X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Ffilesystems%2Fproc.txt;h=7aaf09b86a552210584f6e346ad903b10a9cb0b6;hb=bc95f3669f5e6f63cf0b84fe4922c3c6dd4aa775;hp=72af5de1effb44a93d907ed4e0117ec403a8257e;hpb=c3e59d1e891f6140a346de2b8547e25133c716b0;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index 72af5de1eff..7aaf09b86a5 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -41,6 +41,7 @@ Table of Contents
   2.11	/proc/sys/fs/mqueue - POSIX message queues filesystem
   2.12	/proc/<pid>/oom_adj - Adjust the oom-killer score
   2.13	/proc/<pid>/oom_score - Display current oom-killer score
+  2.14	/proc/<pid>/io - Display the IO accounting fields
 
 ------------------------------------------------------------------------------
 Preface
@@ -1420,6 +1421,15 @@ fewer messages that will be written. Message_burst controls when messages will
 be dropped.  The  default  settings  limit  warning messages to one every five
 seconds.
 
+warnings
+--------
+
+This controls console messages from the networking stack that can occur because
+of problems on the network like duplicate address or bad checksums. Normally,
+this should be enabled, but if the problem persists the messages can be
+disabled.
+
+
 netdev_max_backlog
 ------------------
 
@@ -1990,3 +2000,107 @@ need to  recompile  the kernel, or even to reboot the system. The files in the
 command to write value into these files, thereby changing the default settings
 of the kernel.
 ------------------------------------------------------------------------------
+
+2.14  /proc/<pid>/io - Display the IO accounting fields
+-------------------------------------------------------
+
+This file contains IO statistics for each running process
+
+Example
+-------
+
+test:/tmp # dd if=/dev/zero of=/tmp/test.dat &
+[1] 3828
+
+test:/tmp # cat /proc/3828/io
+rchar: 323934931
+wchar: 323929600
+syscr: 632687
+syscw: 632675
+read_bytes: 0
+write_bytes: 323932160
+cancelled_write_bytes: 0
+
+
+Description
+-----------
+
+rchar
+-----
+
+I/O counter: chars read
+The number of bytes which this task has caused to be read from storage. This
+is simply the sum of bytes which this process passed to read() and pread().
+It includes things like tty IO and it is unaffected by whether or not actual
+physical disk IO was required (the read might have been satisfied from
+pagecache)
+
+
+wchar
+-----
+
+I/O counter: chars written
+The number of bytes which this task has caused, or shall cause to be written
+to disk. Similar caveats apply here as with rchar.
+
+
+syscr
+-----
+
+I/O counter: read syscalls
+Attempt to count the number of read I/O operations, i.e. syscalls like read()
+and pread().
+
+
+syscw
+-----
+
+I/O counter: write syscalls
+Attempt to count the number of write I/O operations, i.e. syscalls like
+write() and pwrite().
+
+
+read_bytes
+----------
+
+I/O counter: bytes read
+Attempt to count the number of bytes which this process really did cause to
+be fetched from the storage layer. Done at the submit_bio() level, so it is
+accurate for block-backed filesystems. <please add status regarding NFS and
+CIFS at a later time>
+
+
+write_bytes
+-----------
+
+I/O counter: bytes written
+Attempt to count the number of bytes which this process caused to be sent to
+the storage layer. This is done at page-dirtying time.
+
+
+cancelled_write_bytes
+---------------------
+
+The big inaccuracy here is truncate. If a process writes 1MB to a file and
+then deletes the file, it will in fact perform no writeout. But it will have
+been accounted as having caused 1MB of write.
+In other words: The number of bytes which this process caused to not happen,
+by truncating pagecache. A task can cause "negative" IO too. If this task
+truncates some dirty pagecache, some IO which another task has been accounted
+for (in it's write_bytes) will not be happening. We _could_ just subtract that
+from the truncating task's write_bytes, but there is information loss in doing
+that.
+
+
+Note
+----
+
+At its current implementation state, this is a bit racy on 32-bit machines: if
+process A reads process B's /proc/pid/io while process B is updating one of
+those 64-bit counters, process A could see an intermediate result.
+
+
+More information about this can be found within the taskstats documentation in
+Documentation/accounting.
+
+------------------------------------------------------------------------------