* enum ieee80211_max_queues - maximum number of queues
*
* @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
- * @IEEE80211_MAX_AMPDU_QUEUES: Maximum number of queues usable
- * for A-MPDU operation.
*/
enum ieee80211_max_queues {
- IEEE80211_MAX_QUEUES = 16,
- IEEE80211_MAX_AMPDU_QUEUES = 16,
+ IEEE80211_MAX_QUEUES = 4,
};
/**
* @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
* set by rate control algorithms to indicate probe rate, will
* be cleared for fragmented frames (except on the last fragment)
+ * @IEEE80211_TX_INTFL_RCALGO: mac80211 internal flag, do not test or
+ * set this flag in the driver; indicates that the rate control
+ * algorithm was used and should be notified of TX status
+ * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
+ * used to indicate that a pending frame requires TX processing before
+ * it can be sent out.
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
IEEE80211_TX_STAT_AMPDU = BIT(10),
IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
+ IEEE80211_TX_INTFL_RCALGO = BIT(13),
+ IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
};
/**
IEEE80211_CONF_PS = (1<<1),
};
-/* XXX: remove all this once drivers stop trying to use it */
-static inline int __deprecated __IEEE80211_CONF_SHORT_SLOT_TIME(void)
-{
- return 0;
-}
-#define IEEE80211_CONF_SHORT_SLOT_TIME (__IEEE80211_CONF_SHORT_SLOT_TIME())
/**
* enum ieee80211_conf_changed - denotes which configuration changed
*
* @IEEE80211_HW_MFP_CAPABLE:
* Hardware supports management frame protection (MFP, IEEE 802.11w).
+ *
+ * @IEEE80211_HW_BEACON_FILTER:
+ * Hardware supports dropping of irrelevant beacon frames to
+ * avoid waking up cpu.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
IEEE80211_HW_MFP_CAPABLE = 1<<13,
+ IEEE80211_HW_BEACON_FILTER = 1<<14,
};
/**
* data packets. WMM/QoS requires at least four, these
* queues need to have configurable access parameters.
*
- * @ampdu_queues: number of available hardware transmit queues
- * for A-MPDU packets, these have no access parameters
- * because they're used only for A-MPDU frames. Note that
- * mac80211 will not currently use any of the regular queues
- * for aggregation.
- *
* @rate_control_algorithm: rate control algorithm for this hardware.
* If unset (NULL), the default algorithm will be used. Must be
* set before calling ieee80211_register_hw().
int vif_data_size;
int sta_data_size;
u16 queues;
- u16 ampdu_queues;
u16 max_listen_interval;
s8 max_signal;
u8 max_rates;
memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}
-static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
-{
- return hw->queues;
-}
-
static inline struct ieee80211_rate *
ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
const struct ieee80211_tx_info *c)
* value, or by the stack if all nullfunc handling is in the stack.
*/
+/**
+ * DOC: Beacon filter support
+ *
+ * Some hardware have beacon filter support to reduce host cpu wakeups
+ * which will reduce system power consumption. It usuallly works so that
+ * the firmware creates a checksum of the beacon but omits all constantly
+ * changing elements (TSF, TIM etc). Whenever the checksum changes the
+ * beacon is forwarded to the host, otherwise it will be just dropped. That
+ * way the host will only receive beacons where some relevant information
+ * (for example ERP protection or WMM settings) have changed.
+ *
+ * Beacon filter support is informed with %IEEE80211_HW_BEACON_FILTER flag.
+ * The driver needs to enable beacon filter support whenever power save is
+ * enabled, that is %IEEE80211_CONF_PS is set. When power save is enabled,
+ * the stack will not check for beacon miss at all and the driver needs to
+ * notify about complete loss of beacons with ieee80211_beacon_loss().
+ */
+
/**
* DOC: Frame filtering
*
* @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
* @IEEE80211_AMPDU_TX_START: start Tx aggregation
* @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
- * @IEEE80211_AMPDU_TX_RESUME: resume TX aggregation
+ * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
*/
enum ieee80211_ampdu_mlme_action {
IEEE80211_AMPDU_RX_START,
IEEE80211_AMPDU_RX_STOP,
IEEE80211_AMPDU_TX_START,
IEEE80211_AMPDU_TX_STOP,
- IEEE80211_AMPDU_TX_RESUME,
+ IEEE80211_AMPDU_TX_OPERATIONAL,
};
/**
*
* @hw_scan: Ask the hardware to service the scan request, no need to start
* the scan state machine in stack. The scan must honour the channel
- * configuration done by the regulatory agent in the wiphy's registered
- * bands. When the scan finishes, ieee80211_scan_completed() must be
- * called; note that it also must be called when the scan cannot finish
- * because the hardware is turned off! Anything else is a bug!
- * Returns a negative error code which will be seen in userspace.
+ * configuration done by the regulatory agent in the wiphy's
+ * registered bands. The hardware (or the driver) needs to make sure
+ * that power save is disabled. When the scan finishes,
+ * ieee80211_scan_completed() must be called; note that it also must
+ * be called when the scan cannot finish because the hardware is
+ * turned off! Anything else is a bug! Returns a negative error code
+ * which will be seen in userspace.
*
* @sw_scan_start: Notifier function that is called just before a software scan
* is started. Can be NULL, if the driver doesn't need this notification.
* @get_tx_stats: Get statistics of the current TX queue status. This is used
* to get number of currently queued packets (queue length), maximum queue
* size (limit), and total number of packets sent using each TX queue
- * (count). The 'stats' pointer points to an array that has hw->queues +
- * hw->ampdu_queues items.
+ * (count). The 'stats' pointer points to an array that has hw->queues
+ * items.
*
* @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
* this is only used for IBSS mode BSSID merging and debugging. Is not a
struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_hw *hw,
const u8 *addr);
+/**
+ * ieee80211_beacon_loss - inform hardware does not receive beacons
+ *
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
+ *
+ * When beacon filtering is enabled with IEEE80211_HW_BEACON_FILTERING and
+ * IEEE80211_CONF_PS is set, the driver needs to inform whenever the
+ * hardware is not receiving beacons with this function.
+ */
+void ieee80211_beacon_loss(struct ieee80211_vif *vif);
/* Rate control API */
projects / linux-2.6-omap-h63xx.git / blobdiff