#include <asm/immap_cpm2.h>
#include <asm/cpm.h>
+#include <sysdev/fsl_soc.h>
#ifdef CONFIG_PPC_85xx
#define CPM_MAP_ADDR (get_immrbase() + 0x80000)
#define mk_cr_cmd(PG, SBC, MCN, OP) \
((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Dual Port RAM addresses. The first 16K is available for almost
- * any CPM use, so we put the BDs there. The first 128 bytes are
- * used for SMC1 and SMC2 parameter RAM, so we start allocating
- * BDs above that. All of this must change when we start
- * downloading RAM microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)128)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
-#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
-#else
-#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
-#endif
-#endif
-
/* The number of pages of host memory we allocate for CPM. This is
* done early in kernel initialization to get physically contiguous
* pages.
*/
extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-#endif
-extern void cpm_setbrg(uint brg, uint rate);
-extern void cpm2_fastbrg(uint brg, uint rate, int div16);
extern void cpm2_reset(void);
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST ((uint)0x00020000)
+#define CPM_BRG_EN ((uint)0x00010000)
+#define CPM_BRG_EXTC_INT ((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
+#define CPM_BRG_ATB ((uint)0x00002000)
+#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
+#define CPM_BRG_DIV16 ((uint)0x00000001)
+
+#define CPM2_BRG_INT_CLK (get_brgfreq())
+#define CPM2_BRG_UART_CLK (CPM2_BRG_INT_CLK/16)
+
+extern void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src);
+
+/* This function is used by UARTS, or anything else that uses a 16x
+ * oversampled clock.
+ */
+static inline void cpm_setbrg(uint brg, uint rate)
+{
+ __cpm2_setbrg(brg, rate, CPM2_BRG_UART_CLK, 0, CPM_BRG_EXTC_INT);
+}
+
+/* This function is used to set high speed synchronous baud rate
+ * clocks.
+ */
+static inline void cpm2_fastbrg(uint brg, uint rate, int div16)
+{
+ __cpm2_setbrg(brg, rate, CPM2_BRG_INT_CLK, div16, CPM_BRG_EXTC_INT);
+}
+
/* Function code bits, usually generic to devices.
*/
#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */
#define SMCM_TX ((unsigned char)0x02)
#define SMCM_RX ((unsigned char)0x01)
-/* Baud rate generators.
-*/
-#define CPM_BRG_RST ((uint)0x00020000)
-#define CPM_BRG_EN ((uint)0x00010000)
-#define CPM_BRG_EXTC_INT ((uint)0x00000000)
-#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
-#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
-#define CPM_BRG_ATB ((uint)0x00002000)
-#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
-#define CPM_BRG_DIV16 ((uint)0x00000001)
-
/* SCCs.
*/
#define SCC_GSMRH_IRP ((uint)0x00040000)