#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#ifdef CONFIG_PXA3xx
+#define GCR_CLKBPB (1 << 31) /* Internal clock enable */
+#endif
#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */
-#define USIR0_IR0 (1 << 0) /* Interrup request ep 0 */
-#define USIR0_IR1 (1 << 1) /* Interrup request ep 1 */
-#define USIR0_IR2 (1 << 2) /* Interrup request ep 2 */
-#define USIR0_IR3 (1 << 3) /* Interrup request ep 3 */
-#define USIR0_IR4 (1 << 4) /* Interrup request ep 4 */
-#define USIR0_IR5 (1 << 5) /* Interrup request ep 5 */
-#define USIR0_IR6 (1 << 6) /* Interrup request ep 6 */
-#define USIR0_IR7 (1 << 7) /* Interrup request ep 7 */
+#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */
+#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */
+#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */
+#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */
+#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */
+#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */
+#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */
+#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */
#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */
-#define USIR1_IR8 (1 << 0) /* Interrup request ep 8 */
-#define USIR1_IR9 (1 << 1) /* Interrup request ep 9 */
-#define USIR1_IR10 (1 << 2) /* Interrup request ep 10 */
-#define USIR1_IR11 (1 << 3) /* Interrup request ep 11 */
-#define USIR1_IR12 (1 << 4) /* Interrup request ep 12 */
-#define USIR1_IR13 (1 << 5) /* Interrup request ep 13 */
-#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
-#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
+#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */
+#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */
+#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */
+#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */
+#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */
+#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */
+#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */
+#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */
#elif defined(CONFIG_PXA27x)
#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */
#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */
-#define ICCR0_AME (1 << 7) /* Adress match enable */
+#define ICCR0_AME (1 << 7) /* Address match enable */
#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */
#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */
#define ICCR0_RXE (1 << 4) /* Receive enable */
* General Purpose I/O
*/
+#define GPIO0_BASE ((void __iomem *)io_p2v(0x40E00000))
+#define GPIO1_BASE ((void __iomem *)io_p2v(0x40E00004))
+#define GPIO2_BASE ((void __iomem *)io_p2v(0x40E00008))
+#define GPIO3_BASE ((void __iomem *)io_p2v(0x40E00100))
+
+#define GPLR_OFFSET 0x00
+#define GPDR_OFFSET 0x0C
+#define GPSR_OFFSET 0x18
+#define GPCR_OFFSET 0x24
+#define GRER_OFFSET 0x30
+#define GFER_OFFSET 0x3C
+#define GEDR_OFFSET 0x48
+
#define GPLR0 __REG(0x40E00000) /* GPIO Pin-Level Register GPIO<31:0> */
#define GPLR1 __REG(0x40E00004) /* GPIO Pin-Level Register GPIO<63:32> */
#define GPLR2 __REG(0x40E00008) /* GPIO Pin-Level Register GPIO<80:64> */
#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */
#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */
-
/*
- * SSP Serial Port Registers
- * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
- * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
+ * SSP Serial Port Registers - see include/asm-arm/arch-pxa/regs-ssp.h
*/
- /* Common PXA2xx bits first */
-#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
-#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
-#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
-#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */
-#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */
-#define SSCR0_National (0x2 << 4) /* National Microwire */
-#define SSCR0_ECS (1 << 6) /* External clock select */
-#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
-#if defined(CONFIG_PXA25x)
-#define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */
-#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */
-#elif defined(CONFIG_PXA27x)
-#define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */
-#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */
-#define SSCR0_EDSS (1 << 20) /* Extended data size select */
-#define SSCR0_NCS (1 << 21) /* Network clock select */
-#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */
-#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */
-#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */
-#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame [1..8] */
-#define SSCR0_ADC (1 << 30) /* Audio clock select */
-#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
-#endif
-
-#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
-#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
-#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
-#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */
-#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
-#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
-#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
-
-#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
-#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
-#define SSSR_BSY (1 << 4) /* SSP Busy */
-#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
-#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
-#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
-
-#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Interrupt Mask */
-#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run interrupt Mask */
-#define SSCR0_NCS (1 << 21) /* Network Clock Select */
-#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
-
-/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
-#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */
-#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
-#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
-#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
-#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
-#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
-#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
-#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
-#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
-#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
-#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
-#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
-#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
-#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
-#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
-#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
-#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
-#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
-
-#define SSSR_BCE (1 << 23) /* Bit Count Error */
-#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
-#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
-#define SSSR_EOC (1 << 20) /* End Of Chain */
-#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
-#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
-
-#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */
-#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */
-#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */
-#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */
-#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */
-#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */
-#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
-#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
-#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock Mode */
-
-#define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */
-#define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */
-#define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */
-
-#define SSCR0_P1 __REG(0x41000000) /* SSP Port 1 Control Register 0 */
-#define SSCR1_P1 __REG(0x41000004) /* SSP Port 1 Control Register 1 */
-#define SSSR_P1 __REG(0x41000008) /* SSP Port 1 Status Register */
-#define SSITR_P1 __REG(0x4100000C) /* SSP Port 1 Interrupt Test Register */
-#define SSDR_P1 __REG(0x41000010) /* (Write / Read) SSP Port 1 Data Write Register/SSP Data Read Register */
-
-/* Support existing PXA25x drivers */
-#define SSCR0 SSCR0_P1 /* SSP Control Register 0 */
-#define SSCR1 SSCR1_P1 /* SSP Control Register 1 */
-#define SSSR SSSR_P1 /* SSP Status Register */
-#define SSITR SSITR_P1 /* SSP Interrupt Test Register */
-#define SSDR SSDR_P1 /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
-/* PXA27x ports */
-#if defined (CONFIG_PXA27x)
-#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
-#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
-#define SSTSA_P1 __REG(0x41000030) /* SSP Port 1 Tx Timeslot Active */
-#define SSRSA_P1 __REG(0x41000034) /* SSP Port 1 Rx Timeslot Active */
-#define SSTSS_P1 __REG(0x41000038) /* SSP Port 1 Timeslot Status */
-#define SSACD_P1 __REG(0x4100003C) /* SSP Port 1 Audio Clock Divider */
-#define SSCR0_P2 __REG(0x41700000) /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2 __REG(0x41700004) /* SSP Port 2 Control Register 1 */
-#define SSSR_P2 __REG(0x41700008) /* SSP Port 2 Status Register */
-#define SSITR_P2 __REG(0x4170000C) /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2 __REG(0x41700010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2 __REG(0x41700028) /* SSP Port 2 Time Out Register */
-#define SSPSP_P2 __REG(0x4170002C) /* SSP Port 2 Programmable Serial Protocol */
-#define SSTSA_P2 __REG(0x41700030) /* SSP Port 2 Tx Timeslot Active */
-#define SSRSA_P2 __REG(0x41700034) /* SSP Port 2 Rx Timeslot Active */
-#define SSTSS_P2 __REG(0x41700038) /* SSP Port 2 Timeslot Status */
-#define SSACD_P2 __REG(0x4170003C) /* SSP Port 2 Audio Clock Divider */
-#define SSCR0_P3 __REG(0x41900000) /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3 __REG(0x41900004) /* SSP Port 3 Control Register 1 */
-#define SSSR_P3 __REG(0x41900008) /* SSP Port 3 Status Register */
-#define SSITR_P3 __REG(0x4190000C) /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3 __REG(0x41900010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3 __REG(0x41900028) /* SSP Port 3 Time Out Register */
-#define SSPSP_P3 __REG(0x4190002C) /* SSP Port 3 Programmable Serial Protocol */
-#define SSTSA_P3 __REG(0x41900030) /* SSP Port 3 Tx Timeslot Active */
-#define SSRSA_P3 __REG(0x41900034) /* SSP Port 3 Rx Timeslot Active */
-#define SSTSS_P3 __REG(0x41900038) /* SSP Port 3 Timeslot Status */
-#define SSACD_P3 __REG(0x4190003C) /* SSP Port 3 Audio Clock Divider */
-#else /* PXA255 (only port 2) and PXA26x ports*/
-#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
-#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
-#define SSCR0_P2 __REG(0x41400000) /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2 __REG(0x41400004) /* SSP Port 2 Control Register 1 */
-#define SSSR_P2 __REG(0x41400008) /* SSP Port 2 Status Register */
-#define SSITR_P2 __REG(0x4140000C) /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2 __REG(0x41400010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2 __REG(0x41400028) /* SSP Port 2 Time Out Register */
-#define SSPSP_P2 __REG(0x4140002C) /* SSP Port 2 Programmable Serial Protocol */
-#define SSCR0_P3 __REG(0x41500000) /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3 __REG(0x41500004) /* SSP Port 3 Control Register 1 */
-#define SSSR_P3 __REG(0x41500008) /* SSP Port 3 Status Register */
-#define SSITR_P3 __REG(0x4150000C) /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3 __REG(0x41500010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3 __REG(0x41500028) /* SSP Port 3 Time Out Register */
-#define SSPSP_P3 __REG(0x4150002C) /* SSP Port 3 Programmable Serial Protocol */
-#endif
-
-#define SSCR0_P(x) (*(((x) == 1) ? &SSCR0_P1 : ((x) == 2) ? &SSCR0_P2 : ((x) == 3) ? &SSCR0_P3 : NULL))
-#define SSCR1_P(x) (*(((x) == 1) ? &SSCR1_P1 : ((x) == 2) ? &SSCR1_P2 : ((x) == 3) ? &SSCR1_P3 : NULL))
-#define SSSR_P(x) (*(((x) == 1) ? &SSSR_P1 : ((x) == 2) ? &SSSR_P2 : ((x) == 3) ? &SSSR_P3 : NULL))
-#define SSITR_P(x) (*(((x) == 1) ? &SSITR_P1 : ((x) == 2) ? &SSITR_P2 : ((x) == 3) ? &SSITR_P3 : NULL))
-#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
-#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
-#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
-#define SSTSA_P(x) (*(((x) == 1) ? &SSTSA_P1 : ((x) == 2) ? &SSTSA_P2 : ((x) == 3) ? &SSTSA_P3 : NULL))
-#define SSRSA_P(x) (*(((x) == 1) ? &SSRSA_P1 : ((x) == 2) ? &SSRSA_P2 : ((x) == 3) ? &SSRSA_P3 : NULL))
-#define SSTSS_P(x) (*(((x) == 1) ? &SSTSS_P1 : ((x) == 2) ? &SSTSS_P2 : ((x) == 3) ? &SSTSS_P3 : NULL))
-#define SSACD_P(x) (*(((x) == 1) ? &SSACD_P1 : ((x) == 2) ? &SSACD_P2 : ((x) == 3) ? &SSACD_P3 : NULL))
-
/*
* MultiMediaCard (MMC) controller - see drivers/mmc/host/pxamci.h
*/
#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
-/*
- * Memory controller
- */
-
-#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
-#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
-#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
-#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
-#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
-#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
-#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
-#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-/*
- * More handy macros for PCMCIA
- *
- * Arg is socket number
- */
-#define MCMEM(s) __REG2(0x48000028, (s)<<2 ) /* Card interface Common Memory Space Socket s Timing */
-#define MCATT(s) __REG2(0x48000030, (s)<<2 ) /* Card interface Attribute Space Socket s Timing Configuration */
-#define MCIO(s) __REG2(0x48000038, (s)<<2 ) /* Card interface I/O Space Socket s Timing Configuration */
-
-/* MECR register defines */
-#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */
-#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */
-
-#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */
-#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
-#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
-#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
-#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */
-#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */
-#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */
-#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */
-#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */
-#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */
-#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */
-#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */
-#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */
-#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
-
-
#ifdef CONFIG_PXA27x
-#define ARB_CNTRL __REG(0x48000048) /* Arbiter Control Register */
-
-#define ARB_DMA_SLV_PARK (1<<31) /* Be parked with DMA slave when idle */
-#define ARB_CI_PARK (1<<30) /* Be parked with Camera Interface when idle */
-#define ARB_EX_MEM_PARK (1<<29) /* Be parked with external MEMC when idle */
-#define ARB_INT_MEM_PARK (1<<28) /* Be parked with internal MEMC when idle */
-#define ARB_USB_PARK (1<<27) /* Be parked with USB when idle */
-#define ARB_LCD_PARK (1<<26) /* Be parked with LCD when idle */
-#define ARB_DMA_PARK (1<<25) /* Be parked with DMA when idle */
-#define ARB_CORE_PARK (1<<24) /* Be parked with core when idle */
-#define ARB_LOCK_FLAG (1<<23) /* Only Locking masters gain access to the bus */
-
/*
* Keypad
*/
#define KPAS_SO (0x1 << 31)
#define KPASMKPx_SO (0x1 << 31)
-/*
- * UHC: USB Host Controller (OHCI-like) register definitions
- */
-#define UHC_BASE_PHYS (0x4C000000)
-#define UHCREV __REG(0x4C000000) /* UHC HCI Spec Revision */
-#define UHCHCON __REG(0x4C000004) /* UHC Host Control Register */
-#define UHCCOMS __REG(0x4C000008) /* UHC Command Status Register */
-#define UHCINTS __REG(0x4C00000C) /* UHC Interrupt Status Register */
-#define UHCINTE __REG(0x4C000010) /* UHC Interrupt Enable */
-#define UHCINTD __REG(0x4C000014) /* UHC Interrupt Disable */
-#define UHCHCCA __REG(0x4C000018) /* UHC Host Controller Comm. Area */
-#define UHCPCED __REG(0x4C00001C) /* UHC Period Current Endpt Descr */
-#define UHCCHED __REG(0x4C000020) /* UHC Control Head Endpt Descr */
-#define UHCCCED __REG(0x4C000024) /* UHC Control Current Endpt Descr */
-#define UHCBHED __REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
-#define UHCBCED __REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
-#define UHCDHEAD __REG(0x4C000030) /* UHC Done Head */
-#define UHCFMI __REG(0x4C000034) /* UHC Frame Interval */
-#define UHCFMR __REG(0x4C000038) /* UHC Frame Remaining */
-#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
-#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
-#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
-
-#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
-#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
-
-#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
-#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
-#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
-#define UHCRHPS2 __REG(0x4C000058) /* UHC Root Hub Port 2 Status */
-#define UHCRHPS3 __REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
-
-#define UHCSTAT __REG(0x4C000060) /* UHC Status Register */
-#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
-#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
-#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
-#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
-#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
-#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
-#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
-#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
-#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
-
-#define UHCHR __REG(0x4C000064) /* UHC Reset Register */
-#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
-#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
-#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
-#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
-#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
-#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
-#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
-#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
-#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
-#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
-#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
-
-#define UHCHIE __REG(0x4C000068) /* UHC Interrupt Enable Register*/
-#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
-#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
-#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
-#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
-#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
- Interrupt Enable*/
-#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
-#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
-
-#define UHCHIT __REG(0x4C00006C) /* UHC Interrupt Test register */
-
/* Camera Interface */
#define CICR0 __REG(0x50000000)
#define CICR1 __REG(0x50000004)
#endif
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+/*
+ * UHC: USB Host Controller (OHCI-like) register definitions
+ */
+#define UHC_BASE_PHYS (0x4C000000)
+#define UHCREV __REG(0x4C000000) /* UHC HCI Spec Revision */
+#define UHCHCON __REG(0x4C000004) /* UHC Host Control Register */
+#define UHCCOMS __REG(0x4C000008) /* UHC Command Status Register */
+#define UHCINTS __REG(0x4C00000C) /* UHC Interrupt Status Register */
+#define UHCINTE __REG(0x4C000010) /* UHC Interrupt Enable */
+#define UHCINTD __REG(0x4C000014) /* UHC Interrupt Disable */
+#define UHCHCCA __REG(0x4C000018) /* UHC Host Controller Comm. Area */
+#define UHCPCED __REG(0x4C00001C) /* UHC Period Current Endpt Descr */
+#define UHCCHED __REG(0x4C000020) /* UHC Control Head Endpt Descr */
+#define UHCCCED __REG(0x4C000024) /* UHC Control Current Endpt Descr */
+#define UHCBHED __REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
+#define UHCBCED __REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
+#define UHCDHEAD __REG(0x4C000030) /* UHC Done Head */
+#define UHCFMI __REG(0x4C000034) /* UHC Frame Interval */
+#define UHCFMR __REG(0x4C000038) /* UHC Frame Remaining */
+#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
+#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
+#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
+
+#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
+#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
+
+#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
+#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
+#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
+#define UHCRHPS2 __REG(0x4C000058) /* UHC Root Hub Port 2 Status */
+#define UHCRHPS3 __REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
+
+#define UHCSTAT __REG(0x4C000060) /* UHC Status Register */
+#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
+#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
+#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
+#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
+#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
+#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
+#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
+#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
+#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
+
+#define UHCHR __REG(0x4C000064) /* UHC Reset Register */
+#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
+#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
+#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
+#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
+#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
+#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
+#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
+#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
+#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
+#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
+#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
+
+#define UHCHIE __REG(0x4C000068) /* UHC Interrupt Enable Register*/
+#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
+#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
+#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
+#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
+#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
+ Interrupt Enable*/
+#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
+#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
+
+#define UHCHIT __REG(0x4C00006C) /* UHC Interrupt Test register */
+
+#endif /* CONFIG_PXA27x || CONFIG_PXA3xx */
+
/* PWRMODE register M field values */
#define PWRMODE_IDLE 0x1
projects / linux-2.6-omap-h63xx.git / blobdiff