X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;ds=sidebyside;f=drivers%2Fnet%2Fnatsemi.c;h=5657049c216041faea5c59f61e37898643f14447;hb=501b7c77de3e90519e95fd99e923bf9a29cd120d;hp=90627756d6fa47bbe93ce363af1d6ced2307fba4;hpb=60e04a5c533785c23ce6b76a6e5058328fe68edb;p=linux-2.6-omap-h63xx.git diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c index 90627756d6f..5657049c216 100644 --- a/drivers/net/natsemi.c +++ b/drivers/net/natsemi.c @@ -226,7 +226,6 @@ static int full_duplex[MAX_UNITS]; NATSEMI_PG1_NREGS) #define NATSEMI_REGS_VER 1 /* v1 added RFDR registers */ #define NATSEMI_REGS_SIZE (NATSEMI_NREGS * sizeof(u32)) -#define NATSEMI_DEF_EEPROM_SIZE 24 /* 12 16-bit values */ /* Buffer sizes: * The nic writes 32-bit values, even if the upper bytes of @@ -318,12 +317,12 @@ performance critical codepaths: The rx process only runs in the interrupt handler. Access from outside the interrupt handler is only permitted after disable_irq(). -The rx process usually runs under the dev->xmit_lock. If np->intr_tx_reap +The rx process usually runs under the netif_tx_lock. If np->intr_tx_reap is set, then access is permitted under spin_lock_irq(&np->lock). Thus configuration functions that want to access everything must call disable_irq(dev->irq); - spin_lock_bh(dev->xmit_lock); + netif_tx_lock_bh(dev); spin_lock_irq(&np->lock); IV. Notes @@ -344,18 +343,6 @@ None characterised. -enum pcistuff { - PCI_USES_IO = 0x01, - PCI_USES_MEM = 0x02, - PCI_USES_MASTER = 0x04, - PCI_ADDR0 = 0x08, - PCI_ADDR1 = 0x10, -}; - -/* MMIO operations required */ -#define PCI_IOTYPE (PCI_USES_MASTER | PCI_USES_MEM | PCI_ADDR1) - - /* * Support for fibre connections on Am79C874: * This phy needs a special setup when connected to a fibre cable. @@ -363,22 +350,25 @@ enum pcistuff { */ #define PHYID_AM79C874 0x0022561b -#define MII_MCTRL 0x15 /* mode control register */ -#define MII_FX_SEL 0x0001 /* 100BASE-FX (fiber) */ -#define MII_EN_SCRM 0x0004 /* enable scrambler (tp) */ +enum { + MII_MCTRL = 0x15, /* mode control register */ + MII_FX_SEL = 0x0001, /* 100BASE-FX (fiber) */ + MII_EN_SCRM = 0x0004, /* enable scrambler (tp) */ +}; /* array of board data directly indexed by pci_tbl[x].driver_data */ static const struct { const char *name; unsigned long flags; + unsigned int eeprom_size; } natsemi_pci_info[] __devinitdata = { - { "NatSemi DP8381[56]", PCI_IOTYPE }, + { "NatSemi DP8381[56]", 0, 24 }, }; -static struct pci_device_id natsemi_pci_tbl[] = { - { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_83815, PCI_ANY_ID, PCI_ANY_ID, }, - { 0, }, +static const struct pci_device_id natsemi_pci_tbl[] __devinitdata = { + { PCI_VENDOR_ID_NS, 0x0020, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, + { } /* terminate list */ }; MODULE_DEVICE_TABLE(pci, natsemi_pci_tbl); @@ -813,6 +803,42 @@ static void move_int_phy(struct net_device *dev, int addr) udelay(1); } +static void __devinit natsemi_init_media (struct net_device *dev) +{ + struct netdev_private *np = netdev_priv(dev); + u32 tmp; + + netif_carrier_off(dev); + + /* get the initial settings from hardware */ + tmp = mdio_read(dev, MII_BMCR); + np->speed = (tmp & BMCR_SPEED100)? SPEED_100 : SPEED_10; + np->duplex = (tmp & BMCR_FULLDPLX)? DUPLEX_FULL : DUPLEX_HALF; + np->autoneg = (tmp & BMCR_ANENABLE)? AUTONEG_ENABLE: AUTONEG_DISABLE; + np->advertising= mdio_read(dev, MII_ADVERTISE); + + if ((np->advertising & ADVERTISE_ALL) != ADVERTISE_ALL + && netif_msg_probe(np)) { + printk(KERN_INFO "natsemi %s: Transceiver default autonegotiation %s " + "10%s %s duplex.\n", + pci_name(np->pci_dev), + (mdio_read(dev, MII_BMCR) & BMCR_ANENABLE)? + "enabled, advertise" : "disabled, force", + (np->advertising & + (ADVERTISE_100FULL|ADVERTISE_100HALF))? + "0" : "", + (np->advertising & + (ADVERTISE_100FULL|ADVERTISE_10FULL))? + "full" : "half"); + } + if (netif_msg_probe(np)) + printk(KERN_INFO + "natsemi %s: Transceiver status %#04x advertising %#04x.\n", + pci_name(np->pci_dev), mdio_read(dev, MII_BMSR), + np->advertising); + +} + static int __devinit natsemi_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -852,8 +878,7 @@ static int __devinit natsemi_probe1 (struct pci_dev *pdev, iosize = pci_resource_len(pdev, pcibar); irq = pdev->irq; - if (natsemi_pci_info[chip_idx].flags & PCI_USES_MASTER) - pci_set_master(pdev); + pci_set_master(pdev); dev = alloc_etherdev(sizeof (struct netdev_private)); if (!dev) @@ -892,7 +917,7 @@ static int __devinit natsemi_probe1 (struct pci_dev *pdev, np->msg_enable = (debug >= 0) ? (1<hands_off = 0; np->intr_status = 0; - np->eeprom_size = NATSEMI_DEF_EEPROM_SIZE; + np->eeprom_size = natsemi_pci_info[chip_idx].eeprom_size; /* Initial port: * - If the nic was configured to use an external phy and if find_mii @@ -957,34 +982,7 @@ static int __devinit natsemi_probe1 (struct pci_dev *pdev, if (mtu) dev->mtu = mtu; - netif_carrier_off(dev); - - /* get the initial settings from hardware */ - tmp = mdio_read(dev, MII_BMCR); - np->speed = (tmp & BMCR_SPEED100)? SPEED_100 : SPEED_10; - np->duplex = (tmp & BMCR_FULLDPLX)? DUPLEX_FULL : DUPLEX_HALF; - np->autoneg = (tmp & BMCR_ANENABLE)? AUTONEG_ENABLE: AUTONEG_DISABLE; - np->advertising= mdio_read(dev, MII_ADVERTISE); - - if ((np->advertising & ADVERTISE_ALL) != ADVERTISE_ALL - && netif_msg_probe(np)) { - printk(KERN_INFO "natsemi %s: Transceiver default autonegotiation %s " - "10%s %s duplex.\n", - pci_name(np->pci_dev), - (mdio_read(dev, MII_BMCR) & BMCR_ANENABLE)? - "enabled, advertise" : "disabled, force", - (np->advertising & - (ADVERTISE_100FULL|ADVERTISE_100HALF))? - "0" : "", - (np->advertising & - (ADVERTISE_100FULL|ADVERTISE_10FULL))? - "full" : "half"); - } - if (netif_msg_probe(np)) - printk(KERN_INFO - "natsemi %s: Transceiver status %#04x advertising %#04x.\n", - pci_name(np->pci_dev), mdio_read(dev, MII_BMSR), - np->advertising); + natsemi_init_media(dev); /* save the silicon revision for later querying */ np->srr = readl(ioaddr + SiliconRev);