#ifndef __ASM_ARCH_MFP_H
#define __ASM_ARCH_MFP_H
-#define MFPR_BASE (0x40e10000)
-#define MFPR_SIZE (PAGE_SIZE)
-
#define mfp_to_gpio(m) ((m) % 128)
/* list of all the configurable MFP pins */
MFP_PIN_MAX,
};
-/*
- * Table that determines the low power modes outputs, with actual settings
- * used in parentheses for don't-care values. Except for the float output,
- * the configured driven and pulled levels match, so if there is a need for
- * non-LPM pulled output, the same configuration could probably be used.
- *
- * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
- * (bit 7) (bit 8) (bit 14d) (bit 13d)
- *
- * Drive 0 0 0 0 X (1) 0
- * Drive 1 0 1 X (1) 0 0
- * Pull hi (1) 1 X(1) 1 0 0
- * Pull lo (0) 1 X(0) 0 1 0
- * Z (float) 1 X(0) 0 0 0
- */
-#define MFP_LPM_DRIVE_LOW 0x8
-#define MFP_LPM_DRIVE_HIGH 0x6
-#define MFP_LPM_PULL_HIGH 0x7
-#define MFP_LPM_PULL_LOW 0x9
-#define MFP_LPM_FLOAT 0x1
-#define MFP_LPM_PULL_NEITHER 0x0
-
-/*
- * The pullup and pulldown state of the MFP pin is by default determined by
- * selected alternate function. In case some buggy devices need to override
- * this default behavior, pxa3xx_mfp_set_pull() can be invoked with one of
- * the following definition as the parameter.
- *
- * Definition pull_sel pullup_en pulldown_en
- * MFP_PULL_HIGH 1 1 0
- * MFP_PULL_LOW 1 0 1
- * MFP_PULL_BOTH 1 1 1
- * MFP_PULL_NONE 1 0 0
- * MFP_PULL_DEFAULT 0 X X
- *
- * NOTE: pxa3xx_mfp_set_pull() will modify the PULLUP_EN and PULLDOWN_EN
- * bits, which will cause potential conflicts with the low power mode
- * setting, device drivers should take care of this
- */
-#define MFP_PULL_BOTH (0x7u)
-#define MFP_PULL_HIGH (0x6u)
-#define MFP_PULL_LOW (0x5u)
-#define MFP_PULL_NONE (0x4u)
-#define MFP_PULL_DEFAULT (0x0u)
-
-#define MFP_AF0 (0)
-#define MFP_AF1 (1)
-#define MFP_AF2 (2)
-#define MFP_AF3 (3)
-#define MFP_AF4 (4)
-#define MFP_AF5 (5)
-#define MFP_AF6 (6)
-#define MFP_AF7 (7)
-
-#define MFP_DS01X (0)
-#define MFP_DS02X (1)
-#define MFP_DS03X (2)
-#define MFP_DS04X (3)
-#define MFP_DS06X (4)
-#define MFP_DS08X (5)
-#define MFP_DS10X (6)
-#define MFP_DS12X (7)
-
-#define MFP_EDGE_BOTH 0x3
-#define MFP_EDGE_RISE 0x2
-#define MFP_EDGE_FALL 0x1
-#define MFP_EDGE_NONE 0x0
-
-#define MFPR_AF_MASK 0x0007
-#define MFPR_DRV_MASK 0x1c00
-#define MFPR_RDH_MASK 0x0200
-#define MFPR_LPM_MASK 0xe180
-#define MFPR_PULL_MASK 0xe000
-#define MFPR_EDGE_MASK 0x0070
-
-#define MFPR_ALT_OFFSET 0
-#define MFPR_ERE_OFFSET 4
-#define MFPR_EFE_OFFSET 5
-#define MFPR_EC_OFFSET 6
-#define MFPR_SON_OFFSET 7
-#define MFPR_SD_OFFSET 8
-#define MFPR_SS_OFFSET 9
-#define MFPR_DRV_OFFSET 10
-#define MFPR_PD_OFFSET 13
-#define MFPR_PU_OFFSET 14
-#define MFPR_PS_OFFSET 15
-
-#define MFPR(af, drv, rdh, lpm, edge) \
- (((af) & 0x7) | (((drv) & 0x7) << 10) |\
- (((rdh) & 0x1) << 9) |\
- (((lpm) & 0x3) << 7) |\
- (((lpm) & 0x4) << 12)|\
- (((lpm) & 0x8) << 10)|\
- ((!(edge)) << 6) |\
- (((edge) & 0x1) << 5) |\
- (((edge) & 0x2) << 3))
-
/*
* a possible MFP configuration is represented by a 32-bit integer
- * bit 0..15 - MFPR value (16-bit)
- * bit 16..31 - mfp pin index (used to obtain the MFPR offset)
+ *
+ * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
+ * bit 10..12 - Alternate Function Selection
+ * bit 13..15 - Drive Strength
+ * bit 16..18 - Low Power Mode State
+ * bit 19..20 - Low Power Mode Edge Detection
+ * bit 21..22 - Run Mode Pull State
*
* to facilitate the definition, the following macros are provided
*
- * MFPR_DEFAULT - default MFPR value, with
+ * MFP_CFG_DEFAULT - default MFP configuration value, with
* alternate function = 0,
- * drive strength = fast 1mA (MFP_DS01X)
+ * drive strength = fast 3mA (MFP_DS03X)
* low power mode = default
- * release dalay hold = false (RDH bit)
* edge detection = none
*
* MFP_CFG - default MFPR value with alternate function
* low power mode
* MFP_CFG_X - default MFPR value with alternate function,
* pin drive strength and low power mode
- *
- * use
- *
- * MFP_CFG_PIN - to get the MFP pin index
- * MFP_CFG_VAL - to get the corresponding MFPR value
*/
-typedef uint32_t mfp_cfg_t;
-
-#define MFP_CFG_PIN(mfp_cfg) (((mfp_cfg) >> 16) & 0xffff)
-#define MFP_CFG_VAL(mfp_cfg) ((mfp_cfg) & 0xffff)
-
-/*
- * MFP register defaults to
- * drive strength fast 3mA (010'b)
- * edge detection logic disabled
- * alternate function 0
- */
-#define MFPR_DEFAULT (0x0840)
+typedef unsigned long mfp_cfg_t;
+
+#define MFP_PIN(x) ((x) & 0x3ff)
+
+#define MFP_AF0 (0x0 << 10)
+#define MFP_AF1 (0x1 << 10)
+#define MFP_AF2 (0x2 << 10)
+#define MFP_AF3 (0x3 << 10)
+#define MFP_AF4 (0x4 << 10)
+#define MFP_AF5 (0x5 << 10)
+#define MFP_AF6 (0x6 << 10)
+#define MFP_AF7 (0x7 << 10)
+#define MFP_AF_MASK (0x7 << 10)
+#define MFP_AF(x) (((x) >> 10) & 0x7)
+
+#define MFP_DS01X (0x0 << 13)
+#define MFP_DS02X (0x1 << 13)
+#define MFP_DS03X (0x2 << 13)
+#define MFP_DS04X (0x3 << 13)
+#define MFP_DS06X (0x4 << 13)
+#define MFP_DS08X (0x5 << 13)
+#define MFP_DS10X (0x6 << 13)
+#define MFP_DS13X (0x7 << 13)
+#define MFP_DS_MASK (0x7 << 13)
+#define MFP_DS(x) (((x) >> 13) & 0x7)
+
+#define MFP_LPM_INPUT (0x0 << 16)
+#define MFP_LPM_DRIVE_LOW (0x1 << 16)
+#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
+#define MFP_LPM_PULL_LOW (0x3 << 16)
+#define MFP_LPM_PULL_HIGH (0x4 << 16)
+#define MFP_LPM_FLOAT (0x5 << 16)
+#define MFP_LPM_STATE_MASK (0x7 << 16)
+#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
+
+#define MFP_LPM_EDGE_NONE (0x0 << 19)
+#define MFP_LPM_EDGE_RISE (0x1 << 19)
+#define MFP_LPM_EDGE_FALL (0x2 << 19)
+#define MFP_LPM_EDGE_BOTH (0x3 << 19)
+#define MFP_LPM_EDGE_MASK (0x3 << 19)
+#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
+
+#define MFP_PULL_NONE (0x0 << 21)
+#define MFP_PULL_LOW (0x1 << 21)
+#define MFP_PULL_HIGH (0x2 << 21)
+#define MFP_PULL_BOTH (0x3 << 21)
+#define MFP_PULL_MASK (0x3 << 21)
+#define MFP_PULL(x) (((x) >> 21) & 0x3)
+
+#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_INPUT |\
+ MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
#define MFP_CFG(pin, af) \
- ((MFP_PIN_##pin << 16) | MFPR_DEFAULT | (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
#define MFP_CFG_DRV(pin, af, drv) \
- ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_DRV_MASK) |\
- ((MFP_##drv) << 10) | (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
#define MFP_CFG_LPM(pin, af, lpm) \
- ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_LPM_MASK) |\
- (((MFP_LPM_##lpm) & 0x3) << 7) |\
- (((MFP_LPM_##lpm) & 0x4) << 12) |\
- (((MFP_LPM_##lpm) & 0x8) << 10) |\
- (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
#define MFP_CFG_X(pin, af, drv, lpm) \
- ((MFP_PIN_##pin << 16) |\
- (MFPR_DEFAULT & ~(MFPR_DRV_MASK | MFPR_LPM_MASK)) |\
- ((MFP_##drv) << 10) | (MFP_##af) |\
- (((MFP_LPM_##lpm) & 0x3) << 7) |\
- (((MFP_LPM_##lpm) & 0x4) << 12) |\
- (((MFP_LPM_##lpm) & 0x8) << 10))
-
-/*
- * each MFP pin will have a MFPR register, since the offset of the
- * register varies between processors, the processor specific code
- * should initialize the pin offsets by pxa3xx_mfp_init_addr()
- *
- * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
- * structure, which represents a range of MFP pins from "start" to
- * "end", with the offset begining at "offset", to define a single
- * pin, let "end" = -1
- *
- * use
- *
- * MFP_ADDR_X() to define a range of pins
- * MFP_ADDR() to define a single pin
- * MFP_ADDR_END to signal the end of pin offset definitions
- */
-struct pxa3xx_mfp_addr_map {
- unsigned int start;
- unsigned int end;
- unsigned long offset;
-};
-
-#define MFP_ADDR_X(start, end, offset) \
- { MFP_PIN_##start, MFP_PIN_##end, offset }
-
-#define MFP_ADDR(pin, offset) \
- { MFP_PIN_##pin, -1, offset }
-
-#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
-
-struct pxa3xx_mfp_pin {
- unsigned long mfpr_off; /* MFPRxx register offset */
- unsigned long mfpr_val; /* MFPRxx register value */
-};
-
-/*
- * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
- * to the MFPR register
- */
-unsigned long pxa3xx_mfp_read(int mfp);
-void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
-
-/*
- * pxa3xx_mfp_config - configure the MFPR registers
- *
- * used by board specific initialization code
- */
-void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num);
-
-/*
- * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
- * index and MFPR register offset
- *
- * used by processor specific code
- */
-void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
-void __init pxa3xx_init_mfp(void);
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
#endif /* __ASM_ARCH_MFP_H */
projects / linux-2.6-omap-h63xx.git / blobdiff