X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;ds=sidebyside;f=drivers%2Fata%2Flibata-core.c;h=33f06277b3be2ab81f41c539ea19f65227867e1f;hb=6d272940537e834848d88c11b428e9973b8fa2bc;hp=81898036dbcaa8badff43fb0a95089a5c3402164;hpb=95b00786f3b8fa99f53931361beeb4c10504ad87;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 81898036dbc..33f06277b3b 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -30,6 +30,14 @@
  *  Hardware documentation available from http://www.t13.org/ and
  *  http://www.sata-io.org/
  *
+ *  Standards documents from:
+ *	http://www.t13.org (ATA standards, PCI DMA IDE spec)
+ *	http://www.t10.org (SCSI MMC - for ATAPI MMC)
+ *	http://www.sata-io.org (SATA)
+ *	http://www.compactflash.org (CF)
+ *	http://www.qic.org (QIC157 - Tape and DSC)
+ *	http://www.ce-ata.org (CE-ATA: not supported)
+ *
  */
 
 #include <linux/kernel.h>
@@ -2307,8 +2315,10 @@ int ata_dev_configure(struct ata_device *dev)
 	}
 
 	if ((dev->class == ATA_DEV_ATAPI) &&
-	    (atapi_command_packet_set(id) == TYPE_TAPE))
+	    (atapi_command_packet_set(id) == TYPE_TAPE)) {
 		dev->max_sectors = ATA_MAX_SECTORS_TAPE;
+		dev->horkage |= ATA_HORKAGE_STUCK_ERR;
+	}
 
 	if (dev->horkage & ATA_HORKAGE_MAX_SEC_128)
 		dev->max_sectors = min_t(unsigned int, ATA_MAX_SECTORS_128,
@@ -2580,81 +2590,6 @@ void sata_print_link_status(struct ata_link *link)
 	}
 }
 
-/**
- *	__sata_phy_reset - Wake/reset a low-level SATA PHY
- *	@ap: SATA port associated with target SATA PHY.
- *
- *	This function issues commands to standard SATA Sxxx
- *	PHY registers, to wake up the phy (and device), and
- *	clear any reset condition.
- *
- *	LOCKING:
- *	PCI/etc. bus probe sem.
- *
- */
-void __sata_phy_reset(struct ata_port *ap)
-{
-	struct ata_link *link = &ap->link;
-	unsigned long timeout = jiffies + (HZ * 5);
-	u32 sstatus;
-
-	if (ap->flags & ATA_FLAG_SATA_RESET) {
-		/* issue phy wake/reset */
-		sata_scr_write_flush(link, SCR_CONTROL, 0x301);
-		/* Couldn't find anything in SATA I/II specs, but
-		 * AHCI-1.1 10.4.2 says at least 1 ms. */
-		mdelay(1);
-	}
-	/* phy wake/clear reset */
-	sata_scr_write_flush(link, SCR_CONTROL, 0x300);
-
-	/* wait for phy to become ready, if necessary */
-	do {
-		msleep(200);
-		sata_scr_read(link, SCR_STATUS, &sstatus);
-		if ((sstatus & 0xf) != 1)
-			break;
-	} while (time_before(jiffies, timeout));
-
-	/* print link status */
-	sata_print_link_status(link);
-
-	/* TODO: phy layer with polling, timeouts, etc. */
-	if (!ata_link_offline(link))
-		ata_port_probe(ap);
-	else
-		ata_port_disable(ap);
-
-	if (ap->flags & ATA_FLAG_DISABLED)
-		return;
-
-	if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
-		ata_port_disable(ap);
-		return;
-	}
-
-	ap->cbl = ATA_CBL_SATA;
-}
-
-/**
- *	sata_phy_reset - Reset SATA bus.
- *	@ap: SATA port associated with target SATA PHY.
- *
- *	This function resets the SATA bus, and then probes
- *	the bus for devices.
- *
- *	LOCKING:
- *	PCI/etc. bus probe sem.
- *
- */
-void sata_phy_reset(struct ata_port *ap)
-{
-	__sata_phy_reset(ap);
-	if (ap->flags & ATA_FLAG_DISABLED)
-		return;
-	ata_bus_reset(ap);
-}
-
 /**
  *	ata_dev_pair		-	return other device on cable
  *	@adev: device
@@ -5490,11 +5425,19 @@ fsm_start:
 		 * let the EH abort the command or reset the device.
 		 */
 		if (unlikely(status & (ATA_ERR | ATA_DF))) {
-			ata_port_printk(ap, KERN_WARNING, "DRQ=1 with device "
-					"error, dev_stat 0x%X\n", status);
-			qc->err_mask |= AC_ERR_HSM;
-			ap->hsm_task_state = HSM_ST_ERR;
-			goto fsm_start;
+			/* Some ATAPI tape drives forget to clear the ERR bit
+			 * when doing the next command (mostly request sense).
+			 * We ignore ERR here to workaround and proceed sending
+			 * the CDB.
+			 */
+			if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
+				ata_port_printk(ap, KERN_WARNING,
+						"DRQ=1 with device error, "
+						"dev_stat 0x%X\n", status);
+				qc->err_mask |= AC_ERR_HSM;
+				ap->hsm_task_state = HSM_ST_ERR;
+				goto fsm_start;
+			}
 		}
 
 		/* Send the CDB (atapi) or the first data block (ata pio out).
@@ -7653,8 +7596,6 @@ EXPORT_SYMBOL_GPL(ata_dev_disable);
 EXPORT_SYMBOL_GPL(sata_set_spd);
 EXPORT_SYMBOL_GPL(sata_link_debounce);
 EXPORT_SYMBOL_GPL(sata_link_resume);
-EXPORT_SYMBOL_GPL(sata_phy_reset);
-EXPORT_SYMBOL_GPL(__sata_phy_reset);
 EXPORT_SYMBOL_GPL(ata_bus_reset);
 EXPORT_SYMBOL_GPL(ata_std_prereset);
 EXPORT_SYMBOL_GPL(ata_std_softreset);
@@ -7725,7 +7666,6 @@ EXPORT_SYMBOL_GPL(ata_port_desc);
 #ifdef CONFIG_PCI
 EXPORT_SYMBOL_GPL(ata_port_pbar_desc);
 #endif /* CONFIG_PCI */
-EXPORT_SYMBOL_GPL(ata_eng_timeout);
 EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
 EXPORT_SYMBOL_GPL(ata_link_abort);
 EXPORT_SYMBOL_GPL(ata_port_abort);