk: %lu KHz\n",
+ PICOS2KHZ(info->var.pixclock));
+ }
+
/* Initialize control register 2 */
value = sinfo->default_lcdcon2;
dev_dbg(info->device, " * LCDTIM2 = %08lx\n", value);
lcdc_writel(sinfo, ATMEL_LCDC_TIM2, value);
+ /* Horizontal value (aka line size) */
+ hozval_linesz = compute_hozval(info->var.xres,
+ lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2));
+
/* Display size */
- value = (info->var.xres - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
+ value = (hozval_linesz - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
value |= info->var.yres - 1;
+ dev_dbg(info->device, " * LCDFRMCFG = %08lx\n", value);
lcdc_writel(sinfo, ATMEL_LCDC_LCDFRMCFG, value);
/* FIFO Threshold: Use formula from data sheet */
/* Disable all interrupts */
lcdc_writel(sinfo, ATMEL_LCDC_IDR, ~0UL);
- /* Set contrast */
- value = ATMEL_LCDC_PS_DIV8 | ATMEL_LCDC_POL_POSITIVE | ATMEL_LCDC_ENA_PWMENABLE;
- lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, value);
- lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
/* ...wait for DMA engine to become idle... */
while (lcdc_readl(sinfo, ATMEL_LCDC_DMACON) & ATMEL_LCDC_DMABUSY)
msleep(10);
ret = 0;
}
break;
+
+ case FB_VISUAL_MONO01:
+ if (regno < 2) {
+ val = (regno == 0) ? 0x00 : 0x1F;
+ lcdc_writel(sinfo, ATMEL_LCDC_LUT(regno), val);
+ ret = 0;
+ }
+ break;
+
}
return ret;
sinfo->default_monspecs = pdata_sinfo->default_monspecs;
sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
sinfo->guard_time = pdata_sinfo->guard_time;
+ sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
goto release_mem;
}
+ /* Initialize PWM for contrast or backlight ("off") */
+ init_contrast(sinfo);
+
/* interrupt */
ret = request_irq(sinfo->irq_base, atmel_lcdfb_interrupt, 0, pdev->name, info);
if (ret) {
unregister_irqs:
free_irq(sinfo->irq_base, info);
unmap_mmio:
+ exit_backlight(sinfo);
iounmap(sinfo->mmio);
release_mem:
release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
if (!sinfo)
return 0;
+ exit_backlight(sinfo);
if (sinfo->atmel_lcdfb_power_control)
sinfo->atmel_lcdfb_power_control(0);
unregister_framebuffer(info);
static struct platform_driver atmel_lcdfb_driver = {
.remove = __exit_p(atmel_lcdfb_remove),
+
+// FIXME need suspend, resume
+
.driver = {
.name = "atmel_lcdfb",
.owner = THIS_MODULE,
module_exit(atmel_lcdfb_exit);
MODULE_DESCRIPTION("AT91/AT32 LCD Controller framebuffer driver");
-MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre@rfo.atmel.com>");
+MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre@atmel.com>");
MODULE_LICENSE("GPL");
projects / linux-2.6-omap-h63xx.git / blobdiff