[NET]: prot_inuse cleanups and optimizations

[linux-2.6-omap-h63xx.git] / net / mac80211 / Kconfig

diff --git a/net/mac80211/Kconfig b/net/mac80211/Kconfig
index d761b53fb84c3023b7805fa772a416699d10f57e..cac6cf2e9ac84c672ba4dad57dca6035882cde50 100644 (file)
--- a/net/mac80211/Kconfig
+++ b/net/mac80211/Kconfig
@@ -10,15 +10,94 @@ config MAC80211
        select CFG80211
        select NET_SCH_FIFO
        ---help---
-       This option enables the hardware independent IEEE 802.11
-       networking stack.
+         This option enables the hardware independent IEEE 802.11
+         networking stack.
+
+config MAC80211_RC_DEFAULT_CHOICE
+       bool "Choose default rate control algorithm" if EMBEDDED
+       default y
+       depends on MAC80211
+       ---help---
+         This options enables selection of a default rate control
+         algorithm to be built into the mac80211 module.  Alternate
+         rate control algorithms might be built into the mac80211
+         module as well.
+
+choice
+       prompt "Default rate control algorithm"
+       default MAC80211_RC_DEFAULT_PID
+       depends on MAC80211 && MAC80211_RC_DEFAULT_CHOICE
+       ---help---
+         This option selects the default rate control algorithm
+         mac80211 will use. Note that this default can still be
+         overriden through the ieee80211_default_rc_algo module
+         parameter.
+
+config MAC80211_RC_DEFAULT_PID
+       bool "PID controller based rate control algorithm"
+       select MAC80211_RC_PID
+       ---help---
+         Select the PID controller based rate control as the
+         default rate control algorithm. You should choose
+         this unless you know what you are doing.
+
+config MAC80211_RC_DEFAULT_SIMPLE
+       bool "Simple rate control algorithm"
+       select MAC80211_RC_SIMPLE
+       ---help---
+         Select the simple rate control as the default rate
+         control algorithm. Note that this is a non-responsive,
+         dumb algorithm. You should choose the PID rate control
+         instead.
+
+endchoice
+
+config MAC80211_RC_DEFAULT
+       string
+       depends on MAC80211
+       default "pid" if MAC80211_RC_DEFAULT_PID
+       default "simple" if MAC80211_RC_DEFAULT_SIMPLE
+       default ""
+
+config MAC80211_RC_PID
+       bool "PID controller based rate control algorithm"
+       default y
+       depends on MAC80211
+       ---help---
+         This option enables a TX rate control algorithm for
+         mac80211 that uses a PID controller to select the TX
+         rate.
+
+         Say Y or M unless you're sure you want to use a
+         different rate control algorithm.
+
+config MAC80211_RC_SIMPLE
+       bool "Simple rate control algorithm (DEPRECATED)"
+       default n
+       depends on MAC80211
+       ---help---
+         This option enables a very simple, non-responsive TX
+         rate control algorithm. This algorithm is deprecated
+         and will be removed from the kernel in near future.
+         It has been replaced by the PID algorithm.
+
+         Say N unless you know what you are doing.
 
 config MAC80211_LEDS
        bool "Enable LED triggers"
        depends on MAC80211 && LEDS_TRIGGERS
        ---help---
-       This option enables a few LED triggers for different
-       packet receive/transmit events.
+         This option enables a few LED triggers for different
+         packet receive/transmit events.
+
+config MAC80211_DEBUGFS
+       bool "Export mac80211 internals in DebugFS"
+       depends on MAC80211 && DEBUG_FS
+       ---help---
+         Select this to see extensive information about
+         the internal state of mac80211 in debugfs.
+
+         Say N unless you know you need this.
 
 config MAC80211_DEBUG
        bool "Enable debugging output"
@@ -30,6 +109,16 @@ config MAC80211_DEBUG
          If you are not trying to debug or develop the ieee80211
          subsystem, you most likely want to say N here.
 
+config MAC80211_HT_DEBUG
+       bool "Enable HT debugging output"
+       depends on MAC80211_DEBUG
+       ---help---
+         This option enables 802.11n High Throughput features
+         debug tracing output.
+
+         If you are not trying to debug of develop the ieee80211
+         subsystem, you most likely want to say N here.
+
 config MAC80211_VERBOSE_DEBUG
        bool "Verbose debugging output"
        depends on MAC80211_DEBUG